Pratik Pasalkar

Address:**** ********** *** *********** ** 01752* ac3f1d@r.postjobfree.com * 361-***-**** https://www.linkedin.com/in/pratikpasalkar

Objective:

Actively seeking Full-time position in the field of Embedded System / Hardware Design Engineering being an Enterprising, research savvy,fast adapting professional with good technical and hardware acumen. Education:

Texas A & M University Kingsville Master of Science in Electrical Engineering GPA: 3.41/4, Aug 2015-May 2017 University of Pune Bachelors of Engineering in Electronics & Telecommunications GPA: 3.50/4, Aug 2008-May 2014 Course Work:

Major I : VLSI Circuit Design Rapid Prototyping & ASIC Design Embedded System Design Microwave Engineering

Major II : Real Time DSP Digital Image Processing Speech Processing Computer Architecture

Minor : Broadband Network Wireless Communication Satellite Communication Neural Networks Work Experience:

Circuit Design Engineer (Raviraj Hi-tech Pvt Ltd.) - Pune, India. June 2014 - June 2015

Designed & developed complex electronics timer circuits for a water pump, turbo circuit for car & wireless home appliances switches.

Implemented MUX, combinational circuits, timer & counter. experienced with troubleshooting circuit board & component level failures.

Experienced with RTL simulation & verification, designed layout of ADC, DAC, Audio amplifier, Transformer Circuit and MOSFET.

Worked on low noise signal conditioning utilizing OPAMP, power managements, and various interfaces (I2C, SPI, Ethernet, CAN, etc.) Intern (Campus Component Ltd.) - Pune,India. June 2012 - Nov 2012

Studied design layouts and working principle of Gas, Temperature, Touch sensors and designed layout using Proteus software.

Designed PCB layout using Eagle software, Performed soldering on double & single side PCB by mounting active & passive components.

Analyzed performance of circuit in terms of noise, voltage & current using Spectrum Analyzer, Network Analyzer and Function Generator. Technical Skills:

Operating Systems: Linux, Windows XP, Windows 7, NOOBS, RASPBIAN.

Programming Languages: C, C#, Verilog, VHDL, System Verilog.

Scripting Languages: PERL, PYTHON, HTML, TCL.

EDA Tools: ModelSim, MATLAB, LabView, Proteus, MultiSim, Quartus, Xilinx, MPLAB, AutoCAD.

Test & Measurement Tools: CRO, DMM, OTDR, Spectrum Analyzer, Network Analyzer, Signal Generator, Function Generator.

Networking: OSI 7 Layer Model, TCP/IP, DNS, DHCP,LAN technologies, Switches, Cables, Bridges, OSPF, EIGRP, IGRP, RIP and RIPv2.

Other Skills: Self-motivated,Communication, Teamwork, Critical Thinking, Ability to Work Under Pressure, Time Management. Projects:

Power, Voltage and Current Analysis of 8-bit Ripple Carry Adder.Tools:(Magic, LTSPICE)

Designed layout of 8-bit ripple carry adder by applying design rules for Universal & Transmission gates in Magic (Open Source Software).

Obtained a Netlist from Magic and simulate in LTSPICE to observe an output of circuit in waveform and authenticated using truth table.

Measured performance in LTSPICE at each hierarchy level in terms of voltage, current, and power. Implemented ALU, Dual Port RAM and Data Memory through Verilog. Tools: (Quartus, ModelSim)

Created 16 bit ALU unit, Dual Port RAM consisting of two sets of address bus & data bus along with data memory of 512 bytes.

Validated RTL analysis in Quartus, created test bench and verified Simulated waveform output in ModelSim. Traffic Light Control System using FSM on FPGA (Spartan-3). Tool: (Xilinx)

Studied ASIC design flow synthesis and designed a code in VHDL to implement traffic light control system. Home Automation System using Raspberry Pi3. Scripting Language: (Python)

Developed a script on Raspberry Pi 3 to receive RF signal from the mobile phone to control relay switch.

Used 433MHz Superheterodyne RF Link transmitter and receiver to receive frequency from a mobile phone. Haptics-Based Robot for Hazard Control.(Wireless protocol used Zigbee) Tools: (Proteus,Eagle,MPLAB)

Designed an ATmega16 Microcontroller based wireless robot using RF module.

Built a DC Power supply of 12V,5A specification,performed power supply calculation and select 7812 regulator IC. Identification System for Dead Human beings using Dental Biometrics.Tool: (MATLAB)

Developed a code in MATLAB for identification of a dead human being by using teeth as a feature of identification.

Created a GUI to match a post-mortem radiograph with an antemortem radiograph. Ethernet Security System. Tools: (Proteus, Eagle, LabView, MPLAB)

Developed an Ethernet system to secure an office from one floor to another floor by means of Local Area Network.

Interfaced relay, LED display and electromagnetic lock to 8051 Microcontroller using MPLAB software. Analysis of Radiation patterns, Gain, Bandwidth, Impedance and Power of Helical, Yagi-Uda, Horn and Parabolic Reflector Antenna.

Performed connections of all antenna using antenna setup equipments and calculated Gain, Bandwidth, Impedance and Power.

Traced the radiation pattern of receiving antennas. Studied the comparison using performance of all antennas.