Mechanical Customer
Resume:
Mark T Quirk II
Orlando, FL, 32809
Summary:
Experienced Electro and Mechanical assembler/ Fiber Optic Technician/ Test Technician
looking for full time work. Experience with ESD practices and Cleanroom assembly
methods. Optical bonding and thermal testing of sub / final products used in the
manufacturing of Infrared and Thermal Laser Range Finding equipment. Experience in
Hand on Installation of Fiber optics, Hyperbaric Testing of Fiber Optics and
troubleshooting of Fiber optic issues. Laser Assembler/ Tester.
Superior Technical Resources
Orlando, FL
July 2014 to September 2014
Position: Electro Mechanical Assembly/Laser Assembly/ Optical Assembly/ Test
Hired as a temporary D.O.D. contractor to build various electro mechanical assemblies,
Lasers, bonding and laser aligning optics for L3 ALST Communications. Assemble
various eye safe and non eye safe laser products from base level housings to upper level
complete systems. Installation of various lasers into Laser Range Guidance Systems.
Installation of various wire harness/ cable assemblies into various sub assemblies/ final
product. Bonding of various optics into various optical sub assemblies. Laser alignment of
various optics on Norland optical testing equipment with Class 3B Henney Lasers. Use of
various adhesives pre mixed and self measured mixed chemical bonding compounds with
measurements of chemical mixture on various scales to mix two part epoxies. Injection of
bonding compounds by 3ml hand syringes and EFD foot pump by hand, activated
pressurized adhesive machine. Bonding of optics by hand, under microscope, on laser
assisted optical balancing test equipment. Installation of various gasket and o rings on
optics and electro mechanical assemblies to help ensure functionaloity of unit under test
under nitrogen filled leak check test equipment. Troubleshooting / Re working of various
wire harness applications, fixing wires, crimps, connectors. Re working Optics, Debonding
multiple optics with hot plates, heat guns, chemical compounds.
TRC Staffing Inc.
S.Daytona, Florida
Position: Senior Fiber Optic Technician
01/04/2014 to 4/3/2014
Hired as a temporary employee to assemble and test various fiber optic products for
Teledyne Oil & Gas. Assembly of various fiber optic stem assemblies. Use of time and
heat curing epoxies to bond ceramic ferrules into peek and titanium stems. Using various
fixtures for small heat curing ovens. Verifying proper placement of ferrule into stems with a
go no go fixture mesuring total length of product in tenthousandths. Verification of proper
placement dimensionally with a T.I.R. test measuring spherical dimensioning of stem in
tenthousandths. Pull test of ferrule and stems to check durability of epoxying process with
a 10% of batch test.Placement of fiber optics 250 micron and 900 micron sized into stem
assemblies, bonding of fibers to stems with 24hr heat/ time curing epoxies. Use of Norland
Test Equipment to conduct concentricity testing to verify spherical heights of fiber. Use of
Norland Interferometer to verify spherical dimensioning, fiber height, fiber surfacing,
geometrical dimensioning of fiber structure to verify x,y and z axis to show center of stem.
Machine and hand polishing of various fiber optic assemblies and products. Hyperbaric
Testing of stems, ferrules, and fiber optics from 1500psi to 10,000psi. Using Omega
meters, JGR GMS testing equipment and Autotank software programs. Cutting of various
guage teflon jumpers cables/ hoses to appropriate lengths. Removal of inner strands of
fiber and rubber to expose teflon strands of wrap before inner layer of hose Hose prep.
Installation of various boot seals, and titanium and braised titanium connectors for sub sea
assemblies. Pulling of fiber optics,250 micron, and 900 micron guage fibers from 5 feet
long to over 300ft long thru jumper hoses and prepping fiber optic ends to various strip
lengths for various sub sea applications. Troubleshooting various IL and RL reading issues
with various grit polishing papers, lasers, index matching gel, dow and corning oil, Agilent
multimeters, Agilent powermeters, O.T.D.R.(optical time domain reflectance). All worked
performed to company and customer blueprints/schematics. Company ISO certified
TRC Staffing Inc.
