Technician Field Service

Clinton S. Lurvey

** **** **

Milton NH *****

Tel.# 603-***-****

Skills

Ability to use Spectrum Analyzers, DMM’s, dBm meters, Oscilloscopes, Frequency Generators,

Frequency Counters and other bench equipment to help design, troubleshoot and develop test

prototypes

Ability to read schematics and follow directions and procedures with minimal supervision

Good working knowledge of Electronic Components such as discrete transistors, FETs, TTL,

CMOS, OP Amps, FPGA and Multiplexed electronic circuits

Extensive knowledge of A.C. To D.C. And D.C. To D.C. Converters, Switching power supplies,

Automated Testers and Power Systems

Experienced with RF Amplifiers: Class A, B, AB and C

Strong component level Analog Electronics troubleshooting skills

Strong Computer Skill, Operating Systems and Networking Protocols

Experience

Analogic: Peabody, MA 05/2014-09/2014 (Temp Position)

Electronics Technician

Serve as engineering aide in the development of Rapid DNA scanning devices

Responsible for all PID loop controller tuning

In-depth experience with Pelletier Effect Thermal Electric cooling devices

In-depth experience troubleshooting of pneumatic and process control devices

In-depth experience troubleshooting FPGA and microprocessor devices

Experienced with BOM and Agile

Test and troubleshoot to the component level all PCBs used in scanning device

SANMINA CORP.: Derry, NH 2010 - 2014

Electronics Technician

Test and troubleshoot to the component level RF rubidium based frequency standards

Troubleshoot to the component level several rubidium based time bases. (Atomic Clocks)

Used DMMs, Frequency Counters, Oscilloscopes and H.P. Spectrum Analyzers

Troubleshoot a wide variety of frequency and timing standards used in the Telecom Industry

5s and Lean Team Leader

Group Leader for a Specific Product Line

RMA Repair Technician for several product lines.

Troubleshooting to the component level

Vicor Corp.: Andover, MA 1996 - 2008

Senior Test Engineering AIDE

Designed and prototyping of new Test Fixtures and Automated Testers

Troubleshot and optimized new Automated Testers

Evaluated and characterized new Universal Test Fixtures

Generated data sheets and application notes for Test Engineering laboratory data

Researched and tested new circuits and components which work with next Gen and V•I Chips at

Automated Test level

Performed Automated Test level testing on Power supplies implemented with V•I Chips

Troubleshot and optimized customer systems which use V•I Chips

Maintained and released BOMs (Bill of Materials) for new Automated Testers and reference

designs

Built prototype test fixtures and circuits for new testers and perform initial testing and

evaluation to validate new designs against the schematic and PCB layout

Kept accurate records of the results of experiments, troubleshooting and testing performed on

the Automated Testers and utilize this data to improve the design and utility of the Test

Engineering tools and products

Designed a burn-in chamber for Vicor's AIM module

Appointed responsibility for WEB page design and maintenance for all Automated Testers

Appointed responsibility for the maintenance and calibration of all test equipment assigned to

Test Engineering Department

Sears and Roebuck: Lewiston, ME 1991 – 1996

Consumer Electronics Repair Technician

Repaired VCRs, Television sets, projection TVs and computers

Worked as a road tech for 3 years with much customer contact

Component level troubleshooting

General Electric Company: Wilmington, MA 1979 – 1990

Quality Assurance Supervisor

Supervised 68 inspectors and test technicians

Worked with DCAS and many Mil Specs

Worked as an electronics technician

Worked with many aircraft cockpit display systems including Navigational Gyros

Reduced Hi-Pot reject rate of Rockwell B-1B Aircraft Vertical Tape Indicator Torquer Motor

windings from 50 % to less than 5%

Served as Team Leader for internal Audits before DCAS presentations

Data Precision Corp.: Danvers, MA 1976 - 1979

Assistant Field Service Manager

Supervised the activities of 12 Field Service personal in a high volume repair business

Responsible for the shop budgeting and capital equipment expenses

Interacted with customers daily

Maintained a 3- to 5-day turn-around of all field returns

Education:

Eastern Maine Technical College - A/S

Massachusetts Institute of Technology - Diploma

General Electric Front Line Supervision - Diploma

Lynn English High School, Industrial Electronics - Diploma

Contact this candidate