*

• Nationality

• Birth Date

• Status

• Mobile

• Phone

Ali Nassif

Mechanical Engineer

Personal Information

: Lebanese.

: **/**/****.

: Single.

:+965-********.

:+965-********.

• E-mail : ac3d55@r.postjobfree.com.

ac3d55@r.postjobfree.com.

• Driving License – Kuwait

Date of Issue: 22/08/2017

• Member in Kuwait Society of Engineers

Objectives

To pursue a challenging position in an Industry that will utilize my acquired skills, expertise and offer me further career development and mutual growth where I can gain experience, coordination skills and performing high quality work. Advanced Skills and Knowledge Areas

Training at (Bruxell International) since 23/07/2015 until 23/08/2015 in Kuwait.

• Knowledge about installation of HVAC systems (DX units & Package units Working at (Kuwait Finance House) as a Projects Coordinator-IT Projects Department- IT Sector in Free Zone since August 2009 until August 2013. My Principal Duties and Responsibilities include the following:-

• Manages all the project documentation produced by the project team and management According to KFH-Prince 2 Methodology.

• Coordinates with other departments, and /or projects to insure project success.

• Coordinating activities, resources, equipment and information.

• Liaising with vendors to identify and define project requirements, scope and objectives.

• Use project management tools to monitor working hours, budget, plans and money spend using petty cash.

• Issue all appropriate legal paperwork.

• Report and escalate to management as needed.

• Create and maintain comprehensive project documentation, plans and reports 2

Courses & Certification

Pump Technology.

This course is offered to enhance the knowledge and skills of participants who would like to understand piping system calculations. Pump classifications. Centrifugal pump construction. Pump performance curves, operating points, discharge regulation, similarity, speed variation, cavitation and water hammer phenomena. Pumps in series and parallel. Multi-stage pumps, axial flow pumps, Kaplan pumps, Fire pumps for fire protection (Codes and Standards), Fire pump pressure control. pump applications and introduction to pump station design. Project - 1: design and construction of two pumps connected in series and parallel. Projects- 2: design and construction of variable speed pump in a closed or open system. Design, selection, operation and maintenance of pumps. Viscosity effect on pump performance air entraining vortex effect. Priming of pumps. Design of pump stations. Fluid System Design.

This course is offered to enhance the knowledge and skills of participants who would like to understand design, selection, operation, and maintenance of fans, compressors, and blowers and theory and application of each type. Project – 1 involve the design and application of a ventilation system in building car parking. Projects-2 relates to hot water pipes distribution in a heating system, and chiller pipes sizing and system in HVAC applications. Pipeline engineering & pipe networks using Hardy Cross Technique “Using Darcy Equation”.

Hydraulic Circuits.

This course is offered to enhance the knowledge and skills of participants who would like to understand design of basic circuits, elements of hydraulic circuits and design factors, Positive displacement oil pumps as sources of hydraulic power, oil reservoirs, pipes, control valves: pressure, direction and flow control, fluid power actuators: hydraulic cylinders, hydraulic motors, standard symbols and graphical representation, basic hydraulic circuits and applications in practice. Refrigeration and HVAC Applications.

Introduction to refrigeration methods: Air refrigeration, steam jet, thermoelectric, absorption, vapor compression system, psychometric processes and cycles, cooling and heating loads, duct design, air conditioning systems, noise criteria, metering devices, compressors, evaporators, condensers, cooling towers. Refrigeration cycles, Multi- stage compression cycles, compressor types and selection, metering device selection, cooling coil design, Air handling unit design, condensing unit design, refrigerant piping design, chilled and hot water piping design, control devices, refrigeration system troubleshooting cold stores, computer software.

3

Thermal Power Stations.

This course is offered to enhance the knowledge and skills of participants who would like to understand systems and cycles used in electrical power generation. Overview of plants operating on fossil fuel, nuclear energy and solar energy. The main emphasis is on gas turbine, steam turbine, (CCGT) - combined cycle plants and traditional steam-generation plants burning fossil fuel such as natural gas or oil. Nuclear power generation and the steam generation systems, heat recovery systems, the condenser systems, pumps and other auxiliaries operations.

Engineering Economy.

This course is offered to enhance the knowledge and skills of participants who would like to understand basics principles and techniques of economic analysis of engineering project, time value of money, cost allocation and estimation, evaluation of engineering projects and investments, depreciation, inflation, bond and loan financing, after tax cash flow analysis, sensitivity analysis, selection among mutually exclusive alternatives using present worth, annual worth, internal rate of return, benefit-cost.

Plumbing Engineering.

Plumbing plays a major role in the construction field for every residential, commercial and industrial building. This course provides a good opportunity to understand how plumbing works in a practical and simple way. The course will highlight the different practical and theoretical topics, in addition to Case studies in the plumbing area. Swimming Pool's Design, Operation & Maintenance.

This course is offered to enhance the knowledge and skills of participants who would like to understand the design principals involved in various type of swimming pools, artificial leaks, Jacuzzi, water falls, fountains and field of water action. Preliminary, final plans, specifications, all design information (sizing, calculations, equipment selection) and reports submitted for approval to start construction are covered. Operation and maintenance procedures are listed.

4

Education & Qualifications

Bachelor Degree in Mechanical Engineering, Graduated from “Beirut Arab University” in Beirut, Lebanon since September 2007 until January 2017.

(Stop Studying from September 2009 until September 2013) Science Department Certificate, Graduated from “Al-Shaheen High School” in Kuwait (until July 2007).

Graduation Project

Successfully completed a graduation project about “SOLAR DESALINATION USING DOUBLE GLASS SOLAR STILL". Level achieved “Very Good”.

• AutoCAD.

Technical Skills

• HAP (Hourly Analysis Program HVAC System Design Software)

• Pipe Flow Expert.

• Inventor.

• SolidWorks.

• MS Office.

• Microsoft Project 2010.

Soft Skills

• Enhanced ability to listen with objectivity and logical analysis information.

• Continuously improve the working procedures and environment.

• Non-judgmental criticism and positive actions and effective working alone or as a co-operative team member.

• Hard worker and able to work under pressure.

• Excellent communication skills.

• Motivated and enthusiastic about developing good relations with others.

• Strong skills in office management.

• Excellent knowledge and use of Computers, Internet, and applications.

• Excellent dealing with networks computers.

• Fast and accurate English type writing.

Languages

• Arabic: Mother tongue.

• English: Very good in writing,speaking and listening. Interest

• Football, Readings, Traveling and surfing Internet 5

6

7

8

9

10

Contact this candidate