Electrical Power Plant
Resume:
Romulo G. Maligalig
Brgy. Lamot * Calauan, Laguna
Email Add.:**************@*****.***
Contact No.: +63-966-***-****
POSITION DESIRED: ELECTRICAL TECHNICIAN
PERSONAL INFORMATION
Date of Birth : February 17, 1969
Place of Birth : Calauan, Laguna
Gender : Male
Civil Status : Single
Height : 5’3”
Weight : 137 lbs.
Citizenship : Filipino
Religion : Roman Catholic
Father’s Name : Jose C. Maligalig
Mother’s Name : Lydia C. Guevarra
Address : Brgy. Lamot 2, Calauan, Laguna
Language Spoken : English and Tagalog
Emergency Contact Person : Rodolfo G. Maligalig
Contact No. : +639**-***-****
EDUCATIONAL BACKGROUND
Tertiary : MFI Foundation, Incorporated
Advanced Industrial Motor Control
August 17, 2013 – October 5, 2013
Calamba Technical Institute
Electrical Technology
March 1988
Secondary : Liceo de Calauan
March 1986
Primary : Calauan Central School
March 1982
WORKING EXPERIENCE
•Electrical Technician SABIC IBN ZHAR
Jubail Saudi Arabia
December 2016 – February 2018
Duties and Responsibilities
•Received scheduled preventive and corrective maintenance job order form the supervisor of electrical equipment like electric motor rated voltage 380V 4.16 KV.
•Motor Control center brand Merlin Gerin, ABB, Schneider, Transformer Voltage rated 13.8 KV/4.16 KV.
•Perform greasing of motor as per electrical (SMP) Standard Maintenance Procedure, Test insulation resistance of motors, Tag-in Tag-out, Rack-in Rack-out of MCC and Switchgears 380V, 4.16 KV., disconnect and reconnect of power supply of motors.
•Opening and closing of work permit like cold, electrical and hot permit. Troubleshooting of MCC by analyzing the cause of failure to start of the motors and reset of MCC and VSD panel model altivar 71 plus/Schneider.
•Electrical Technician ACGC CO.
Al-Khobar, Saudi Arabia
November 28, 2013 – October 2016
Job Description
Make daily maintenance route of Electrical Machine on the facilities such as service filth panel Cathodic Panel, Converter, HVAC Motor Control Center (MCC) like Wyne Delta Control with PLC Control module, Install and commissioning of motor, replace Damage contactors, Timer Circuit Breaker, Jet Fuel Electric Control Panel overhaul Electric Motors for maintenance and repair wiring of motor control panel for sewage pumps and HVAC Units.
•Electrical Technician Kumyang Electric Co.
Abu Dhabi (Ruwais)
July 13, 2012 – July 29, 2013
Job Description
Measure Insulation Resistance and winding resistance of motor, Motor Control unit and power cables, for ground fault by used of test instrument such as MeggerMit 510/2 5KV-10KV / Insulation Resistance Tester, MeggerMit 230 Insulation / Continuity Tester, Fluke 87V ohm Tester and fluke 374 AC/DC Clamp meter to check phase current.
Glanding of armored cable size 4c x 25mm2, 7c x 2.5 mm2, 3c x 70mm2. Wiring and termination of control panel board in substation where location are Switch Gear Room, Satellite Instrument Shelter room (SIS) etc. Rectification of telecom wiring installation for grounded, shorted shield. Functional test of MCC mm 300 motor manager and motors installed on the oil and gas processing plant, operate Air Circuit Breaker. Received complete Lock-out / Tag-out and electrical safety procedures from the supervisor. Interpret Schematic Diagram.
•Electrical Technician System Factory for Electrical Panel
Saudi Arabia (Riyadh)
January 19, 2010 – February 25, 2012
Job Description
Install electrical apparatus like control relays, mcb, magnetic, space heater, terminal blocks in panel board the brands of electrical apparatus are Morsmith, Omron, Telemecanique, ABB, Schneider, Alen – Bradley, GE Electric, Siemens. Wiring and Termination of Control Panel, Distribution Board, Relay Panel, Switchgears, Low Voltage Panel, High Voltage Panel use in power Plant Substation. Do some wiring modification, test wires and cables for insulation Resistance by use of MeggerMit 510/2. Use Torqing tools for tightening bolts and nuts.
•Electrician UTS Kentz Co. LTD
Abu Dhabi UAE (Habshan)
February 9, 2008 – January 28, 2009
Job Description
IR Test of cable armored wire by used of MeggerMit 510/2 5KV-10KV/ insulation resistance test, for ground fault, check phase current by use of clamp meter model fluke 374 C/DC. Fabrication and installation of cable tray sixe 50,100,150mm. make wiring termination of electrical power and control panel board.
•Electrical Technician AL-RADDADI READY MIX CO.
Saudi Arabia (Madina)
November 21, 2005 – December 7, 2007
Job Description
Troubleshoot motor control ckt, such as DOL (direct on line), forward-reverse, jog control, wye-delta starter for open ckt. Change new contractors and overload, blown fuse and circuit breaker. Check grounded motors by use of multi tester model no. YX-360 TR. Change worn bearing of motor and install a new motor. Repair and installed automotive starter, solenoid relay, control relays, alternator and battery installation, wiring and troubleshoot automotive lighting crkt. Overhaul generator for cleaning and revarnish of windings.
Electrical Technician TOYO- INK COMPOUND CORP.
PHILIPPINES
November 25, 2001- August 30, 2005
JOB DESCRIPTION
Wiring and installation of motor control ckt. Like contactors, push buttons switch (start/stop) forward- reverse, wye- delta starter. Use phase sequences device to test correct phase, AC/DC clamp meter for reading phase current. Test insulation resistance of motors by use of megger. Make preventive maintenance of extruder machines, power tools in the plant by greasing of rotating parts, such as gear box, bearing tightening all electrical connection, cleaning motors, disassemble motor for repairs of bearings and replaced new one. Change battery and maintaining of good operation of generator. Received firefighting procedure and electrical safety from senior technician.
•Electrician Denki Technical Services, Inc
Philippines
July 11, 1996 – July 15, 2000
Job Description
Wiring and installation of lighting fixtures, power outlets, circuit breakers, motor control unit. Assembling and erection of electrical conduit, lay-out junction boxes based on electrical lay-out drawing. Bend Metal conduit size 1/2”, ”,1’1 ” in 90 degree bend and offset bend by use of hickey or pipe bender. Cable laying, cable termination by use of hydraulic crimper, wiring of three-way switch and fou-way switches. Wiring of single phase and three phase panels. Install seal off fittings like ESD, EYD for hazardous area like gasoline pump station.
I hereby certify that the above information is true and correct to the best of my knowledge and belief.
Romulo G. Maligalig
Applicant’s Signature
Contact this candidate