REZE G. ARROYO JR.

Electrical & Instrument Engineer - Supervisor

Country of Residence or Permanent : 3-283 St.82 Blk.856 Tampines Singapore 520856

Singapore Residence Status: Dependent Pass until 2022

Availability : Immediate

Mobile Number: +658******* Singapore / +639**-*******

ac8rkx@r.postjobfree.com

Summary:

Professional skills and qualifications to manage, supervise E & I Projects, carry out activities as Electrical, Instrumentation Engineer/Supervisor/Inspector.

More than 17 year experience in E & I Projects, Oil & Gas/Petrochemical/Chemical Plants, Power Plants and High Voltage DC Transmission.

Construction Management software, MS Office, Safety oriented, complete various safety training programs, IIF (Incident Injury Free)

Process Safety Management, Process Design Consideration, and Detection & Mitigation Barriers Methods,

Hazard Identification & Risk Analysis Techniques By: Dr. Fabienne Salimi http://www.adepp.com .

Registered Electrical Engineer, Philippine Regulation Commission 2002.

Life time member Institute of Integrated Electrical Engineers of the Philippines

Completed Leadership & Supervisor Training Programme conducted by Institute of Leadership & Management through Qatar International Safety centre.

Over Seventeen years of experience in the field of Electrical Engineering, Field assigned in Onshore, Petro Chemical, Gas Plant, Industrial and Commercial, Project, Experience in Project Management Team,Installation, Testing, Commissioning, Start-up, Operation Maintenance, QA / QC / QS, Supervision, Engineering, Inspection, Documentation,. Experience and capable to handle and supervised more than two-hundred-man power, Also familiar in ISO-9001, computer literate and well trained and concerned to HSE implementation program.

WORK EXPRIENCE:

E&I Construction Supervisor

OILSERV - Erbil Kurdistan Iraq @IRAQ

Project: CRESCENT PETROLEUM/ DANA GAS – Khor Mor LPG Recovery Plant Construction (EPF)

June 2018 – December 2018 (Project Completed)

RESPONSABILITIES:

liaise with the Client’s Engineering, Operations and Maintenance staff and Installation contractor as required to ensure a consistent approach to project completion.

To provide technical support to site in terms of material inspection, retrofitting, conditioning assessment of electrical equipment, like MV/LV Motors, Transformers, Switchgears, MCC, AC/DC UPS; witness Site Acceptance & Factory Acceptance Testing.

To liaise and coordinate with other engineering disciplines for right interfacing and installation of electrical equipment

And Instrument.

Coordinate with Design team on site survey for E&I Upgrading and tie in or interface with existing plant.

Supervise Sub Contractor Daily E&I Construction Activity & Review Sub Contractor Method Statement & ITP.

Coordinate with Client on Construction Schedule, Inspection and Commissioning Procedure.

Review IFC Drawings as per Site Condition, Material Approval Requirements or Delivery & Safety Requirements.

Signed Daily Work Permit, Supervise Contractor Manpower delegation & Issue or Review Site Work Instruction.

Coordinate with Design Team on Engineering Changes at Site and Approved as Built Drawing as per site install.

Update Daily Work Schedule, attend client meeting, inspect all Sub-contractor activities as per Project Specification

&Project Quality Plan, Coordinate with client also in Mechanical Completion, Testing &Commissioning and PSSR,start up

E&I Testing & Commissioning Engineer - QA/QC

QDVC-GS E&C –ADE JV (EPC) @DOHA QATAR

Feb 2018 – May 2018

Project: Doha Metro Red Line South Project

RESPONSABILITIES:

Review all Commissioning Procedure submitted by the Subcontractor and coordinate with the client.

Attend Daily Site Inspection and coordinate with Client. (Underground Tunnel).

Review ITP Submitted by the Sub Contractor, do Site inspection, surveillance, Report NCR.

Testing and Commissioning of electrical equipment (33KV Cable, Transformer, Switchgears, MCC, UPS, Battery Interlock, loop check, function test, F&G system, BACS Cabinet I/O Signals, PLC, Fire Alarm& ELV SYSTEM)

Coordinate with Subcontractor on schedule and Progress output.

