Electrical Technician
Resume:
FELIX MAC
*** *. *********** ******, **** Wayne, IN 46803
**********@*****.***
PROFESSIONAL SUMMARY
Demonstrated achiever with exceptional knowledge of Electronic and Electrical skills
Skilled at learning new concepts quickly, working well under pressure, and communicating ideas clearly and effectively.
Extensive Electronics and Industrial Maintenance skills, including knowledge of multiple circuitry environments and commercial networking communications.
Enthusiastic and experienced in Quality Control for Electrical and Mechanical troubleshooting.
EDUCATION
B.S., Industrial Engineering
ITT Technical Institute, Fort Wayne, IN
A.S., Electronics Engineering Technology
ITT Technical Institute, Fort Wayne, IN
Indiana State ESCO Electrical Certification
ELECTRICAL / ELECTRICAL CAREER HISTORY & ACCOMPLISHMENTS
ATS Electronic/ Electrical Technician 1/2015
Troubleshooting electronic and electrical controls Photoeyes, PLC, Relays, Proxy
Switches, Hydraulics, and Pneumatics. 24V, 120V, 220, 480 systems. And Automated Panel.
Electrical Assembly Technician Terex Advanced Mixer 3/2013 7/2014
Installed electrical systems for Allison transmissions.
Wiring electrical systems for Cummins engines such as; engines, engine harness, starter battery harness.
Computer modules, valve assembly, relay harnesses, low/high coolant module, starter relay
Electric panel, proximity switch, amp breakers, junction box
Assembly of Pneumatic air systems for operating brakes, cab air, hydraulic pressure hoses, Battery boxes
Final Assembly Testing
Reliability Tester, Manpower Contractor(Kimball Electric, Regal Beloit)
2/2012 2/2013 (contract)
Separated and disconnected motors from controller to isolate the failures
Maintained HIPOT and resistance through analysis of controller IF failures caused by phase-to-phase shorts from overheating mechanical Low Voltage Pre-test using an oscilloscope with a 40V DC power supply (current-limited to 1A) applied to the unit's line voltage inputs
Tested PC equipment with ECM programming module utilizing ECM Tool software to perform the "Cable Test" and "Opto Test" for verification in "test mode" to operate the motor electrically
Performed Line- Voltage tests by connecting the controller or controller/motor to a ICM-2 test box with correct line voltage verifying the motor operates properly at each programmed tap speed or PWM input control
Troubleshot component- level of failed control modules found during quality control screening
Electrical Assembly Technician, Micromatic Contractor(Staffmark)
10/2010 12/2011 (contract)
Held key responsibility of assembly electrical /electronic components; such as, Photoeyes, Servo motors, PLC, power, Relay switches, Proxy switches, Ozzie bus, Hydraulic, and Pneumatic.
Used schematics for 24V,110V,220V,480,testing and Input/Output Controls
Initiated final testing for Automated Manufacturing panels
Test Technician, Raytheon Contractor(Fountain Group)
Performed boundary scan functional acceptance tests
Utilized processor controlled testing environments
Interpreted and measured test results in Linux
Provided Troubleshooting for bad NCP and BCP processors
Repaired NCP and BCP circuit board components
Systems Tester, MTC ( 1/2008 5/2009 (contract)
Utilized Reverse Technology of Sony Playstation III systems for disassembling
Initialized testing of Sony Playstations and equipment
Produced Sony software on BlueRay hard drive system
Electronic Tech, Delphi Electronics 8/2004 10/2004 (contract)
Performed technical testing with RS-232 on 2007 GM automobiles such as Pontiac and Chevrolet.
Converted transmission and engine standards from Japan to U.S. standards
Troubleshot any problems found in the system and test down component level or board level
Bench Tech, Custom Radio Corporation 7/2003 12/2004
Performed technical tests and experiments on radio, CD players, VCPS and warranty equipment received
Repaired radios by testing radios with oscilloscopes, multi-meters and other test equipment down to board or component level
Soldered new component parts to specifications from schematics provided
Performed electrical and mechanical troubleshooting to determine issues
TECHNICAL SKILLS
• Robotics. Pneumatics, hydraulics
• Process Control
• Digital, Data & Network Communications
• Modern Wireless Communications Systems
• Electronic Circuit Design
• Communications Cabling
• Advanced Circuit Analysis
• A/C Electronics
• Solid State electronics
• Digital/Analog electronics
• Microprocessors
• Allen Bradley PLC 500
• Microcomputer principles
• OP amps
Contact this candidate