Project Human Resources
Resume:
Yancell Howell R. Teodoro
Dela Costa *, Subd., Montalban Rizal (Philippines)
Phone No.: (02) 3680871
Mobile No.: (091*-***-****
E-mail add : **************@*****.***
Career Objective : To obtain a position in a company that will enable me to use,
maximize and enhance my welding and people skills.
PERSONAL INFORMATION
Birthdate : January 2, 1978
Birth Place : Orion Bataan
Height : 5’11” ft.
Weight : 185 lbs.
Sex : Male
Civil Status : Married
Religion : Catholic
Nationality : Filipino
EDUCATIONAL BACKGROUND
Elementary Year [From] -
[To]
School: Orion Bataan Elementary School 1984 - 1990
Address: Orion Bataan
Secondary
School: Colegio de San Pascual Baylon 1990 - 1994
Address: Obando Bulacan
EMPLOYMENT HISTORY
DAEWOO E&C CO.
Professional Experience : TIG WELDER (STAINLESS STEEL PIPE)
Project : PNG-LNG Project
Contractor : CHIYODA – JGC Joint Venture
Location : Papua New Guinea
Period : December 9, 2011 - January 15,2014
JOB RESPONSIBILITIES :
• Responsible in fitting – up and welding any kind of pipe (small bore to big bore).
• Responsibility in pre-heating, post heating, stress relieving and verification of
carbon steel, low alloy and stainless steel.
• Responsible in reviewing and preparing piping materials.
• Ensure compliance in Applicable Welding procedures.
• Familiarized with all production in Welding position for plate and pipe (Flat
Position.)
• Prepare parameter Report used before Weld.
• Responsible in fitting –up and alignment in ensure the Gap (minimum
requirement -1.5 mm Gap tolerance).
MAYER STEEL CORPORATION
Professional Experience : PIPE WELDER
Location : Philippines
Period : April 20 - August 12, 2010
JOB RESPONSIBILITIES :
• Responsible in fitting – up and welding any kind of pipe (small bore to big bore).
• Responsibility in pre-heating, post heating, stress relieving and verification of
carbon steel, low alloy and stainless steel.
• Responsible in reviewing and preparing piping materials.
• Ensure compliance in Applicable Welding procedures.
• Familiarized with all production in Welding position for plate and pipe (Flat
Position.)
• Horizontal Position, Vertical Position and Overhead Position).
• To Weld of 24 “ Diameter Pipe Material A321 – TP304 using Filler ER308L from
Water Injection Pump.
• Responsible in following the standards in repairing of defect such as pin hole,
excessive concavity, spatter and cracks.
• Responsible in checking the Standard procedure of WPQR and specification.
• Responsible in submitting technical data sheet production to foreman to inspect
for completeness and testing of piping system.
• Responsible in preparation and submission of sketches such as – built drawing to
Supervisor for listing through Isometric drawing.
GAMA EEI
Professional Experience : TIG WELDER ALLOY
Project : QCS – QG 3 & 4 PROJECT
Location : Qatar
Period : March 12, 2009 - March 12, 2010
JOB RESPONSIBILITIES :
• Responsible in alignment and fitting –up prior to weld using electrode and filler
from carbon to alloy steel.
• Responsible in air blowing of pipe and inspection before erection.
• Flange face to Ensure Fit – Alignment to be done.
• Conduct and prepare parameter report used before weld.
• Responsible in cutting and welding joint in suspected defect.
• Big Bore Pipe Repair to used (R316T15 Filler ) as AWS Specification.
• To weld Heavy Wall pipe Alloy using E-8018
• PWHT Required before Weld of alloy Steel.
• Fit –up and Alignment to Ensure the Gap was Minimum Requirement (1.5 mm
Gap) Tolerance.
• Assuring all Electrode to used in Carbon Steel to oven with Requirement under
WPQR.
• Root Pass used (ER316L) for Weld Joint.
• Before Weld Dissimilar Joint list showing on Isometric Drawing.
• Duplex 2594 Filler used for Pipe Support ( Trunion Pipe Shoe Support, Pad
Support)
• Monitor Purge Inspection before weld.
