LUIS PERDOMO

*** ********** ** ***** 757-***-****

Celina, Ohio 45822 ac1rhl@r.postjobfree.com

To obtain the Electrical Engineer position in a fast paced and challenged environment utilizing exceptional skills on design, planning, testing, reporting and solving high technology problems.

TECHNICAL SKILLS

Electromagnetic theory, emission and immunity compliance testing and EMC design

Write EMC qualification test procedure, automating EMC test, test setup, verification, and

calibration

Performer test, EMI data analysis and troubleshooting, and write test report

Proficient with EMC military, ISO, FCC, IEC, UL, IEEE, ANSI and CISPR standard specifications

for product test, design and development

EMC automation software: Teseq C5, Haefely, Tile, Chase, Schaffner and some in house programs

Working knowledge of grounding, bonding and shielding

EMI Survey

Radiation Hazard Survey

Safety, environmental and reliability test

Electronic: Spice, Analogue, digital electronic and embedded systems design

Testing: Circuit analysis, hardware fixture design, troubleshooting and automation

test

Languages: C, C++, Visual Basic and LabView

Platforms: Windows 00/NT/Xp/Vista/Windows 7, UNIX, MS-DOS

Familiarity with Network analyzer, Spectrum Analyzers, Oscilloscope, Multimeters, Signal Generator, Power Meter, DAQ, PLC, Amplifiers, Antennas, Lightning Generator, Current Probe, RF Coupler,

Signal Generator, Power meter, Surge Generator, ESD Generator and Radhaz meter.

Extreme attention to detail

Team working, support the design and development team

Design automated test equipment (ATE)

PROFESSIONAL EXPERIENCE

Crown Equipment Corporation 2012- Present

Electrical Engineer-EMC

Perform EMC tasks as planning, testing, troubleshooting, redesigning, test set up and reporting on Lift Trucks

Perform EMC laboratory duties as chamber calibration, purchase parts, design test configuration for traction, steering and hydraulic.

The main standard apply here is the EN12895

The CANalyzer, CANape, PCAN Explorer and other software tools were used to monitoring truck parameters during testing.

Custom Manufacturing and Engineering Inc, FL 2011- 2012

Test Engineer

Implement Automated Test Equipment (ATE) production testing of power supplies.

Perform the tasks of researching, designing, developing, and testing electronic components and systems

Develop the tester, direct software system testing procedure, programming, and documentation.

Test varied customer electronics equipment and interpret/apply complex EMC/EMI industry standards ( Mil-Spec.) to products being tested for compliance

Allied Technology Group, Inc, Virginia 2008-2011

EMC/EMI and Electromagnetic Radiation Engineer

Performed radio frequency parameters evaluation of radios, transmission lines, and antennas on HF, VHF and UHF frequencies.

Planned, tested, reported and project solution of electromagnetic interference survey on shipboard and shore stations. These surveys consisted on radio frequency immunity test and emission test using military standards Mil-STD-1605, Mil-STD-1310, CIM-10550-25B, NAVSEA STD 407-***-****, FCC Part 80, Mil-STD-461, Mil-STD 464 and Mil-STD 449.

Planned projects of bonding, shielding and grounding on shipboard.

Developed projects to resolve interference problems among system on shipboard

Projected, tested, and reported electromagnetic radiation hazard survey on shipboard

Electromagnetic radiation hazard environment certification (HERP, HERO and HERF).

Determined the specific absorption rate (SAR) compliance by measure the maximum permissible exposure limit (MPE) of the electric field, magnetic field, induced current and contact current on HF, VHF and UHF frequencies.

Designed solution to electromagnetic radiation hazard problems.

Performed HF,VHF and UHF antennas installation projects

Developed shipboard engineering project of communication radios, antenna mast foundations, transmission lines, bonding, grounding, lighting and SOVTs

Recommended frequency planning according to the EMI survey

● Measured antennas, radios, and transmission lines parameters such as sweep, VSWR, impedance, radiation pattern and electric field.

Participated in design reviews with an eye towards design for compliance

Square D, NC 2005-2008

EMC Engineer

Planned test, tested, reported and mitigation of emission tests (radiated, conductive) and immunity tests (Radiated, Surge, ESD, Burst, Ring, Damped, Conducted and Magnetic) of industrial products.

Performed EMC plan, test and report according to FCC and European standards (FCC, UL, IEC, CISPR, IEEE, and ANSI). A summary of the test standards that I am familiar is: FCC part 15; IEC (61000-4-2, 61000-4-3, 61000-4-4, 61000-4-5, 61000-4-6, 61000-4-8, 61000-4-9, 61000-5-2, 60947-5-2, and 60947-1); CISPR (11, 16-1-2, 16-1-1, 16-2-4, 16-2-2, and 22); IEEE (C62.41-1, C 62.41-2); ANSI (C 63-40 and C63.16); and UL (943, 489, 60950, 1699, 991, 1053)

Redesigned cable running, electronic boards, power supplies and filter to meet EMC standards.

Accomplished automation EMC testing software using Visual Basic, Lab View, Tile, Chase, Haefely and Schaffner

Evaluated the laboratory accreditation, performed the anechoic chamber calibration and generated of calibration files for laboratory test equipment and test fixtures.

Troubleshoot test failures and recommend design changes to meet compliance requirements.

EDUCATION

ISPJAE, CUJAE UNIVERSITY OF HAVANA - Havana, Cuba

Electrical/Electronic Engineer/Telecommunication (Equivalent of BS in USA)

UNIVERSITY OF HAVANA- HAVANA, CUBA

Postgraduate Computer Engineering (Equivalent to MS USA)

Additional Education: Postgraduate studies in: Hardware, software and Electromagnetic Compatibility

(Some of them are Assembly language, C, C++, Visual Basic, Access, Microsoft Office, analog electronic, digital electronic and Microprocessors).

MCSE, MCSA, and MCP on Microsoft Windows 2000 2002

EMC Engineer Narte Certification 2007

PROFESSIONAL AFFILIATIONS

Member: IEEE and EMC Society

FOREIGN LANGUAGES:

Spanish: Fluent (Native Language)

Contact this candidate