E&I Engineer – Construction Project Management Organization /PMO

QSTEC -Qatar Solar Technologies / Qatar foundation @RAS LAFFAN QATAR (Operator)

November 2016 – October 2017

Project: Construction of Poly Silicon Plant at Ras Laffan Qatar

RESPONSABILITIES:

Project Management for the Construction, Commissioning and Start Up of the Plant, until final hand over to operation. Coordinate EPC contractor on timely schedule. Review Work Method Statement, ITP, Commissioning Procedure, Mechanical Completion Package, Pre start up safety Review (PSSR) Punch listing and walk down.

Construction & Commissioning and establishment of 220/33-10 KV QATAR SOLAR ETCHNOLOGIES SUBSTATION with KAHRAMAA Contract No: GTC/465/2013. Main contractor is ALSTOM. Site name is : 220/33-10kv QSTEC (E1000) S/S of 220KV KHARAMAA Substation, 33KV Plant Substation Witness with Kahramaa personnel and Qstec for testing and commissioning of the E100 220/33-10KV S/S).11KV Motors and switchgear. Develop LOTO procedure, testing & Commissioning Procedure. Testing of transformer, relay, switchgear GIS, SCADA, Ups and battery, interlock and coordination relay study. .

Supervise the installation and commissioning of the Power Management system (PMS) -SCADA for the whole plant &System loss study and implementation of transmission line to reduce system loss in the transmission line. And segregation of system loss in power line.

Design Reviews FEED of Submitted drawings from EPC Contractor design, fabrication, brownfield construction, hook-up and commissioning of HV and LV electrical equipment.

Do review and approved material submission of EPC contractor and attend SAT test or Inspection.

Review daily work & commissioning work permit. Monitor work schedule and progress with the EPC contractor.

Testing of all motor operated valves to confirm and verify that they are working and function according to their assigned configuration value. Final checking (loop check) and verification of pressure / temperature/level transmitters to ensure that they are calibrated and properly set in accordance with their pre- determined set value. Marking and verification of location for new instruments as per general arrangement lay-out. Perform Field Acceptance Test for all existing field instruments by contractors.

Loop checking and perform insulation testing for control and power cables of air compressors.• Assigned to monitor and verify the proper location of Integrated Control and Safety System (ICSS) cables for DCS operation. Loop checking of incoming electrical cables for feeder and synchronization panel for diesel engine generators. Monitoring and loop checking of control cables for turbine engine. Preparation of Instruments Loop Folder for turn-over group. Commissioning and Start-up of process instruments such as Pressure transmitters, Temperature transmitters, Flow and Level transmitters in accordance with Commissioning and Start-up procedures.

Perform Cause and Effect testing of various electro-mechanical equipment’s. Calibration of Field instruments such as pressure and temperature transmitters, pressure and temperature gauges, pressure transducers, level gauges etc. to verify its conformity with the International Standards. Leak testing of Impulse line for various pressure transmitters, level transmitters and flow transmitters. Carry-out loop testing and commissioning of MCC electrical signals from and to MCC to DCS Marshalling cabinets and LV switchgears. Daily monitoring and inspection of various instruments in conformance with P&ID. Carry out pre-walk down of various Sub-system Work Package in every assigned Modules. Commissioning of shutdown valves (SDV’s) and blow down valves (BDV’s) in preparation for final Cause and Effect testing. Flame detectors Smoke and heat detectors, manual call points, IR gas detectors, and H2S gas detectors. Inspection of relevant instruments during Mechanical Completion (MC’s) walk down.

ELECTRICAL CONSTRUCTION SUPERVISOR/ COMMISSIONING ENGINEER

Mitsui Engineering & Shipbuilding Asia Pte Ltd. (MESA) –EPC @SINGAPORE

February 2016 – October 2016

Project : Exxon Mobil Singapore Butyl Adhesion SBA (Aurora/EOS) Project, Jurong Island Singapore

RESPONSABILITIES:

Supervise testing and Commissioning of the substation equipment. Ensure that all activities comply with the approved testing procedure.

Coordinate with ExxonMobil personnel in the testing execution. Assure HSE safety, LOTO and switching procedure is followed as per GP Standard.

Supervise the subcontractor in construction scheduling, coordination of the testing. Approved daily work permit, attend daily inspection notification, review test package, attend client walk down and punch closing.

Monitor daily progress and report to Engineering Manager. Testing of Transformer 33KV, 11KV and, 11KV VFD motor, 6.3 KV switchgear & Motor starter. (Ratio test, vector group, Hi-pot, CT polarity & Ratio test, Primary and secondary injection for CT and relay test, function test of motor starter and switchgear, megger, contact resistance test, Pre start up safety Review (PSSR), Hi Pot, inter trip, ATS function test, synchronization test, CT knee point).Authorized switching and Log out tag out person.