S. Daytona, Florida
Position: Electro mechanical Assembler
06/07/2013 to 11/16/2013.
Hired as a temporary employee to perform electro mechanical assemblies for RAYDON.
Assemble, various products to customer and company specifications/ Blueprints/Wiring
Diagrams. Soldering of wires to pc boards and connectors. Manufacturing of cables with
multiple connectors. Use of hand tools to crimp various size pins male and female for
various connector types. Mechanical assemblies, and electro mechanical assemblies.
Building of test cabinets and computerized work stations. Installation of various wires,
mechanical and electric/ computerized pieces into finished computerized work stations.
Re work of finished customer products, to updated company versions. Packing out
finished products, onto pallets. Use of label making machines and label making systems.
Making barcode labels for various assemblies. ESD Trained. Workmanship to ISO
standards. In House Raydon certificates for IPC 610, IPC WHMA 620 and JSTD 001
soldering available for review.
Adecco Staffing
Melbourne Florida
Position: Solderer/Mechanical Assembler
09/2012 to 04/2013
Contract temporary worker hired as an assembler to work at Quality Electronics
Manufacturing in Melbourne Florida. Cut wire and heavy cables to customer and QEM
specifications to be used in various wire harnesses, daisy chains and cable installations.
Wire box built cabinets according to wiring diagrams and schematics. Trained on soldering
techniques for J Hook, Lap solder and dipping of wire leads. Attach wire leads to PC
boards. J STD 001 and IPC Class 2 soldering skills. Move heavy laden pallets of
assemblies, raw parts and wire / cable spools with use of pallet jacks.
SRI HERMETICS
Melbourne, FL.
Jan 2012 to March 2012
Job Duties: Assemble various products to customer and company requirements. Solder
cables, wires, pins, connectors to CCA and PC Board assemblies. Hand Solder, use of
Lapel Soldering machines. Solder dipping of pins wires and connectors. Mixing and
installing Hermetic sealant around pins and connectors and PC Boards inside of Moldings.
Use of thermal convection ovens that range from near room temperature to up in excess
of 600 degrees Celsius. Wire cutting with Schulienger Cutting Machine, hand cutters and
strippers. Hand crimping of pins to wires, install sleeving on to wire and cable applications.
Sintering of pins on hotplate, including Nano. Use of various chemicals daily, such as,
Nitric Acid, DMK, Methanol, and Toluene...etc., Use of ESD wrist straps and grounds.
Sand and Glass bead blasting with 80 and 120 grit of pins, connectors and other various
products. Micro blasting with 240 and 320 grit sand and glass of Nano pins, Nano
connectors and other various Nano products. Soldering was performed under various
Microscopes from 1x to 40x magnification. Self Inspection from parts blue print schematics
and customer/ company size and quality requirements, before parts can be moved.
Superior Technical Resources/ DRS Optronics
Melbourne, Fl
Position: Laser Assy./ Test
July 2011 to Dec 2011
Electro / Mechanical Assembler
Job Duties: Assemble, and balance optics, optical coating. Mechanical assembly, electro
mechanical assembly of Lasers and Other DRS Products, environmental testing with
Thermotron chambers. PC board and circuit board testing/ assembly, wire and cable
assembly/testing. Building of connectors. Assembly of pins to connectors. Bonding of laser
optics and such with variations of UV light, temperature and time curing chemicals.
Chemical cleansing of optics, mechanical assemblies, electro mechanical assemblies, and
other DRS products. Self inspection of all assembled products beforecomputer system, or
inside of the facility to Inspection area. ESD trained and cert., ISO 9001 and J STD
trained for proper Assembly / test procedures within company and customer guidelines.
Use of Microsoft software daily. Produce spreadsheets for documentation of product build
and product testing results with MS Excel. Data Matrix programming for scanners and
spreadsheets alike. Torque testing of pneumatic hand tools daily to verify strength of
drivers for assembly per customer and company regulations. Documentation of torque
testing daily into computer spreadsheets for Government Auditors to review daily.
