Mechanical Technician
Resume:
JAYSON A. GAMIL
Mechanical Fitter/Technician
Sampaga West, Batangas city 4200 Philippines contact # +63-906-***-****
e-mail address: ***********@*****.*** +63-936-***-****
FCF GOLD MOLYBDENUM PROJECT
Runruno, Quezon Nueva Vizcaya Philippines
Fixed Plant Mechanical Maintenance Fitter
September 6, 2017 – Present
To conduct Plant wide inspection for possible maintenance and/or repair.
Perform maintenance of Semi- Autogenous Grinder (SAG MILL) to enhance reliability and optimum performance
Monitoring/securing good operating condition of Bacterial Oxidation (BIOX)
Do the necessary maintenance and accurate diagnosis for possible cause in failure of the equipment.
To perform condition monitoring and history report to avoid recurrence of equipment failure.
Perform day and night duty depends on task necessity.
Overhauling/troubleshooting of various pumps and valves.
To attend everyday tool box meeting to much wider discuss about plant condition and to do necessary action for production, safety awareness and environmental issue if there is any.
Japan Gas Corporation (JGC Phil)
Maintenance Division
Barangay Rio Ruba, Bataraza Palawan Philippines
April 2017 – June 2017 – Mechanical Technician
(Shutdown Activities only)
Assemble /Disassemble and Installation of equipment such as motor, pump, compressors etc.
Maintenance Servicing of Autoclave Agitator.
Installation of Agitator Gearbox and Mechanical Seal
Alignment of High speed and Low speed coupling
Opening and Box-up of Flash tanks.
Maintenance Servicing of LEWA- pump (acid unloading pump) replacement of Radial seal, Combination Valve and Change oil as well.
Maintenance Servicing of Pump head.
Overhauling of centrifugal pump including pump assembly
Executing all task ahead of schedule without sacrificing safety and environment to enhance its reliability and optimum production.
First Quantum Minerals (FQML)
Coal Fired Power Project
Donoso Colon Cobre PANAMA
Mechanical Fitter
(March 06, 2016 up to December 14,2016)
To align motor and pumps – Pumps to gearbox using dial indicator method
Assembling of Re-claimer
Securing proper tension and alignment of conveyor belt
Assembling and tightening of rails for Re-claimer
Installation of Rollers and Conveyor Belts
To establish correct bolt projection as per drawing
To install tank for feed water and pumps
To layout the center line, position and elevation of tanks including grouting of foundation.
Setting up of packer plates using dumpy level prior to grouting as per drawing
Understanding drawing both civil and mechanical
Assist to vendor for installation of turbine and compressor
Installation of boogie and bearings for the Re-claimer
Establish the correct elevation in all equipment using appropriate leveling instrument
Follow and understand safety rules and regulation and providing additional safety information and guidelines.
Offering some additional safety measures according to previous experience
Serves as a leader in the team in which I belong due to my wide knowledge and technique.
Mafumeira Sul Project
Block-0 Malongo Cabinda Angola
Daewoo Shipbuilders and Marine Engineering (DSME)
Dimension all Manpower Incorporated
Mechanical Fitter
(May 01, 2015 to November 08, 2015)
DUTIES and RESPONSIBILITIES
Serve as a team leader in the absence of my supervisor
Has an ability to communicate with client in oral or written on a very polite manner.
Combine and raise a good idea to have time efficient and avoid reworks
Suggest and execute very good work analysis
Trusted by superintendent for every task even without supervision
Because of my ability and experience, work was done in a very simple way.
Preservation of all mechanical equipment and components as required
Perform installation of rotating and static equipment including alignment and levelling
Follow safety rules and regulations religiously and share my wide experience and skills to boost safety awareness.
To finish assign task but not harming the environment.
Knowledge and skills in reading and using of precision tools
Centering/Leveling of skid using machinist level, square level etc.
Follow and understand P&ID.
Levelling and centring of skid and flanges to eliminate pipe stress.
Correcting soft foot on motor or gearbox if there is any.
Leveling, centering of anchor bolts using dumpy level & electronic level.
Alignment of pumps, motor, gearbox compressor and turbine using laser alignment method
Filling correct and exact amount of oil fit for gear boxes speed to enhance its reliability and durability, filters as well.
Perform lathe machining, milling and grinding
Using of manual torque with standard torque value for small bolts.