Serve as deputy Electrical Commissioning Manager in absent of the commissioning manager.

E &I Construction Engineer (PMC - PMT)

TaqTaq Operating Company -TTOPCO Addax Petroleum & Genel Energy Ltd JV. (Operator) KURDISTAN IRAQ

February 2013 – Feb 2016

Project: Construction of New Taq Taq Central Processing Facilities (CPF) Second Phase -IRAQ

RESPONSABILITIES:

Project Management or field supervision for the Construction of the new Central Processing Facilities (CPF). Monitor EPC work progress as per Schedule, Project Quality Plan and Safety Requirements.

Do design review FEED deliverables from EPC Company, design, fabrication, brownfield construction, hook-up and commissioning of HV and LV electrical equipment.

Do review and approved material submission of EPC contractor and attend SAT test or Inspection.

Attend Regular Progress meeting and assets site situation with respect to schedule. Review and attend site hold point inspection and surveillance work as per project specification requirements. Review and approved EPC inspection test Plan, Risk assessment and method statement, testing and commissioning procedure &turn over package as per turn over system boundary.

Design review and approval. Accept hand over package from EPC Contractor and with respect to Site walk down for punch listing prior to Mechanical Completion, Testing and Commissioning and Start up.

Involve in exploration and production, drilling, maintenance & operation, construction, PMC project management construction & Pre Start up Safety Review (PSSR).

Support production and maintenance team in trouble shooting, repair, Installation, upgrading, modification of substation equipment mcc, transformer, ups, battery charger, pumps, lighting, socket, battery, generator annunciator, cctv, communications .PMC & Review drawings for the upgrading of the existing Plant.

(Management of Change )-MOC,-Project Management Engineer for the Construction of new Central Processing Facilities .Involve in Construction, Progress Monitoring, Attend Site inspection, Resolve Engineering Query with the main contractor. Design review of drawings as per IEC, IEEE, NEMA, Company Standard and Project Specification.

Review EPC contractor method statement, Inspection test plan, Testing and commissioning procedure and handover packages. Operation Maintenance and Upgrading Engineering review and sign daily work permit of the Contractor. Review material submittal for the project, issued punch list during walk down handover.

Surveillance, Inspection and witness electrical construction works (SUBSATION 33KV transformer & switchgear erection, MCC, UPS battery chargers, battery banks, interposing relay panels (electrical/instrument interface panel), package panels, annunciator panel and VFD installation, cabling glanding & termination of control, intertrip and interlock cables) Supervise testing/commissioning transformer, switchgear, MCC, UPS, battery chargers, fire alarm & detection system, HVAC system, annunciator & interposing relay panels

Work with instrumentation group in testing Electrical Instrument interface panel simulate sending and receiving analogue and digital signal to DCS,SIS and Fire and Gas (i.e. breaker status, motor status, speed indication/reference, current indication/reference)Routine maintenance check of Transformer, MCC, Switchgear, Motors and Low voltage panels,ups, cathodic & Generators. Perform trouble shooting and replacement of electrical equipment as per daily production request. Coordinate with safety in preparing the daily permit with respect to production.

Construction of the new building facilities of TTOPCO, include in the scope is DESIGN REVIEW, DESIGN APPROVAL, MATERIAL APPROVAL and in construction stage is : Building Management System, CCTV, Telecommunication, ELV system, HVAC, fire alarm, security gate and room control, gate control, lighting facilities, security alarm, facilities, SCADA.

Do hazop, risk assessment and Hazid in any replacement and repair of electrical equipment in the facilities. Supervise 2 supervisors, 4 electricians in the daily routine work. Maintain logbook for maintenance records. Scope of work is from Rig to Central processing facilities and tanker loading station. Prepare maintenance request material for repair and spare as per job requirements. Do routine maintenance check and root cause analysis of the existing plant Calibration of transmitter (LT, PT, FT, and TT). Loop check.

Testing of all motor operated valves to confirm and verify that they are working and functions according to their assigned configuration value. Final checking (loop check) and verification of pressure / temperature/level transmitters to ensure that they are calibrated and properly set in accordance with their pre- determined set value. Marking and verification of location for new instruments as per general arrangement lay-out. • Perform Field Acceptance Test for all existing field instruments by contractors. Loop checking and perform insulation testing for control and power cables of air compressors. • Assigned to monitor and verify the proper location of Integrated Control and Safety System (ICSS) cables for DCS operation. Loop checking of incoming electrical cables for feeder and synchronization panel for diesel engine generators.

