Engineering Mechanical

Objective

A mechanical graduate student seeking a full time position where I can utilize my technical, analytical skills to enhance organizational and personal growth.

Education

Southern Illinois University Edwardsville (SIUE) August 2014 – May 2016

Master of Science in Mechanical Engineering, GPA: 3.5 / 4.0

Vellore Institute of Technology (VIT) July 2010 – June 2014

Bachelor of Technology, Mechanical Engineering, GPA: 3.3 / 4.0 Degree accredited by ABET

Professional Profile

Adept at using Solidworks, AutoCAD, Revit, Autodesk Inventor and ANSYS.

Hands on experience in designing HVAC systems using AutoCAD and Revit.

In-depth knowledge on HVAC systems and design methodology.

Proficient in HVAC psychrometric analysis, heating and cooling load calculations.

Sound knowledge on Sheet metal fabrication and manufacturing processes.

Proficient in using Microsoft Excel, writing reports and developing cost estimates.

Good knowledge on vehicle components, powertrains and internal combustion engines.

Comprehensive knowledge on mechanical principles and drafting techniques.

Relevant Coursework

Heating, Ventilating and Air Conditioning Project Management

Gas Turbines Automobile Engineering

Computational Fluid Dynamics Advanced Fluid Mechanics

Engineering Graphics Heat and Mass Transfer

Refrigeration and Air Conditioning Advanced Dynamics

Turbomachines Manufacturing Engineering

Academic Projects

HVAC system design of a Residential Building

Designed and Budgeted the HVAC system of a building.

Identified zones that are to be controlled independently and calculated heating and cooling loads for each zone.

Selected the equipment based on heating and cooling load capacities of the zones.

Successfully interpreted the design to identify flaws and inconsistencies using AutoCAD.

Successfully sized the ducts based on friction rates to provide required CFM using equal-friction method. Achieved the velocity and temperature distributions on the duct work to provide economic design.

Chemical Migration through Overburden in Hydrofracking Technology (Shale Gas Fracking)

Designed and simulated the geometrical stratigraphies of Marcellus, Bowland and Bakken Shale Gas formations.

Designs successfully helped in obtaining the velocity and dynamic pressure ranges of various chemicals used in hydraulic fracturing technique.

Succeeded in determining if the chemicals can reach the ground water aquifers in each geometrical stratigraphy.

Design Analysis and Optimization of a Connecting Rod in Internal Combustion Engines

Designed and simulated the connecting rod of a two wheeler I.C. Engine (Pulsar 200NS) using Solidworks.

Successful in detecting the loads acting on the connecting rod as a function of time at a constant speed of crank shaft.

Identified the weight reduction opportunities by examining various materials such as Aluminum alloy, Tool steel and Titanium alloy and succeeded in minimizing the deflection in connecting rod.

Fluid Flow Analysis through a Channel

Designed and simulated fluid flow through two concentric circular and octagonal bodies.

Considered the material as iron, water as heat transfer fluid and the inner body acts as a heat source.

Successfully obtained velocity, pressure and temperature distributions along both the channels.

Design of Multi-Linkage Steering Mechanism

Designed Multi-linkage steering mechanism and succeeded in satisfying Ackerman steering condition.

Extracted equations from the geometry and successfully simulated them using MATLAB software and determined the required quantities of the design.

Design of a Governor

Designed a governor to regulate the speed of an internal combustion engine.

It is designed such that the overshoot in response to a step input is less than 20 percent.

The 2 percent settling time in response to a step input is very small. For load disturbance input, the output is very insensitive.

Work Experience

Teaching Assistant, Heating, Ventilating and Air Conditioning (HVAC), SIUE May 2015 – July 2015

Prepared presentations on HVAC systems and communicated findings to peers and faculty.

Assisted students as and when encountered with difficulties in understanding duct sizing, CFM calculations and cost analysis.

Responsible for creating design drawings and identifying design flaws of HVAC systems in Engineering building at SIUE using AutoCAD.

Research Assistant, Shale Gas Hydraulic Fracturing Technology, SIUE July 2015 – April 2016

Provided research support by analyzing data and conducting experiments.

Investigated different geological locations for their properties and shale locations.

Simulated the stratigraphic models and succeeded in determining the upward chemical movement.

Intern, Hussmann Corporation – Bridgeton, Missouri July 2015 – Dec 2015

Designed and tested self-contained refrigerated cases using Solid-works and AutoCAD.

Assisted development and maintenance of the parts catalogs, owner’s manuals and operational instruction manuals for the assigned products and fixed BOMs and design issues.

Maintained correct part revisions in Windchill as Product Lifecycle Management for the parts and communicated with manufacturing unit.

Intern, Visakhapatnam Steel Plant Ltd, India June 2012 – Nov 2012

Studied and analyzed machine components present in light medium merchant mill department.

Prepared worksheets and scheduled manufacturing process and meetings with management.

Developed cost estimations for new products by specific pricing information from vendors.

Technical Skills

Software Solid-works, ANSYS, Revit, AutoCAD, Pro-E, MS Office, Adobe Photoshop, MS Excel

Analytical Software MATLAB (Basic Level)

Contact this candidate