Mechanical Design Engineer

Naresh G, Mechanical Design Engineer ********************@*****.*** mobile: 830-***-****, 950-***-****

CAREER PROFILE:

Seeking a position as a piping engineer where I can apply my skills and knowledge in the field towards the growth and development of the organization

PROFESSIONAL EXPERIENCE:-

DESIGNATION : MECHANICAL DESIGN ENGINEER.

ORGANIZATION : SPUSHP STEEL, HYDERABAD.

DURATION : AUGUST 2014 TO TILL DATE.

JOB RESPONSIBILITIES (PEB DESIGN)

Responsible for preparing Approval Drawings / Shop Drawings / Erection Drawings by using AutoCAD software.

Preparing BOM In excel for drop in steel staircase according with study of worksheet, structural, architectural drawings and detailing manual.

Prepare design calculations.

Prepared materials take off (MTO) and Purchase Requisition for Mechanical Equipment’s.

Co-ordinate with design engineers and group head on any queries or difficulties raise during work and submit erection,shop drawings and BOM to the group head after making these ready for checking.

Coordinate with clients via mails, telephonic conversations.

Any queries occur in PIS or design I raise queries mail to concern department.

I make my internal plans to finish the work according to finished schedule and gives early warning to the group head if schedule cannot be met.

Correct any errors found and implements instructions provided by the group head or detailing checker after the job has been checked.

Prepare engineering release transmittal for erection drawings, shop details and BOM for concern department with which engineering dept. coordinate.

Ensure that the job file is well organized and updated.

Resolving the problems, interacting and co-ordination with design, erection & sales departments for smooth functioning of the project.

PROFESSIONAL EXPERIENCE:-

DESIGNATION : MECHANICAL DESIGN ENGINEER.

ORGANIZATION : LOKESH MACHINES LIMITED, BALANAGAR.

DURATION : JUNE 2013 – JULY 2014.

JOB RESPONSIBILITIES (MACHINE DESIGN)

Responsible for preparing Assembly Drawings, Shop Drawings of machine components.

Tolerance stack up analysis

Knowledge on Geometric dimensioning & tolerance.

Knowledge on the Process flow chart related to the Machinery Equipment from Design to Dispatch.

Preparing BOM of group assembly and spare part sketches of machinery equipment.

Prepare design calculations.

Prepared materials take off (MTO) and Purchase Requisition for Mechanical Equipment’s.

Co-ordinate with design engineers and group head on any queries or difficulties raise during work and submit erection,shop drawings and BOM to the group head after making these ready for checking.

Coordinate with clients via mails, telephonic conversations.

Any queries occur in PIS or design I raise queries mail to concern department.

I make my internal plans to finish the work according to finished schedule and gives early warning to the group head if schedule cannot be met.

Correct any errors found and implements instructions provided by the group head or detailing checker after the job has been checked.

Prepare engineering release transmittal for erection drawings, shop details and BOM for concern department with which engineering dept. coordinate.

Ensure that the job file is well organized and updated.

Resolving the problems, interacting and co-ordination with design, erection & sales departments for smooth functioning of the project.

MAJOR CLIENTS:

The regular clients of lokesh machines include

oAshok Leyland

oMahindra & Mahindra

oMahindra Navistar

oJohn Deere

oBharat Forge Limited

oVolvo Eiecher Commercial Vehicle Private Limited

oTata Motors

oCummins

oCaterpillar

oCrafts Automation Private Limited

oEscorts

oHonda

oMAN

PROFESSIONAL EXPERIENCE:-

DESIGNATION : MECHANICAL DESIGN ENGINEER.

ORGANIZATION : SS ENGINEERS, PUNE.

