Power Plant Software

Dale D. Hedge

Phone: 765-***-**** Email: ********@*****.*** Address: 3358 Wunder Ave

Cincinnati, Ohio 45211

Education: A.S. General Studies Vincennes University

A.A.S. & B.S. Mechanical Engineering Technology Purdue University

Work History:

February 2014- September 2015 Siemens Cincinnati, OH Senior Designer

Designed components for large industrial motors using parametric methods primarily Unigraphics NX9 using sketcher. Also used the assemblies package. Software used was Unigraphics NX9.

July 2013- November 2013 DRS Cincinnati, OH Senior Designer

Designed components for semi-trailer using parametric methods primarily Unigraphics NX8 using sketcher. Software used was Unigraphics NX8.

July 2011- April 2013 Belcan Cincinnati, OH Senior Designer

Designed components for aircraft seating using parametric methods primarily Unigraphics NX7 using sketcher. In addition designed wiring harnesses using bridge curves .Also used the assemblies package and used part families. Software used was Unigraphics NX7.

December 2010 - July 2011 Donaldson Bloomington, MN CAD Designer

Designed components for gas turbine filtration equipment using parametric methods primarily Unigraphics NX6 using sketcher. In addition designed wiring harnesses using bridge curves .Also used the assemblies package and used part families. Software used was Unigraphics NX6.

May 2008 - April 2010 Navistar Fort Wayne, IN CAD Designer

Designed components for truck steering using parametric methods primarily using sketcher. In addition did layouts to check clearances at different turn angles. Worked in body on military vehicles. Also used the assemblies package. Software used was Unigraphics NX4.

December 2007 - April 2008 AAI Corporation Hunt Valley, MD CAD Designer

Designed components for unmanned aircraft using parametric methods primarily using sketcher. In addition designed wiring harnesses using bridge curves. Also used the assemblies package. Software used was Unigraphics NX3.

July 2007 - October 2007 BE Aerospace Winston-Salem, NC CAD Design Engineer

Designed seating and components for commercial aircraft using parametric methods primarily using sketcher. In addition designed wiring harnesses using bridge curves. Also used the assemblies package. Software used was Unigraphics NX2.

June 2006 - March 2007 Rockwell-Collins San Jose, CA CAD Designer

Designed packaging for electronic components for heads up displays for military aircraft using parametric methods primarily using sketcher. In addition designed wiring harnesses using bridge curves. Also used the assemblies package. Software used was Unigraphics NX2.

July 2005 – November 2005 CDI Indianapolis, Indiana CAD Designer

Designed gas turbine parts using parametric methods primarily using sketcher. Also used the assemblies package. Software used was Unigraphics NX2.

January 2005 - June 2005 Curtiss-Wright Gastonia, NC CAD Designer

Designed parts and assemblies for a canopy mechanism for an F-18 Super Hornet. Used parametric methods in creating solid models. Also assisted in design of cargo door for new Boeing airliner. Used Unigraphics NX2 software.

October 2004 - December 2004 Ingersoll-Rand Southern Pines, NC CAD Designer

Designed parts and assemblies for small hand held power tools. Used Unigraphics NX2 software.

March 2004 - September 2004 GE Power Systems Greenville, SC CAD Designer

Designed compressor casings (castings and machined) for large gas turbines. Used Unigraphics version 18.

October 2003 - March 2004 Northrup-Grumman Baltimore, MD CAD Designer

Designed radar systems and other electronic devices used by the military aircraft. Used Unigraphics version 18.

July 2002 - July 2003 Rolls-Royce Gas Turbine Indianapolis, IN CAD Designer

Layout design of combustor unit for F-136 engine. Later worked on the design of lift fan for the Joint Strike Fighter. Used Unigraphics version 18.

January 2001 - December 2001 GE Aircraft Engines Cincinnati, OH CAD Designerreferences on

Worked on the upgrade of F-16 power plant. Designed compressor components for various military projects. Used Unigraphics version 18.

March 1989 - December 2000 GM Truck Group Pontiac, MI CAD Designer

Worked on various truck models designing brakes and other components for the chassis group. Used Unigraphics software.

Have additional automotive, aerospace and consumer electronics experience. Will supply request.

Contact this candidate