Monitoring and loop checking of control cables for turbine engine. Preparation of Instruments Loop Folder for turn-over group. Commissioning and Start-up of process instruments such as Pressure transmitters, Temperature transmitters, Flow and Level transmitters in accordance with Commissioning and Start-up procedures.

Perform Cause and Effect testing of various electro-mechanical equipment’s. Calibration of Field instruments such as pressure and temperature transmitters, pressure and temperature gauges, pressure transducers, level gauges etc. to verify its conformity with the International Standards. Leak testing of Impulse line for various pressure transmitters, level transmitters and flow transmitters.

Carry-out loop testing and commissioning of MCC electrical signals from and to MCC to DCS Marshalling cabinets and LV switchgears. Daily monitoring and inspection of various instruments in conformance with P&ID. Carry out pre-walk down of various Sub-system Work Package in every assigned Modules. Commissioning of shutdown valves (SDV’s) and blow down valves (BDV’s) in preparation for final Cause and Effect testing. Flame detectors Smoke and heat detectors, manual call points, IR gas detectors, and H2S gas detectors.

Electrical & Instrument Site Construction Supervisor

Chiyoda Singapore Pte. Ltd. –EPC @SINGAPORE

October 2012 – February 2013

PROJECT : ExxonMobil - Infineum Singa Project

Main Contractor : Chiyoda Singapore Pte. Ltd.

Industry : Oil/Gas/Petroleum

RESPONSABILITIES:

Oversee and monitor electrical subcontractor and vendor progress during construction and coordinate with other trades and discipline on the execution of electrical work.

Review subcontractor Method Statement/Risk Assessment, ITP and test packages and ensure implementation on site especially on safety & quality. Sign daily work permit and ensure safety work standard is followed. Clarify and resolve issues with regards to execution of electrical work & ensure all activities are executed safely and all risk are reduced to acceptable level.

Attend meeting with client and resolve issue arising during execution of work especially adjacent to live & operating area.

Installation and testing of heat tracing cables, junction box installation, cable termination, electrical distribution panels and transformer, as per approved drawings installation and vendor recommendations manual. Facilitate handover from piping to electrical and electrical to piping.

Discuss with engineering and sub contract administrator on required and /or additional works which are not part of the scope of works and initiate issuance of site instruction to subcontractor.

Attend to subcontractor Request for Inspection (hold & witness points as per approved ITP), monitor quality of installation and raised quality observation report and/or NCR as construction works progress and prepare inspection request to client as required.

Supervise electrical installation works of 6 electrical substation (transformer & switchgear erection, MCC, UPS battery chargers, battery banks, interposing relay panels (electrical/instrument interface panel), package panels, annunciator panel and VFD installation, cabling glanding & termination of control, intertrip and interlock cables).Supervise testing/commissioning transformer, switchgear, MCC, UPS, battery chargers, fire alarm & detection system, HVAC system, annunciator & interposing relay panels (hi-pot, PI & SI injection, contact resistance, insulation resistance, winding resistance, ratio and vector group confirmation, oil dielectric strength test, excitation current test, transformer alarm/trip simulation, loop/continuity check, circuit breaker mechanical and functional test, motor starter module functional test, motor solo run, fire alarm/detection functional test, HVAC purging and leak test on refrigerant pipe).

Work with instrumentation group in testing Electrical Instrument interface panel simulate sending and receiving analogue and digital signal to DCS (i.e breaker status, motor status, speed indication/reference, current indication/reference. Review and approve subcontractor daily work permit, manage electrical LOTO system International industry codes and standards related to intrinsically safe system and electric system for instrumentation.

Testing of all motor operated valves to confirm and verify that they are working and functions according to their assigned configuration value. Final checking (loop check) and verification of pressure / temperature/level transmitters to ensure that they are calibrated and properly set in accordance with their pre- determined set value. Marking and verification of location for new instruments as per general arrangement lay-out. • Perform Field Acceptance Test for all existing field instruments by contractors.

Loop checking and perform insulation testing for control and power cables of air compressors. Assigned to monitor and verify the proper location of Integrated Control and Safety System (ICSS) cables for DCS operation. Loop checking of incoming electrical cables for feeder and synchronization panel for diesel engine generators. Monitoring and loop checking of control cables for turbine engine. Preparation of Instruments Loop Folder for turn-over group.