DURATION : Dec 2010 to April 2013

JOB RESPONSIBILITIES (PIPE LINE DESIGN)

Basic and detailed engineering of plant utilities like steam, condensate, water and compressed air

Preparation of GA Drawings and Isometrics based on P&ID

Sizing of pipelines and pressure drop calculations

Pipe wall thickness calculations as per ASME &IBR regulations

Study of heat and mass balance diagrams for a typical P&ID

Preparation of Bill of material and equipment data sheet for items required

Selection of material and class for pipes, flanges, fittings and valves as per ASME & IBR regulations

Pipe support and rack design,expansion loop design

Preparation of platform and railing drawings at various levels

Conversant with PFD’S and PID’S

Development and detailing of fabricated bends and reducers, etc.

Conversant with various piping design codes and practices as per ASME & IBR regulations

Coordination with clients and visits to site for details required for design of plant utilities

JOB RESPONSIBILITIES( PRESSURE PART DESIGN)

Preparation of pressure part assembly and equipment GAD’s (i.e. steam drum, boiler bank, water drum, down comer assembly, front and rear wall assembly, RH & LH side wall assembly, furnace headers,riser and releaser tube assembly) as per IBR regulations.

Sealing arrangement for front and side walls

Sealing of rear wall with side wall panels

Roof tube sealing arrangement

Super heater coil and header assembly

Economizer coil and header assembly

Heating surface calculation for furnace wall, super heater, economizer and boiler bank as per IBR regulations

Tube, coil, header thickness calculation as per IBR regulations

Steam drum, water drum, furnace headers, dished ends thickness calculations as per IBR regulations

Auxiliary and main foundation detail of a boiler

Preparation of main structure assembly of a boiler

ACEDAMIC PROJECT DETAILS (DIPLOMA ):

Title : WIND MILL FOR ELECTRIC POWER GENERATION.

Description : The main theme of the project is to know about Co efficient of performance of a Wind Mill, Wind data and energy estimation, Force on blades and Blade design.

ACEDAMIC PROJECT DETAILS (BTECH MINI Project):

Title : DESIGN AND MANUFACTURING OF AN ECCENTRIC BY:CASTING PROCESS.

Description : The main theme of a project was to learn about various advanced casting techniques.

ACEDAMIC PROJECT DETAILS (BTECH MAIN Project):

Title : DEVELOPMENT OF ASBESTOS FREE-FRICTION LINING MATERIAL FOR BRAKE PADS.

Description : For more than 80 years asbestos has been used as a friction material because of its good physical and chemical properties. However, due to the health hazards associated with its handling, it has lost favor and several alternative materials are being increasingly used. Thus, in this work, a non- asbestos friction material was developed using an agro-waste material base – Palm Kernel Shell (PKS)-along with other constituents. The designed brake pads were tested for wear, disk temperature rise and disk stopping time. When compared with the premium asbestos based commercial brake pad they were found to have performed satisfactorily.

SOFTWARE SKILLS:-

Designing software :- AUTOCAD, PRO E / CREO PARAMETRIC, CATIA V5

Office management :- MS office (word, excel and power point)

ACADEMIC SUMMARY:-

BACHELORS DEGREE IN MECHANICAL ENGINEERING from VIGNAN INSTITUTE OF TECHNOLOGY AND SCIENCE affiliated to JNTU in the year 2010

DIPLOMA IN MECHANICAL ENGINEERING from SANJAY GANDHI POLYTECHNIC affiliated to SBTET in the year 2007

X from ST. IGNATIUS HIGH SCHOOL affiliated to STATE BOARD OF SECONDARY EDUCATION in the year 2004

PERSONAL DETAILS:-

Father’s Name : SADANAND GUNREDDYPALLY

Date of Birth : 27th OCT 1988

Marital Status : SINGLE

Passport No. : J2822662

ADDRESS : H NO 4-113/3/A, PARSIGUTTA, SECUNDERABAD.

Nationality : INDIA

DECLARATION :-

I hereby declare that all the statements and information given by me in this application are true, correct and complete to the best of my knowledge and belief Date:

Place: HYDERABAD NARESH GUNREDDYPALLY

Contact this candidate