Engineer Software

SACHIN PATEL

*** ********* *****

Scarborough, ON M1H 2E7

Mob. No: 647-***-****

*****-***************@*****.***

CAREER OBJECTIVE

Looking for a job position in an organization that provides me an opportunity to explore my skills and knowledge.

PROFILE SUMMARY

Larsen & Toubro Limited, India Jan-2016 to Feb-2019

Switchgear Design & Development Center

Senior Development Engineer

Worked on following Low voltage circuit breaker & it’s accessories (power system protection devices)

MINI MCB, RCCB, RCBO & Auxiliary Devices (UV, OV, Shunt, AUX & AUX-TAC).

Experience of product certification testing.

Completed MINI MCB certification testing as per standard IEC 60898-1: 2015

Carried out in house testing of RCCB-IEC 61008 -1 & RCBO-IEC 61009-1

Catalogue Number booking, BOM creation, TCN & PCN creation using SAP.

3D part & drawing making using Creo 3D design software after considering ease of manufacturing feasibility

Fixture & Gauge Designing experience

Used geometric dimensioning & tolerancing in regular basis in component designing (GD&T)

Part of CFT team for product reliability improvement (Member of team Design, Quality & Engineering)

Working experience of all type of testing & measuring equipment used in industry/test lab like

Current source & Voltage source,

HV Tester, Impulse Tester, Continuity Tester, Torque Tester.

CRO & Multi Meter, Vernier caliper, Gauge measurement, Rapid I

Part of PCB redesign team of UV, OV & 100mA Adi type RCCB.

Cause identification which is responsible for failure, measuring input & output of PCB components using CRO & according to results of measurement decide next course of action.

Experience of Manual soldering (Done project on soldering improvement of PCB & successfully implemented on production line) also have deep knowledge of SMD & Through hole PCB components.

Identify Area of improvements in products in terms of process, money & quality.

Experience of total product manufacturing cycle starting from components manufacturing & quality checking to product manufacturing & product quality checking. (Process control, SOP, OPL, Cycle Time)

Major role is to identify cause of production line rejection & secondary operations reduction.

Knowledge of following tools to analyze problems: Applicable for all type of manufacturing industry

Fishbone (cause & effect) diagram,

Six sigma green belt (7 QC tools),

PDCA cycle (Plan DO Check & Action),

Shinin DoE,

FMEA Cycle,

Validation of Temporary change note (TCN) & according to make Permanent change note (PCN).

Testing coordination of pilot batch with PCN & release improvement note (Technical Writing).

Robert Bosch Engineering, India Aug-2015 to Jan-2016

Drive Assistant RDAR Group

Associate Software Engineer

Part of System diagnostic unit (SDU) team.

Initial level Knowledge of coding, Testing &Troubleshooting in coding.

Configuration of input & output signals.

PROJECT HANDELED

Design improvement in existing range of Residual current circuit Breaker (RCCB) of rating

(In=16A to 100A & In=10mA to 300mA) of AC & Adi Type.

Design improvement in existing range of Residual Current Circuit Breaker with over load protection (RCBO) rating is (In=6A to 40A, In=10mA to 300mA & Icn=10kA) of AC & Adi Type.

Achievements:-

FTY improve avg. from 80% to 97%.

Reliability failure improve from 40% to Zero -Quantum leap award.

Test button failure reduce 4% to zero -Star team award.

PMR calibration & Trip level rejection reduce 10% to 3 %.

Part of design team of MINI MCB operated as a switch (In=6A to 32A & Icn=3kA).

Achievements:-

Establish and validate thermal calibration and verification band of all ratings.

Improve Short circuit behavior of product with number of trials with proto and

Same was implemented in product design.

Successfully completed Pre PA, PA & BIS Testing as per standard IS/IEC 60898-1:2015

Part of Auxiliary devices design improvement team.

Achievements:-

Eliminate false latching problem of AUX-TAC from production line.

Eliminate all responsible causes for De-latching in OV, UV & Shunt & Improve

Product reliability and make customer complaint zero from a very large number.

Identify causes for OV higher voltage tripping and implement checklist.

SOFTWARE SKILLS

Creo & Auto CAD.

SAP

Minitab

Programming of 8051 Microcontroller using Embedded C language.

MS Office.

CorelDraw

PERSONAL STRENGTH

Ability to work in team with high level of involvement.

Ability to organize work to get things done with flexible approach.

Clear goal and self-motivated.

EDUCATION

Electrical Engineering, Bachelor of Engineering July-2011 to May-2015

Gujarat Technological University, India

First Class with Distinction (CGPA: 7.96/10)

Contact this candidate