Engineer Project
Resume:
Education
**** - **** *****, ************ ****
Manipal Institute of Technology, Manipal
CGPA: 9.03
Specialization: Industrial automation and Robotics 2012 - 2016 BE., Electronics and Instrumentation
Sri Jayachamarajendra College of Engineering, Mysore CGPA: 8.21
Specialization: Instrumentation technology
2010 - 2012 PUC
Alva’s PU college, Moodbidri
Percentage: 82.6
Specialization: PCMB
2009 - 2010 SSLC
Sri Ramakrishna Vidyalaya, Hosanagara
Percentage: 85.28
Experience
April 2018 -
Oct 2018 System Engineer National Instruments
Design and development of control loops for aircraft high lift system
• Design and development of different control loops for Power drive unit of high lift system using Simulink tool kit.
• Responsible for understanding the customer requirements and generating the requirement document for development of control loops.
• Integrating the models developed in Simulink with NI veristand in real time and validating the models.
• Validated the models by deploying into NI PXIe system using PXIe- Embeded controller and Various PXI/PXIe cards.
• Responsible for Preparing Design, verification and validation docu- ment of different control loops.
• Been a part of application debugging and upgrading the application as and when requirements changes.
• Responsible for executing verification and validation of models in- tegrated with NI Versistand for different control loops.
• Responsible for tuning the controller models to match the test cases.
June 2017 -
March 2018 System Test Engineer MOOG India Technology Centre Design & development of Simulink model of TEGRA (trailing edge gear rotary actuator) endurance rig for test system simulator.
• Development of Mathematical model of TEGRA (trailing edge gear rotary actuator) endurance rig & Validate the model.
• Responsible for understanding the system requirements and gen- erating the requirement document for simulink model development.
• Modelling the drive unit of TEGRA (Trailing edge gear rotary actua- tor) endurance rig using sliding mode control technique.
• Preparing and executing test cases for different control loops.
• Integrating the models developed in Simulink with NI veristand and validating the models.
• Preparing Design, verification and validation document of En- durance test rig.
• Implementing of different controller designs like PID and Sliding mode controllers and tuning those controllers to match the test cases.
Anikethana M R
System Engineer
/in/b7174393
***.****@*****.***
Skills
Automation
and robotics
MATLAB
Simulink
C
& C++
NI Teststand
NI Veristand ROS
& PLC
LabVIEW
General Softwares
MS Word
PowerPoint
SQL
MS Visio
Projects
Automatic Battery bank changer
• Responsible for understanding the Project requirements.
• The project aim here is to design a PLC based 24VDC power sup- ply that will ensure spike less uninterrupted power with the use of battery banks.
• The system will operate in either automatic or manual mode. Man- ual control buttons are de-activated during automatic operation.
• The PLC system monitors bus bar voltage when the power supply is running.Incase the bus bar voltage drops below certain point the other battery will take over to prevent bus bar volatge from drop- ping further.
• Responsible for preparing the thesis report for academics.
• Tools : Rexorth Bosch PLC, relays, LED,Potentiometer. Smart home using LabVIEW
• Responsible for understanding the Project requirements.
• It was a sensor based efficient home security system. The Idea was to design a system that detected intrusion and alerted the owner and also helps in reducing power consumption.
• The system can monitor the temperature, lighting, burglar alarm, and camera of the house these parameters are connected to Lab- VIEW software as the main controller for these systems.
• All the sensors is connected directly with NI DAQ’s(Data Acquisition system).LabVIEW reads the signas from sensors as variable analog values. After processing the signal, the LabVIEW will send a signal for actuation of components(Light,Fan,Alarm,Camera).
• Responsible for preparing the project report for academics.
• Tools: LabVIEW, NI DAQs, Sensors and camera
Solar based advanced water quality monitoring system using wireless sensor network
• Responsible for understanding the Project requirements.
• This project involves in design a Solar powered system that can sense the pH, temperature and salinity of the liquids and to monitor the same through wireless firmware device.
• All sensors and Zigbee modules are connected to the controller board and collect data from various sensor nodes and send it to base station by wireless channel.
• simulate and analyze various parameters for quality control and publish the corresponding record over web for public information and further assessment of water resource.
• Responsible for preparing the thesis report for academics.
• Tools: Solar pannel, Arduino, Zigbee module
Internship Training
• Summer internship program at center for system design, NITK Surathkal based on the Study on sensors & data acquisition system using graphical program- ming environment’.
• Responsible for preparing the internship report for academics. Extra-Curricular Activities
• Worked as an EVENT MANAGER in IEEE SJCE 2014-15.
• worked as STUDENT COORDINATOR in IEEE SJCE for the year 2013-14.
• Successfully organized technical fest CYBERIA 14 & 15 under the banner of IEEE SJCE.
• Successfully organized technical fest TUXEDO 14 & 15 under the banner of IEEE SJCE.
Technical Exposure
• Attended the LabVIEW workshop conducted by National Instruments.
• Attended the MATLAB workshop conducted by MathWorks. References
• Mr.Karthik SP, Snr Systems engineer, NI,India; *******.**@**.***
• Mrs.Sherine Jesna V A, Assistant prof.,MIT Manipal, India; *******.*****@*******.***
• Mr. Mukesh Prasad, Sr.Team lead, Moog Inc., India; ******.******@*****.***
Contact this candidate