Project Mechanical Engineering
Resume:
M. Jayed Hossain
*** **** **** ******, ************, IN 46202
Phone: 317-***-****, ********@******.***, LinkedIn: https://www.linkedin.com/in/jayedhossain PROFILE
I am a MS graduate student in Mechanical Engineering with an excellent record of achievements, extensive research experience, and four years working experience as a maintenance engineer in heavy industry. EDUCATION
Purdue School of Engineering and Technology IUPUI Bangladesh University of Engineering Technology, Dhaka Master of Science in Mechanical Engineering Bachelor of Science in Mechanical Engineering May, 2018 (Expected) / GPA:3.95/4.0 March, 2012/ GPA: 3.44/4.0 TECHNICAL SKILLS
Software: MAXIMO, SAP, AUTOCAD, PTC CREO, ANSYS, MATLAB, LABVIEW and C-programing Professional Skills: Maintenance (PM, CM, EM), Inspection, Project Management (Planning, Budgeting, Purchasing & Execution), Leadership, Quality Control, Internal Audit, CMMS, FMEA, Safety (HIRA & OHSAS), FEA, GD&T.
EXPERIENCE
Purdue School Of Engineering And Technology IUPUI August 2016 - Present Graduate Research Assistant
Frictional Analysis of cartilage tissue using Bruker Tribolab machine.
Determination of the amount of wear and the change of mechanical properties of cartilage tissue due to compressive loading and motion.
Develop a protocol for experimental procedure and analysis.
Analysis of the composite behavior of cartilage subjected to compressive loading.
Measurement of hydroxyproline content using a LABCONCO freeze dryer and Biotech reader.
Image analysis and measurement of the percentage of wear of cartilage due to compressive loading using a stereomicroscope with digital camera and MATLAB.
Impact load analysis between cartilage and metal using LABVIEW software, KISTLER accelerometer and load cell.
Optimization of laser treatment of cartilage tissue using photochemical crosslinking. Karnaphuli Fertilizer Company Limited (KAFCO) August 2012 – August 2016 Maintenance Engineer
Inspection and maintenance of cooling towers, steam turbines, boiler, boiler feed water pump, air compressor, water treatment plant, dual fuel diesel engine, overhead crane, various pumps and utility valves, and ammonia and urea processing plant.
Performed troubleshooting by analyzing gauge reading and vibrational data.
Carried out inspections using DPT(dye penetrant test), MPI(magnetic particle inspection tests), hydro tests, and air tests.
Project management duties included planning, budgeting, material purchasing, and supervising the repair of a filter water tank (Capacity:14000m3) and installation of a 500m 16ʺ underground raw water line.
Leadership role required communication with group members and other departments, and gave proper instruction in all situations.
Used SAP software to purchase spare parts and machinery.
Quality checked of spare parts and machinery.
Performed FMEA (Failure Mode and Effect Analysis) during any modification of any process system. 2
Understanding of P & ID and equipment’s blueprints before attempting maintenance work.
Used MAXIMO to keep a record of all maintenance and modifications.
Actively participated in Internal Audit committee.
HIRA (Hazard Identification and Risk Assessment) compliance by following OHSAS health and safety manual.
Replaced rotor of steam turbine generator (10MW, Manufacturer: Nuovo Pignone) and pump (12300m3/h, Manufacturer: Turbomechanica) and adjusted to proper radial, axial alignment and axial play.
Supervised major maintenance of Boiler (Capacity: 95Ton/hr, Manufacturer: Macchi) in Turn Around-2015.
Fabrication and modification of machine parts with Lathe and CNC machine.
Developed maintenance plans for machinery including engineering specifications and cost analysis. Bangladesh Steel Re-rolling Mill (BSRM) August 2011-Spetember 2011 Intern
Submitted daily Reports of the rerolling mill.
Worked with different hydraulic and pneumatic control system.
Present a report about the re-mill to the management and gave a recommendation about the safety of the industries. PROJECTS
Frictional analysis and determination of mechanical properties of cartilage under compressive loading. Project funded by NSF. 2016-2018
Impact load analysis of cartilage tissue using a drop tower and determination of mechanical properties changes due to impact loading. Project funded by NSF. 2017-2018
3D modeling of gear transmission system using PTC CREO and friction and load analysis using ANSYS software. Class project. 2017
3D modeling of AC-40 air circulator using PTC CREO with GD&T. Class project. 2017
NC simulation of a gear pump using PTC CREO. Class project. 2017
Modeled a hybrid composite for car hood using ANSYS ACP and PTC CREO software. Class project. 2017
CFD analysis and Optimization of CPU Heat Sink using ANSYS FLUENT. FEA Class project. 2017
Installation of 16ʺ Underground Raw Water Line, KAFCO. 2016
Repair of Filtered Water Tank (1400m3), KAFCO. 2014
In Vivo Measurement of Mechanical Properties of Human Long Bone using Sonic Sound. Undergraduate thesis project. 2012
Automatic Measurement of Static Friction Measurement. Class project. 2010 SPECIALTY TRAINING
Corrosion Engineering Training at KAFCO. Trainer: Giel Notten, NIT Consultancy. 2014
Maintenance & Troubleshooting of Compressors and Turbines at Training Institute of Chemical Industries(TICI), Bangladesh. 2013
OHSAS Safety Training at KAFCO. 2012
ACCOMPLISHMENTS AND AWARDS
Successful Completion of Turn Around-2015.
Best Engineer Award at KAFCO-2015.
Award for best project in ICME- 2009 at BUET.
Contact this candidate