Rocky Mount, NC *****
252-***-**** Cell
acgg3v@r.postjobfree.com
Shaun J. Weisphal
Objective
Career with advancement potential
Experience
****-**** ****** ********* & Ford Auburn, ME
Diesel Mechanic
PMI’s on trucks - Oil changes, grease jobs, inspect under carriage, change filters (oil, fuel, air)
Check for oil leaks on transmission, engine, & differentials
Checked and replaced brakes
Repaired trucks in shop and on lot
Cleaned up shop after each repair
Ordered parts
Test drove trucks to determine problem
Replaced transmissions, differentials, air compressors, turbo, and lights on trucks.
Replaced hydraulic cylinders, hoses, patched floor and walls of body
Trouble shoot, rewired truck and body for lights, limit switches, and controls
Test drove trucks after repairs
2012-2013 Republic Services Durham, NC
Diesel Mechanic
PMI’s on trucks - Oil changes, grease jobs, inspect under carriage, change filters (oil, fuel, air)
Check for oil leaks on transmission, engine, & differentials
Checked and replaced brakes
Change tires
Repaired trucks on the road and in shop
Replaced transmissions, differentials, air compressors, turbo, and lights on trucks.
Replaced hydraulic cylinders, hoses, patched floor and walls of body
Trouble shoot, rewired truck and body for lights, limit switches, PLC, and operating controls
2011-2012 C.R. England Global Transportation Salt Lake City, UT
OTR T/T Driver
Drove solo OTR.
Drive tractor trailer to shipper site to pick up freight and then to destination.
Backed trailers in all different types of docks ally to open area warehouse.
Swap trailers with other drivers to make sure load is delivered on time.
Use GPS & road maps to find most accurate route to get from one point to another.
Pulled 53’ trailers with reefer on front of trailer.
Make sure trailer is clean & temp on reefer loads is set right.
After trailer is loaded weigh the T/T to make sure it is not over weight on any of the axles.
Steer axle- 12,000 lbs. Tractor tandems- 34,000 lbs. Trailer tandems- 34,000 lbs.
Put trailer axles as close as can be to the most restrictive state’s rules that I was going to travel through.
Pulp the load when needed to make sure I was not going to have bad product when I delivered.
Do pretrip & post-trip inspections on truck and trailer daily.
2007- 2011 Gregory Poole Equipment Co. Raleigh, NC
Field Service Technician II
Drive & maintain service van (clean, maintain stock, and all repairs to truck)
PMI’s and repairs on all brands of forklifts, man lifts, Yard trucks, and scrubber/sweepers(Gas & Electric powered)
PMI & repairs to Shuttlewagons at customers with rail cars on lot (like CSX)
PMs- oil changes, grease jobs, blow out equipment, safety inspection, change filters(oil, fuel, air, hydraulic, transmission)
Repairs on Electric trucks (24-48 volt systems) Gas trucks (propane, gas, and diesel engines)
Check for oil leaks on transmission, engine, hydraulic hoses, and differentials
Checked and replaced brakes
Rebuilt and Replaced hydraulic cylinders, hoses
Change solid tires on and off rims with tire press
Repair equipment at customer site and in shop
Order parts for every PM & repairs I do
Test drive equipment to determine problem & after repair
Trouble shoot, rewired equipment and lights, limit switches, PLC, and operating controls
Fabricated a hydraulic system for a rail wheel lift attachment
2005-2006 Stock Building Supply Wilson, NC
Industrial Maintenance Mechanic
Replace air lines and air fittings on machines
Fabricate metal tables, carts and racks to be used in-house and sold to sister stores
Reuse and recycle equipment
Trouble shoot electrical and mechanical parts of machine
Replaced electric motors, fuses, starters, timers, relays, and safety switches
Replace routers, router bits, and drill bits on door machines
General plant maintenance (replace/repair lights, install exit signs)
Repaired air guns
Did PMI’s on forklifts, saws, door handles, door machines and strike jamb machine
2001-2005 Waste Management Selma, NC
Diesel Mechanic
PMI’s on trucks - Oil changes, grease jobs, inspect under carriage, change filters (oil, fuel, air)
Check for oil leaks on transmission, engine, & differentials
Checked and replaced brakes
Change tires on and off rims
Repaired trucks on the road and in shop
Cleaned up oil spills on roadways from hydraulic hoses bursting
Ordered parts
Test drove trucks to determine problem
Replaced transmissions, differentials, air compressors, turbo, and lights on trucks.
Replaced hydraulic cylinders, hoses, patched floor and walls of body
Trouble shoot, rewired truck and body for lights, limit switches, PLC, and operating controls
Transported removed and installed trash compactors at area plants.
PMI’s on all compactors and balers. Greased, changed oil, repaired, trouble shoot, & cleaned out behind blade.
Install control wiring and breaker box.
2000-2001 Speedo Inc. Kenly, NC
Lube Technician
Do PMI’s on tractor-trailers, light trucks, RVs and straight trucks
Oil changes & grease jobs the way the driver requested
Cleaning the pit & draining the waste oil.
1999-2000 Electrical Services Limited Wilson, NC
Electrician’s Helper
Helped to wire lights, switches, outlets, motors, fuse boxes, breaker boxes, pull wire, run conduit, & PVC pipe
Education
1999 Johnston Community College Smithfield, NC
NC Truck Driver Training School
Licenses
Class A CDL
Training
McNeilus Truck Bodies
Front Loader Class
Rear Loader Class
Auto Reach Class
Marathon Equipment Company
RAM-JET Compactor and Vertical Balers
Waste Management
Heavy Duty Truck Brake Inspector
Preventative Maintenance Inspection
Gregory Poole Equipment Co.
Fork lift PMI
Advance Scrubbers/Sweepers
Shaun J Weisphal, 301 Oakdale Rd. Rocky Mount, NC