Commissioning and Start-up of process instruments such as Pressure transmitters, Temperature transmitters, Flow and Level transmitters in accordance with Commissioning and Start-up procedures. Perform Cause and Effect testing of various electro-mechanical equipment’s. Calibration of Field instruments such as pressure and temperature transmitters, pressure and temperature gauges, pressure transducers, level gauges etc. to verify its conformity with the International Standards.

Leak testing of Impulse line for various pressure transmitters, level transmitters and flow transmitters. Carry-out loop testing and commissioning of MCC electrical signals from and to MCC to DCS Marshalling cabinets and LV switchgears. Daily monitoring and inspection of various instruments in conformance with P&ID. Carry out pre-walk down of various Sub-system Work Package in every assigned Modules. Commissioning of shutdown valves (SDV’s) and blow down valves (BDV’s) in preparation for final Cause and Effect testing. Flame detectors Smoke and heat detectors, manual call points, IR gas detectors, and H2S gas detectors. Inspection of relevant instruments during Mechanical Completion (MC’s) walk down.

Site Senior Electrical Engineer Construction - PMT /Consultant /Owner Engineer

Parson and Brinkerhoff Ptd. Ltd. – Consultancy @ SINGAPORE

May 2012 – October 2012

Project : GMR Energy Power Generation Plant CCPP (Combine Cycle Power Plant) 2x 400 MW

Main Con. : Siemens Pte. Ltd & Samsung C&T Corporation

Industry : Power /Energy

RESPONSABILITIES:

Owner Engineers or Representative/ Consultant, Project Management, -Review Engineering Design, Drawing and Commissioning procedure as per NEMA, IEC & project Specification, -Act as owner side consultant in the implementation of project construction and Commissioning, -Monitor all main contractor in the Construction, Installation and commissioning of the project Power Plant,-Attend Site inspection and witness commissioning. Review invoice submitted by subcontractor and main contractor versus the main contractor submitted progress report.

Issue Non-Conformance Report to the contractor, -Update site construction progress as per schedule. Resolve engineering issue at site, Review Design Query, Inspection test plan, Method statement. Plant capacity: (230 kv GIS, 2 pcs. 500 MVA transformer, Generator 2x400MW), Attend contractor’s meetings with regards: Progress, Quality and Safety.

Do review and approved material submission of EPC contractor and attend SAT test or Inspection.

Design review FEED and approval of deliverables drawings from EPC Design, fabrication, brownfield construction, hook-up and commissioning of HV and LV electrical equipment

Witness FAT and SAT inspection, Approved and issue handover certificate as per project completion. Coordinate with local authorities during tie in. Assets 230 KV SUBSTATION construction and commissioning.

Responsible in conducting technical reviews, comment and approve Engineering deliverables and change/work variation orders, assist and advise engineering leaders about E&I issues/expectations during technical discussions with EPC/Sub Con-supplier, Interface with others engineering/construction discipline to ensure efficient and work execution.

Qualify EPC/sub-suppliers requests for deviation RFD, MOC (management of change) and TQ/RFI technical query according to the company best practices, Participate in (Site acceptance Test) SAT, MC system walk-downs, (PL activities) and identify Commissioning Start Up related issues that might impact commissioning programs and other project activities.

Electrical & Instrument Site Engineer

Black Cat Engineering and Construction – EPIC @QATAR

Jan 2012 – April 2012

Project : Upgrade of Recycle Compressor at ARAB D Plant, QATAR PETROLEOUM

Main Contractor : Black Cat Engineering

Industry : Oil/Gas/Petroleum/Petrochemical

RESPONSABILITIES:

Scope of work is Engineering Procurement Installation Commissioning. Review all Engineering Design in compliance to Clients Requirements and International Standard (IEC, NEMA, IEEE).- Review all Procurement is in Accordance with the approve requirements within Project Specification and clients requirements.

Provide material take off as per project requirements. -Review and Approved all as built drawings, -Submit Mechanical Completion package, -Supervise all Sub contractor and vendors during Construction, Installation and Commissioning stage of the project, monitor project progress and review all site engineering query with regards to some design and construction issue.

Attend regular meeting with client on project management issue. Qatar Petroleum Permit to work Authorized applicant. (Brown field), familiar with shut down procedure, prepare method statement and risk assessment.

