MOHAMMED MISBAH NABI

ac2g7w@r.postjobfree.com, 203-***-****

PROFILE:

Master of Science in Electrical Engineering from Lawrence Technological University in Jan/2017 with a 3.7 GPA.

Around 2 years of professional experience as a Test Engineer performing system testing and validation.

Co-op experience as an Associate Engineer Intern working on Vehicle Control System implementation using CAN bus protocol.

Knowledge of Vehicle Communication protocols such as CAN, LIN, MOST and ETHERNET.

Experienced in the use of RF testing tools, Voltmeter, Oscilloscope, Multimeters, Navigation and Mapping tools.

Good understanding in each phase of Software Testing Life Cycle (STLC).

Tested various infotainment features such as Media, Speech Recognition using different testing techniques.

Capture and Log Issues into defect management tools such as JIRA and Bugzilla.

Efficient knowledge of CDMA, GSM/GPRS/EDGE, LTE, WI-FI, and Bluetooth technologies.

Experienced of using Vehicle spy analyzing the CAN messages, CANalyzer and CANoe.

EDUCATION

Master of Science in Electrical Engineering Jan 15- Jan 17

Lawrence Technological University (LTU), Michigan

Relevant courses: Digital Communications, Digital Signal Processing, Control Systems, Computer Networks.

Bachelor of Science in Electronics and Communication Engineering, Aug 10-May 14

Jawaharlal Nehru Technological University, Hyderabad, India.

Relevant courses: Embedded Systems, Microprocessors and Microcontrollers, Antenna and Wave Propagation.

PROFESSIONAL EXPERIENCE

Infotainment Test Engineer Mar 17-present

Integra Technologies, Wilmington, DE

Executed in-vehicle and bench testing including manual and automated testing.

Identified systematic issues affecting system performance and created strategies to improve performance.

Involved in reviewing test results for new test cases of Bluetooth and navigation.

Vehicle function testing by NeoVI tool and CAN message evaluation.

Analyzed the user requirement specifications for infotainment modules and implemented sanity and smoke testing.

Executed various test cases for Bluetooth profiles such as HFP, PBAP, AVRCP, MAP, and A2DP.

Logged and tracked defects using JIRA.

Test Engineer July 14-Dec 14

Druva Automobile and Controls Pvt Ltd. India

Performed functional testing on AM & FM and Bluetooth.

Tested features of Radio like Scan, Seek, Direct Tune, and Preset.

Executed various test cases for Bluetooth profiles such as HFP, PBAP, AVRCP, MAP and A2DP.

Analyzed user requirement specifications and implemented smoke, sanity testing.

Tested various HMI features by giving voice commands.

RF Test Engineer May 13- Jun 14

Aircel India Pvt Ltd

Performed Testing for single cell sites and cluster using Probe of Huawei.

Optimized serving sites by changing antenna tilts and orientation to improve overall throughput.

Tested intra cell handover (with clockwise & anticlockwise) & inter cell handover.

Drive test for the initial installation with test frequency.

Drive test with commercial frequencies and collect data across the coverage area.

Check for Handovers within the sectors and neighboring sites.

3G pre-optimization drive and Post Optimization drive.

Associate Engineer Intern Jan 13- May 13

Transceiver Technologies Pvt Ltd, Hyderabad

Analyzed data transmission using CAN bus protocol.

Executed CAN Network Communication to control accessories like Remote operations, headlight on/off, door locks and performed test on engine speed and braking system to analyze variation of speed.

Developed a distributed control system to communicate between the sensors and actuators of different ECUs.

Monitored CAN messages and observed the impact of these messages on the module.

Executed various Diagnostic services like Read DTC, Clear DTC, Read DID, Run Diagnostics Routines.

ACADEMIC PROJECTS

Data Acquisition System with Controller Area Network and SD Card.

Implemented a high-speed data acquisition system using Mega32 microcontrollers and a Controller Area Network (CAN).

Used multiple transmitter nodes to acquire data from sensors and transmit the data in packets over a CAN bus. Each transmitter consists of a Mega32 microcontroller, an external Analog-to-Digital converter, a CAN controller and a CAN transceiver.

Advanced user controlled Roof Top Antenna Signal Tracking System

Designed roof top antenna tracking system to track signal using IR sensor.

Determined the direction of propagation of a signal.

Integrated Microcontroller and H-Bridge module for signal detection and relay.

Successfully tracked signal for various frequencies.

Filter Design for Noise Removal in Digital Images (MATLAB)

Successfully designed six different types of filters and generated Noise in MATLAB.

Implemented the Graphical User Interface (GUI).

Calculated the MSE and PSNR values for the filters.

Implemented all the designs codes in MATLAB and compared the results.

TECHNICAL SKILLS

Software Proficiency : MATLAB, Simulink, Lab VIEW, DSPACE and Multisim.

Programming Languages : C, XML, Ladder Logic (PLC)

Application Software : MS Word, MS Excel and MS PowerPoint

Ancillary Skills : DFMEA, DVP&R, CANoe/CANalyzer, Vehicle Spy

Bug Tracking Tool : JIRA, BUGZILLA

HONOURS AND AWARDS

Graduate certificate in Telecommunications Engineering.

Designed a Smart Robotic Arm in association with the Robotics Academy of USA.

Paper presentation on ‘Remote Monitoring of ECG’ at a national level Tech Fest ‘Technophilia’.

REFERENCES

Available upon request

Contact this candidate