THOMAS M. WNUK

N**W***** Hastings Ct. Sussex, WI 53089 Home: 262-***-**** Cell phone: 262-***-****

I have been retired, but I am now going to reenter the workforce.

SUMMARY OF QUALIFICATIONS:

Over 30 years of Electronic Technician experience

4 years of electronic assembler experience

Proficient in use of various electronic troubleshooting equipment, including signal generator, oscilloscope, frequency counter, and digital multi-meter.

EXPERIENCE:

Keystone Staffing 02/2015 -- 06/2015

Circuit board tester, Contracted at Milwaukee Electronics, Temp Job

Attach circuit boards to test fixture and run tests to make sure the board is not defective.

MindLance Corp. 07/2014 – 10/2014

Circuit board tester, Contracted at Eaton Corp. Watertown,WI, Temp Job

Attach circuit boards to test fixture and run tests to make sure the board is not defective.

Lepel Corp., Waukesha WI 07/2011 – 01/2014

Electronics Technician (Reason for Leaving: company hired an engineer - technician.)

Troubleshoot and repaired induction heating equipment. These machines are cap sealers that would heat foil lids.

Involved using oscilloscope, multi-meter, clamp on ammeter to troubleshoot equipment and performed soldering.

Went on field service calls as needed.

Reinder’s Inc., Elm Grove WI 08/2010 – 02/2011

Assembler, Part Time

Worked on at-home project which includes soldering 55-foot rain switch cables to 15-pin D-connector for use with TORO irrigation systems.

Spliced cables together and cover with heat shrink tubing.

The Associates Group, New Berlin WI 10/2008 – 06/2009

Assembler, Contracted at American Superconductor, Temp Job

Worked at a Manufacturer of wind power systems.

Assembled power inverters.

Programmed circuit boards using Windows based computer to download code to PROM chips.

Restocked assembly stations with new inventory of parts for the next assembly phase.

Eagle Technology Group 05/2006 – 09/2007

Electronics Technician, Assembler, Contracted at Criticare Systems, Temp Job

Performed assembly, testing and troubleshooting of medical monitoring equipment.

Medical equipment checked ECG, SPO2, temperature and blood pressure.

Tested to make sure the equipment was within spec.

Downloaded information from a PC running Windows XP.

Disassembled the system, replaced the bad module and reassembled the system, if an error occurred.

Documented all testing.

Company is ISO 9001 certified.

Reinder’s Inc., Elm Grove WI 06/1997 – 11/2003, 05/2004 – 03/2006

Irrigation Controller Technician

Troubleshoot and repaired golf course irrigation systems-both electronic and mechanical controllers.

Electronic controllers are microprocessor based with triacs or relays to turn on sprinkler heads at 24vac. Most systems also have a central unit connected to a PC that communicates with the controllers on the golf course.

Repaired customer computers when they have been disabled by power surge.

Provided service support with customers on the telephone.

Went on field service calls when needed.

Medical College Of Wisconsin, Milwaukee WI 11/2003 – 05/2004

Electronic Systems Technician

Soldered accelerometer cables to Lemo plugs.

Checked and repaired tape switches after vehicle crash tests.

Set cables up to high speed video cameras for vehicle crash tests.

Put together parts orders for electronic components.

Checked accelerometers on data acquisition system.

West Side Radio, Milwaukee WI 1975 - 1997

Electronics Technician

Performed troubleshooting and repair of microprocessor-based consumer electronic items

Utilized various test equipment, including signal generator, oscilloscope, frequency counter, and DMM (digital multi-meter).

EDUCATION:

Waukesha County Technical College - Associates Degree in Electronics Technology (06/1991)

Earned A+ certification on computer hardware and operating systems

Contact this candidate