Vishal Chopade
Ph. 646-***-**** LinkedIn: in.linkedin.com/in/vishal-chopade-4b4009a3 Email: ********@***.*** OBJECTIVE:
An Electronics Engineer seeking full-time position as Embedded-Firmware Developer/Designer/Hardware Engineer. SKILLS:
Embedded Systems Firmware Programming (Embedded C/C ARM cortex family, SoC programming, CAN, I2C, SPI, UART, USB, Ethernet, PCIe, Middleware and Application Software Design, APB and AMBA bus architecture(ARM), RTOS (FreeRtos, VxWorks).
Programming Embedded C(Certified), C++(Certified), Python. Tools Keil Vision (MD-5), Xilinx, Saleae Logic (Logic Analyzer), Lauterbach Trace-32 (JTAG Debugger), Digital Oscilloscope, Version Control Tools (Git system), OrCAD, Cadence Allegro PCB, Altium Designer, EagleCad, Dip Trace, KiCad, Multisim, Labview, CCS, Mbed and IAR embedded workbench, Digital Signal Processing. Communication Systems CDMA/FDMA/TDMA, LTE, RF Systems, Bluetooth, GSM/EDGE, Wi-Fi WLAN 802.11a/b/n, OFDM/OFDMA, SC-FDMA, Modulation Techniques (PSK, BPSK, QAM etc.) EXPERIENCE:
Adex Technologies, Sunrise, FL, USA Apr 2018- Present Software and Embedded Systems engineer
On Project With Magicleap - consumer electronics calibration and automation (robotics)
Optotrack testing and Zaber XMCB2 programming for precision automation robot. (stepper motor support)(KuKa replication).
Calibration of consumer electronic product for Better Vision and tracking of a device. Worked on sensor fusion.
Strong Matlab Programming Environment. Embedded systems design for calibration machines.
Digital Signal Processing environment for data acquisition and observation. Sensor Fusion studies for eliminating the error due to lack of sensor vision. Magicleap, Plantation, FL, USA May 2017- Aug 2017
Electrical Engineering Intern:
Designed the schematic for the wearable wireless consumer electronics device using NRF 52832. Programming for cortex m4 microcontroller were implemented using embedded C programming KEIL v5 tool.
Testing embedded systems, software and APIs. Hands on experience with sensor specific measurement equipments.
Designed the automated power circuit to reduce the switching by almost 50%. Used I2C protocol for advantage. Worked on power distribution systems.
Worked on CADENCE schematic design tool for efficient PCB design. Worked with terminal emulator applications like tera term 4.88 and Putty.
Performed testing and debugging of sensors using test instruments Oscilloscope, Logic Analyzer, Signal generator, and Spectrum analyser, JTAG.
Tested the sensors for efficiency and sensitivity. Mathematical calculation was programmed on MATLAB.
Worked on complete risk analyses, design calculations, Failure Modes Effects.
Worked on sensors like inertial, pressure, ambient light, proximity. Florida International university, Miami, FL, USA Aug 2016- Dec 2017 Software and electronics Engineer/ Research Assistant:
Development project of wireless wearable Healthcare device using multiple wireless protocol like Wi-Fi/ Bluetooth/BLE 4 and Nordics microcontrollers nrf51 series. Research and programming for 40% more power saving possibilities.
Program embedded system using C programming (C certified programmer).
Testing embedded systems, software and sensors for better efficiency and product diversity.
Implementing drivers for UART, SPI, I2C, External/Internal ADC, EEPROM, Watchdog, Clock, Interrupts, Timers and PWM.
Hands on experience with software’s like Multisim, Labview, Keil, CCS, Mbed and IAR embedded workbench.
Experience working with variety of microcontrollers like NRF51 series, TI 2650, TI MSP430.
PCB designing softwares like EagleCad, Dip Trace, KiCad.
Designed a code on Matlab for DSP kalman filter for GPS and INS of car. H2 Technologies, Pune, India Aug 2014 – June 2016
Software/Electronics Engineering Intern:
Worked as a software engineer performing every task involved in programming in embedded C.
Worked on projects involving the technologies like wireless communication, automation, robotics and low power microcontrollers.Worked with I2C, SPI, CAN for automotive project.
Worked with sensors like pressure, ambient and moisture.
Learned programming and interfacing of microcontrollers like ARM, 8051 and PIC etc.
Worked on the software’s like MATLAB, KEIL, MULTISIM, MBED, ARDUINO debugging tool.
Actively participated in developing my undergrad project to the new level using the wireless communication and low power consumption using NRF 5X series.
EDUCATION:
Masters in Electrical and computer engineering
Florida International University
Dec 2017
Embedded Software and Hardware Systems
Technoscript, Pune, India
June 2016
Bachelor of Engineering in Electronics and Tele. Engineering University of Pune, India
May 2014