Torqueing of bolts using standard torque value.
Lay out and execute cutting of bars for special purposes using cutting torch.
Perform basic welding.
Installation and maintenance of temporary water facility.
Perform pipe cutting using precision cutting tools. (TRI-TOOL) cutting machine
Setting up and using of pneumatic torque wrench
Support other team so as the work will be efficient.
Attend safety seminars and training as company requirements.
Recondition and maintenance of pneumatic tools and portable blowers.
L.ARMANI TRADING & GENERAL SERVICES
727 Sitio D’Hope, Brgy. Libjo
Batangas City, Batangas 4200 Philippines
Mechanical Foreman
(May 5, 2014 – March 6, 2015)
Directly report to supervisor.
As team leader I ‘m not teaching how to do. I am showing how it’s done.
Has a flexible attitude towards the role.
Giving instruction to subordinates.
Ability to work under pressure with tight deadlines.
Taking the lead for all safety matters.
Pull out and install different types of valve.
Disassembles and assembles of columns, vessel, drums and heat exchanger
Ability to maintain attention to detail by providing high levels of accuracy
Ability to work as part of the team whilst using my own initiative to make autonomous decisions to ensure the project deadline compliance
Assemble / Dis assemble of Hydraulic Cylinder
Highly motivated, driven disciplined with a “can do” attitude.
Practice and perform health and safety procedure.
PNG / LNG Esso Highlands Limited
Hides Southern Highlands Papua New Guinea
Chicago Bridge and Iron (CB&I)
(November 15 2012 -April 13 2014 –Millwright)
Work as a team leader
Work very flexible, depends on rapid changes of work schedule
Reporting completed jobs using computer and updating ongoing task
To perform mechanical equipment installation.
Preparation of skid for rotating and static equipment.
Installation of internal trays, pig launcher etc.
Installation of compressor and turbine.
Layout Turbines and Compressors
Perform civil works to help secure the stability of equipment.
Assembling ducting, filters, fin fan coolers, turbine and compressors casing etc.
Securing equipment stability and eliminating soft foot to enhance its reliability and optimum performance.
Surveying, calculating slopes, reading civil and mechanical drawings
Sighting elevations for manhole, catch basin and any other civil related activities.
Centering/Leveling of skid using machinist level, square level etc.
Leveling, centering of anchor bolts using dumpy level &electronic level.
Alignment of pumps, motor, gearbox and turbine using laser alignment method.
Eliminate pipe stress using precision tools.
Setting up and using of pneumatic torque wrench.
Torqueing of bolts using standard torque value
Cutting of Pipe using precision cutting tools. (TRI-TOOL) cutting machine
Trained and certified worker in confine spaces.
Trained and certified Self Contained Air Breathing Apparatus (SCBA) user.
Trained and pass on working at height
.
Japan Gas Corporation Philippines (JGC Philippines)
Maintenance Division
Riotuba, Bataraza Palawan Philippines
(April 2007 -February 2012 - Mechanical Technician)
Mechanical lead man when Plant is on Scheduled for Major/Minor Shutdown.
Has the technical procedure to replace bearing assembly of Autoclave Agitators, also mechanical seal replacement of Titanium agitator blades and any other mechanical works within Autoclave and HPAL area.
Overhaul, repair, troubleshooting of rotating mechanical equipment oil refinery processing plant, e.g. pumps, turbines, compressors, fans and blowers.
Do the necessary and accurate diagnosis during the malfunction of equipment to make the job easier ahead of schedule but not sacrificing safety.
Disc Separator replacement, cleaning of strainer, replacement of internal parts on 2/2 way valves. Diaphragm replacement, Piston ring, piston cylinder liner replacement and other related mechanical activity on GEHO pumps.
Has the capability to perform several pump and motor alignment, and also belt driven pumps with accurate tension and adjustments.
Carry out the proper preventive maintenance on such equipment to enhance its reliability and efficiency in conjunction to optimum plant production.
Perform mechanical trouble shooting on LEWA pump (acid unloading pump)
Carry out inspection for all mechanical equipment, perform preventive maintenance and repair in storage tank suction and discharge.
Replacement of shafting blades to make sure and enhance its reliability and optimum production without any injury and harm to environment.
Has the capability and knowledge on valve replacement on GEHO PUMPS (suction and discharge cone valve).