TRC Staffing Services
Melbourne, Florida
Duties: Assembly, Test and Self Inspection
12/2010 to 4/2/2011
Assemble and Test CCA's and PC Boards for Mack Technologies. Diversified Workplace.
Solder components and wires to CCA's and PC Boards. Electronically test CCA's and PC
Boards to test functionality of circuit card and PC Board. Reprogramming of CCA's and PC
Boards for defective materials. Inspect assemblies for any defects in workmanship to
IPC610 A REV D requirements. All testing done to company and customer requirements
of IPC 610 A REV D and JSTD 0001. Verify component placement on CCA's and PC
Boards per documentation/ Print requirements. Segregate Non conforming materials with
defect tags and SFDM. Work performed on 2nd shift.
Manpower Contract Agency
Melbourne, Florida
Position: Laser Assembler/Tester. Optical Bonding
March 2010 to Nov 2010
Temporary Contract worker DRS Technologies in Palm Bay and Melbourne Florida.
Assemble and test various Laser and Electro Mechanical products produced by DRS
Technologies, Use Pneumatic tools, Wrenches, screw drivers and ball drivers to assemble
parts to Prints and Process Plans. Assemble and Test products in a Clean Room
Environment. Bonding of various optics per assembly process plans. Scan assemblies into
Excel database for tracking of serial numbers. Load and unload Thermal chambers for
Environmental test in Thermotron chambers. Operate 3800, 7800 and 8800 controllers on
Thermotron Chambers. Test and inspect assemblies to Test Procedures. Inspect units for
and visual defects. Log results manually and into Excel spread sheets. Use of computer
work stations with Outlook 2007 and Microsoft Office 2007 to complete tasks. Transact
parts and assemblies in Oracle Database. Log any failures into DRS NRS database and
segregate non conforming materials from production units. Verify workmanship of
assemblies built in various areas of the factory. Diversified Workplace. ESD Trained and
Certified. DRS at this time is an AS 9100 / ISO 9001 Company.
Budget Restaurant Supplies
Commerce Parkway
Orlando, Fl
Position: General Laborer
Jan 2009 to Nov 2009
General warehouse laborer for wholesale restaurant Supply Company.
Load and unload trucks with fork truck, hand jacks and dolly’s.
Use various power tools to assemble a variety of equipment used in commercial
applications of the food service industry. (Ovens, mixers, racks, chairs, tables and walk in
refrigeration systems.
Phil Hughes General Maintenance
Holopaw, Florida
October 2007 to September 2008
Work for General Building Contractor as a Laborer.
Taught how to fix and replace Interior surfaces in various restaurants and local
establishments. Use power drills, sanders, grinders, table saws, sawz alls, and power
washers. Paint walls, wash walls, remove and replace floor tiles.
Limited repairs of AC units and duct work on heating and air ventilation.
Lift various objects up to 100 pounds. Hours vary depending on project for that day or
night.
Rainbow Trucking / North American Van Lines
N. Attleboro / Franklin, Massachusetts
Jan 2007 to May 2007
Warehousing and Transportation
Moving and Storage business.
Load and unload various items from household goods to Industrial machines to various
points in the eastern portion of the USA. Ship & Pack items in boxes. Use hand trucks and
dollies to move items from Tractor Trailers to homes and businesses. Familiar with
Microsoft Windows 98 and Office 2000 software. Out of state and in state mover.
Manpower Contract Agency
Melbourne Fl
Position: Laser Assy./ Test
Feb 2006 to Dec 2006
Temporary Employment Agency.
Assemble and test various Laser products at local factories such as DRS Optronics in
Palm Bay. Follow written and verbal instructions to Assemble various products produced
at DRS Optronics, such as BELRF, and ALP, both Laser systems. Use of epoxy to bond
various optical lenses to various electro mechanical assemblies. Testing of movement of
optical lenses to ensure functionality of finished product before laser testing. ESD trained.
Use protective gloves for optical and laser assemblies. ISO 9000/9002 Awareness.
Education:
GED obtained in June of 2006.
I am authorized to work anywhere in the United States.
I am a US Citizen.
Contact this candidate