Ensure work is executed safely and within HSE standard of the project (ensure proper controls in place and risk is mitigated to as low as reasonably practicable) champion the culture of caring. Anticipate, coordinate, expedite, resolved any issue that may arise/arises during execution of E & I works.

Verify and approve field routed installation, ensure installation are sighted, positioned/oriented properly to avoid being an obstruction to operation and maintenance personnel and ensure all is reflected in the as built drawing.

Attend weekly construction meeting, highlight any issue/constraints with regards to safety, quality & schedule. Attend multi discipline system walk down with client, generate and classified punch during walk down.

Supervise Installation/Inspection/Testing of Fire Alarm/Detection System (VESDA & Linear Heat Detection System & Addressable Smoke/Fire Detection System), Access Control System, PA system & CCTV.

Verify punch item is rectified and close, review and expedite/completeness of test packs for Fire & Gas System, Access Control System, PA & Intercom System, Power, Lighting & Small power and Instrumentation Test Packages. Supervise electrical construction works (transformer & switchgear erection, MCC, UPS battery chargers, battery banks, interposing relay panels (electrical/instrument interface panel), package panels, annunciator panel and VFD installation, cabling glanding & termination of control, inter trip and interlock cables).Supervise testing/commissioning transformer, switchgear, MCC, UPS, battery chargers, fire alarm & detection system, HVAC system, annunciator & interposing relay panels (hi-pot, PI & SI injection, contact resistance, insulation resistance, winding resistance, ratio and vector group confirmation, oil dielectric strength test, excitation current test, transformer alarm/trip simulation, loop/continuity check, circuit breaker mechanical and functional test, motor starter module.

Testing of all motor operated valves to confirm and verify that they are working and functions according to their assigned configuration value. Final checking (loop check) and verification of pressure / temperature/level transmitters to ensure that they are calibrated and properly set in accordance with their pre- determined set value. Marking and verification of location for new instruments as per general arrangement lay-out.• Perform Field Acceptance Test for all existing field instruments by contractors. Loop checking and perform insulation testing for control and power cables of air compressors.• Assigned to monitor and verify the proper location of Integrated Control and Safety System (ICSS) cables for DCS operation. Loop checking of incoming electrical cables for feeder and synchronization panel for diesel engine generators. Monitoring and loop checking of control cables for turbine engine. Preparation of Instruments Loop Folder for turn-over group.

Commissioning and Start-up of process instruments such as Pressure transmitters, Temperature transmitters, Flow and Level transmitters in accordance with Commissioning and Start-up procedures. Perform Cause and Effect testing of various electro-mechanical equipment’s. Calibration of Field instruments such as pressure and temperature transmitters, pressure and temperature gauges, pressure transducers, level gauges etc. to verify its conformity with the International Standards. Leak testing of Impulse line for various pressure transmitters, level transmitters and flow transmitters. Carry-out loop testing and commissioning of MCC electrical signals from and to MCC to DCS Marshalling cabinets and LV switchgears. Daily monitoring and inspection of various instruments in conformance with P&ID. Carry out pre-walk down of various Sub-system Work Package in every assigned Modules. Commissioning of shutdown valves (SDV’s) and blow down valves (BDV’s) in preparation for final Cause and Effect testing. Flame detectors Smoke and heat detectors, manual call points, IR gas detectors, and H2S gas detectors. Inspection of relevant instruments during Mechanical Completion (MC’s) walk down.

E&I Site Engineer (Construction)

Rotary Electrical Company Pte. Ltd.@SINGAPORE

March 2010 - January 2012

Project : Exxon Mobil Chemical, Singapore Parallel Train (Olefin Recovery Project) -SINGAPORE

Main Contractor : SHAW Stone and Webster

Industry : Oil / Gas / Petroleum/Chemical

RESPONSABILITIES’:

Responsible for managing the cost, schedule control and technical coordination with the client and project team & Monitor Schedule

Responsible for the technical review of drawings, materials, equipment, procedures and other pertinent project documents.

Responsible for interpreting and clarifying all technical details to the project team. Provide technical direction or instruction to personnel involved, proposing and reviewing of corrective actions. Coordinate with other departments for problems relating to design and activity execution. Coordination meeting with other sub-contractor and review payment as per progress submitted.

Conduct daily toolbox meeting together with the Construction and Quality Personnel. Ensure that all aspects of works

Contact this candidate