Manager Customer

Donna F. Horan

Inspection Supervisor / Calibration Manager

256-***-**** **************@*****.*** 4069 Braeswood Drive, Apt. 5 Huntsville, AL 35802

Summary

** ***** ** ******* ******* / Assurance experience including Entry Level to Management. 12 years of Calibration experience including Entry Level to Management.

Credentials

ISO Internal Auditing – Certificate Received

Statistical Analysis I – Certificate Received

Statistical Analysis II – Certificate Received

Leadership Training – Non-certificate Course

How to Build a Better Team – Certificate Received

Experience

Inspection Supervisor, Turner Medical Inc., Athens, AL 35611

Supervised Quality Inspection department of approximately 20 employees. This included but not limited to:

Reviewing daily activities and product to ensure that all products met Customer requirements.

Reviewed Non-conformances and processed to the MRB (Material Review Board) for disposition.

Reviewed, promoted, and disciplined within the department as needed.

Participated in Internal Auditing to ensure all Customer, ISO, and FDA requirements were being met. (Certification received).

Participated in FTQ (First Time Quality) Events to improve product flow from the Inspection Department.

Participated in various Lean Manufacturing Events to assist in increasing flow within the department.

Participated in FDA and ISO registration audits resulting in full Certification without findings.

Performed review of all new and repeat jobs that included but not limited to verifying all gauges were available prior to the Production Run. This included all Customer Supplied Gauges. Verifying all specifications that were called out on the blueprint drawing were readily available for the inspection department. Creating a Gauge List that listed all necessary gauges for every job in the shop that would assist in preparing the job both on the manufacturing floor as well as the Inspection Department

[2010-2017]

Calibration Manager, Turner Medical Inc., Athens, AL 35611

Managed Calibration System of approximately 9,750 active gauges. This included:

Entering all gauges into the Calibration Software (Gage Trak) with appropriate tolerances, calibration due dates, and failures.

Scheduling On-site and Off-site calibrations with the Outside Vendor chosen to perform these actions. This included scheduling 2 days per month for on-site each month to calibrate IMTE such as Micrometers, Calipers, Optical Comparators, Height Gages, etc.

Pulled all gauges that needed to be Calibrated off site which included all Thread Ring and Thread Plug Gauges, Temperature Gauges, Voltage meters, etc.

Requesting internal gauges to be manufacture to assist in easing inspection of several dimensions. Attribute gauges.

Ordering replacement members for any Thread Gage that fell out of specification.

Create Deficiency reports for any gauges that failed calibration.

Reduction in Calibration cost by extending gauges that the calibration seal was not broken during the previous cycle allowing the gauge to be used an additional 3 months to a year depending on the gauge type and application it was used for.

[2010-2017]

Final Inspector / Calibration Technician, Accellent, Inc., Huntsville, AL 35811

Final Inspection of product for the Medical Device and Aerospace industry. Managed the Calibration System using Gage Trak Software which includes:

Final inspection of Medical Device and Aerospace components and assemblies using various IMTE including Micrometers, Calipers, Optical Comparator, Height Gauges, Tesa Hite Gage, OGP Vision Machine, Go / No-go Thread Ring, Thread Plug Gauges, Go / No-go Gauge Pins, and various Customer Supplied and Internally made gauges to ensure all Customer specifications were within specified tolerances as required.

Entered approximately 1,800 gauges into the Gage Trak Software to be able to manage monthly and annual calibrations. Scheduled On-site and Off-Site calibrations using an Outside Vendor chosen to perform calibrations. Wrote up deficiency reports for any out of tolerance gauges.

[2005-2010]

Quality Manager, Automatic Machine Products, Co., [Attleboro, MA 02703]

Managed Quality Control Department in this Automotive / Refrigeration Shut-off Valve manufacturer. This included:

Managing 17 employees to ensure all Inspection requirements were being met to the AS9200 standards of the organization.

Customer correspondence regarding complaints, failures, or positive feedback.

Investigation of all non-conforming product internally or the result of a Customer Complaint.

Monitoring all internal non-conformances and preparing for the MRB (Material Review Board) for disposition.

Schedule Internal Audits for the Auditing Team.

Prepare Metrics on Customer Complaints, Positive Feedback, Internal Non-Conformances, and Customer Returns for quarterly Management Reviews.

Other Skills

Microsoft Office including Microsoft Word, Excel, Power Point etc.

Creating Queries using Excel.

Data Entry

Scheduling

References available upon request

[1990-2004]

Contact this candidate