Perform daily scheduled maintenance activity plant wide such Boiler/Utilities - Ore Preparation / High Pressure Acid Leach / Counter Current Decantation / pre Neutralization / Mix Sulphide and other related area within.
Technical Knowledge on Travagrate overhauling in boiler coal feed/fire.
Adherence to standards of proper alignment procedures in refinery practice using the conventional & reverse dial indicator method.
Initiate the proper evaluation failures and recommend the necessary mechanical repair.
Do the necessary maintenance on conveyor belts such as splicing and/or replacement
knowledge in overhauling rotating equipment such as pumps (centrifugal/reciprocating/rotary), turbines (steam/gas turbine) compressors (centrifugal/reciprocating) fans, blowers and other auxiliary equipment.
Work in the proper implementation of established maintenance procedures without sacrificing safety and environment
Follow and understand P&ID.
Lay out and execute cutting of bars for special purposes using cutting torch.
Observe the established safety practices in carrying the assigned task.
Securing proper alignment and condition of drum washer or throw mill
Maintenance servicing of scrubber
Maintenance servicing of ball mill
Perform basic welding
Jayson A. Gamil
Mechanical Foreman / Technician
PERSONAL INFORMATION
Address:
Sampaga West Batangas City
Batangas,4200 Philippines
Date of Birth:
April 05,1980
Place of Birth:
Balatero, Puerto Galera,
Oriental Mindoro
Civil Status
Married
Citizenship
Filipino
Trainings and Seminars
BOSIET Training
January 22-24 2015
BASIC Training
January 28- February 04 2015
Basic Auto cad
September 2014
Permit to Work
July 20, 2007
Awareness Modules
August 7-9, 2007
Toolbox Modules
August 8,9,16 2007
Other Trainings
Technical Education Skills and Development Authority (TESDA)
Machining NC I
Certificate # 120***********
(B.O.S.H.E.T)
Basic Offshore Safety Health and Emergency TrainingP& I D.
Piping and Instrument Diagram
PASSPORT # PO273868A
SSS # 04-3177809-5
TIN # 301-***-***-***
Pag- ibig # 121*-****-****
Philhealth # 19-051314616-0
Driving License #
DO1-07007471
EDUCATIONAL BACKGROUND:
AMA Computer College
Bachelor of Science in Computer Science
Bolbok Campus Bolbok Batangas City Batangas 4200 Philippines
TESDA Regional Training Center – CALABARZON
P. Herrera Street Batangas City 4200 Batangas Philippines
Lathe Machining ( NC-I )
University of Batangas
Hilltop Road, Kumintang Ilaya
Batangas City Batangas
Bachelor of Science in Civil Engineering
(College level)
Special Award:
Two time recognized by the client safety team for exemplary safety performance.
To perform lathe machine operation
Assess and pass course qualifier
Given a license by Technical Education and Skills Development Authority (TESDA) for lathe machine operation
Satisfactorily completed the required number or hours studying lathe machine operation
As a class president, I am responsible to perform the best and serve as an example to the group
To perform grinding operation using surface grinder
To perform drilling operation using drill press machine
References:
Domingos Coelho
Senior Mechanical Supervisor
First Quantum Minerals (FQML)
Coal Fired Power Project
Donoso Colon Cobre, Panama
Contact # +507-****-****
Email: ***.***@*****.***
Engineer Jayson Evia
Project Engineer
Dimension All Manpower Incorporated
Mafumeira Sul Project
Daewoo Shipbuilders Marine Engineering (DSME)
CHEVRON Angola Project
Contact #
Armando C. Lazarte
General Manager
L. ARMANI Trading and General Services
727 SitioD’Hope, Libjo Batangas City
Batangas 4200 Philippines
(043-***-**** /402 2593
Mobile # +63-919-*******
Engineer Eric Quintero
Mechanical Engineer
Contact #
Email: ******@***.**.**
***********@*****.***
PNG/ LNG Project
ESSO Highlands Limited
Southern Highlands Papua New Guinea
Engineer Ryan Labana
Senior Engineering Supervisor
Japan Gas Corporation Philippines (JGC Philippines)
Contact #
OTHER TRAININGS:
P.C. Operation
Microsoft Office
September 13 – 21 2016
Microsoft Excel
September 13 – 21 2016
Contact this candidate