Test Technician

*************@*****.*** phone #: 657-***-****

OBJECTIVE

Seeking full time employment with a company that will allow me to utilize my technical skills

ELECTRONIC SKILLS

Schematic Reading QA Inspection

Troubleshoot Soldering

AC/DC circuits Soldering and resoldering

Electronics testing PCB assembly and prototyping

EQUIPMENT KNOWLEDGE

Digital multi-meter DC System power supply Noise figure meter

Digital sampling oscilloscope Generator control unit(GCU) Magtrol analyzer

Frequency sweeper Logic analyzer Hydraulics

Network analyzer Avtron test stand

EDUCATION

Southern California Institute of Technology August 2012

Biomedical Technology

Principles and Practice in:Electronic Fundamentals

Digital Electronics

Semi-Conductors

Human Anatomy

Biomedical Instrument Operations

Medical Device TroubleshootingBiomedical Instrumentations Lab

Identify, troubleshoot and repair problems relating to the operation of electronics based biomedical instruments including: ECG measurements, blood pressure measurement systems, defibrillators and ESU performance, bedside monitoring systems, instrumentation amplifiers for ECG systems, operation of dialysis machines, ventilators and more

EMPLOYMENT HISTORY

CIRCOR AEROSPACE

Corona, CA 6/2015 - Present

MRO Technician

Maintenance repair overhaul of industrials energy medical devices and aerospace products. Receive units evaluate, repair assemble, final functional test and under FAA regulations.

*************@*****.*** phone #: 657-***-****

HONEYWELL AEROSPACE

Torrance, CA 3/2014 – 6/2015

Sr Engineering Test technician

ESD certified

Received and inspect mechanical and electrical functional test of all aerospace products

Actuators ac and dc motors control circuit card and boards for aircraft parts also bench testing Destructive test Using magtrol console Dynomometer

Alcon Laboratories

Irvine, CA 8/2013 – 2/2014

Electro Mechanical Technician

Assemble microscopic cataract machine for eye surgery. Material handling, building sub assemblies, reading prints by using winchill, some soldering, crimping cable, final assembly, bench testing, safety test and final process packaging.

Amtec Industry

Hayward, CA 3/2011 – 12/2011

Quality Control Testing Technician

Assemble control panel for solar industries commercial and burner control boiler management refinery boiler control pump control pneumatic valve control heater panel residential combiner boxes commercial combiner with monitoring capability sunpower box circuit breakers and weather station equipment. Conduct functional test using multimeter, verify connection point to point, torque test making sure all the screws are not loose cable testing check for wire gauging the sizes and also the spec visual testing for scratches and fabrication test measuring all angle of the boxes meets the specification pulling test make sure all connection is properly connected energized troubleshoot and checking parts specification details. Used schematic prints and drawings, collected data summary reports, labeled bill of materials and quality final inspection

Electronic Sensor Technology

Newbury Park, CA 4/2010 - 2/2011

Lab Technician

Assemble and disassemble electronics vapor analyzer, building circuit board soldering and re soldering resistors capacitor coil transducer memory chips led switches battery packs and also build actuator pumps cable harness and electro mechanical sub assembly making columns traps, detector cables, sampler injector and remote injector Jumper cables and chassi harnesses doing some high pressure test and leak test and Bluetooth connection. Material handling

Inventory clerk and some receiving work

*************@*****.*** phone #: 657-***-****

Skurka Aerospace Inc

Camarillo, CA 6/2008 - 4/2010

Test Technician and assembler

Assemble & disassemble ac and dc electric motors, starter generators speed pick up transducer fan blowers and tachometer for commercial aircraft military aircraft and ground vehicles antenna drive system naval ships system and space exploration. Conducting quality control test according to acceptance test procedure. Bench testing dielectric test insulation resistance test continuity test. checking wires connection and also check the right parts before go for functional test. Connect the unit to the dynamometer and energized with the 200 or more voltage and then loading test when you putting current using magtrol analyzer next step breaking torque test and

Pressure test and leak test at the same time when put the unit in the water with 40 to 1000 psi

For 3 or more hours making that’s there is no bubbles at all make sure all the rubber oil ring is installed. Oil test run the motor with max speed making sure that every single parts. Is proper and sealed

Contact this candidate