• To check Correct Fit –up (1.5mm Approximately ) prior to Weld.
• Socket to Weld as per Gap Tolerance.
SAMSUNG ENGINEERING CONSTRUCTION
Professional Experience : TIG WELDER
Project : IBN ZAHR – OCT PROJECT
Location : Jubail Saudi Arabia
Period : January 20, 2007 - March 2, 2008
JOB RESPONSIBILITIES :
• Responsible in alignment and fitting –up to ensure that the gap was Minimum
Requirement (1.5 mm Gap) Tolerance.
• Carry –out 100% Weld for Approval of QC Inspector.
• Ensuring compliance in the standards for repairing of detect such as pin hole,
excessive concavity, spatter and cracks.
• Responsible in ensuring all electrode to used in carbon steel to oven following
requirements under WPQR.
• Before Weld Dissimilar joint list Showing on Isometric Drawing.
• Responsible in checking correct fit – up (1.5mm Approximately) prior to weld.
• Socket joint to Weld as per Gap Tolerance.
• Ensure compliance in follow the standard for repairing of defect such as pin hole,
excessive concavity, spatter and cracks.
• Responsible in checking and ensuring compliance on standard procedure of
WPQR and specification.
• Responsible in preparation of technical data sheet production and submit to
foreman for pipe system inspect ion and testing.
• Prepare sketches and submit - as built Drawing to Supervision for listing through
isometric drawing.
NASSER AL-HAJRI COMPANY
Professional Experience : TIG WELDER ALLOY
Project : AR RAZI METHANOL PLANT
Location : Jubail Saudi Arabia
Period : September 1, 2006 - October 23, 2007
JOB RESPONSIBILITIES :
• Responsible in alignment and fitting –up prior to weld using electrode and filler
from carbon to alloy steel.
• Responsible in air blowing pipe and inspection before rrection.
NASSER AL-HAJRI COMPANY
Professional Experience : TIG WELDER
Project : GULF FARABI N PARRAFIN PROJECT
Location : Jubail Saudi Arabia
Period : September 14, 2005 - October 12, 2006
JOB RESPONSIBILITIES :
• To fit – up and and weld of any kind of pipe from small bore to big bore.
• Pre Heating, Post Heating, Stress Relieving Activities and Verification, In
Carbon Steel, Low Alloy and Stainless Steel.
• Prepare Piping Materials Review to Assure that it Complies with the Applicable
Welding Procedure.
• Familiarized all Production in Welding position by Plate and Pipe (Flat Position.)
• Parameter Report used before Weld.
• Fit –up and Alignment to Ensure the Gap was Minimum Requirement (1.5 mm
Gap) Tolerance.
NASSER AL-HAJRI COMPANY
Professional Experience : TIG WELDER
Project : SABIC ACETIC ACID PROJECT
Location : Yanbu Saudi Arabia
Period : March 20, 2003 - March 21, 2005
JOB RESPONSIBILITIES :
• Root Pass used (ER316L) for Weld Joint.
• Before Weld Dissimilar Joint list showing on Isometric Drawing.
• Duplex 2594 Filler used for Pipe Support ( Trunion Pipe Shoe Support, Pad
Support)
• Monitor Purge Inspection before weld.
• To check Correct Fit –up (1.5mm Approximately ) prior to Weld.
• Socket to Weld as per Gap Tolerance.
• Familiarized all Production in Welding position by Plate and Pipe (Flat Position
Horizontal Position, Vertical Position and Overhead Position).
• Parameter report used before weld.
SPECIAL SKILLS / INTERESTS
• Skilled in major relevant computer applications like MS Word, Excel, Powerpoint
• Well-versed in oral and written English and Filipino.
CHARACTER REFERENCES
Alexander Bergajo
Tig Welder – Batangas City
Contact No. 091*-*******
Maybelle Santos
Human Resources
FNF – Chowking
Contact No. 092*-*******
Yancel Howell Teodoro
Reference and other supporting documents available upon request
Contact this candidate