Post Job Free
Sign in

Process Engineer

Location:
Friendswood, TX
Posted:
July 10, 2017

Contact this candidate

Resume:

MOHAMMAD SARIEH

***** ***** **** **.

Friendswood, TX 77546

Cell Phone: 832-***-****

Email: *******@*****.***

Page 1 of 4

I am legally authorized to work in USA without the requirement of sponsorship now or later. I hold a permanent residence visa (green card).

PROFILE

Sr. Process Engineer with ten years of experience, mainly with EPC Contractor. Skilled in FEED/ Detailed Process Engineering Design projects for brown and green fields, Technical Proposals, Field Support and Commissioning of Oil and Gas facilities.

KEY SKILLS & KNOWLEDGE AREAS

• FEED/ EPC Oil and Gas

Projects/ Proposals

• Process Simulation

(HYSYS, PIPESIM,

FLARENET, PIPENET)

• Hydraulics and Surge

Analysis

• Process Engineering

calculations, equipment

sizing,

• HAZOP and SIL

• Project Management

• Pre-commissioning/

Commissioning

• International Codes and

Standards (API, Shell DEP,

BP, NFPA)

• Proposals

• Process Safety, PSV sizing

and selection.

• PFDs and PIDs

PROFESSIONAL EXPERIENCE

Consolidated Contractors International Company, Abu Dhabi- UAE www.ccc.gr

January 2007

May 2017

Project Nasr Full Field Development Project - Package 3 Onshore Das Works Date July 2015 – Up to date

Location Abu Dhabi-UAE

Client Abu Dhabi Marine Operating Company (ADMA-OPCO) Contract Value USD 150 Million

Project

Description

EPC Works for new MOL and Pig Receiver on Das Island; upgrade of 7 Separation Trains

(HP and LP Separators, HP and LP Scrubbers) and 3 Spheroids (3 phase separators) to cater for increased capacity and new feeds, Installation of New Crude Charge Pumps, Revamp of 4 Crude Stabilization and Sweetening Units; Installation of New Stripped Product Pumps, Installation of 2 New Flares (HP and LP); New Boiler package and New Condensate Bay Adequacy checks, studies, and revamp where required of existing plant systems (lines and instruments, relief and blow down systems) to meet increased production demand. Execution of complicated tie-ins, with ZERO Shutdown philosophy, including hot taps.

Role Senior Process Engineer (Seconded to Chiyoda CCC Engineering Office www.ccel.ae) Duties Developed the steady state and dynamic state simulation of the system on HYSYS and defining the case studies.

Prepared Process Design Basis and Process calculation Report. Prepared block flow diagram, Heat and material balance and Process flow diagram Defined and prepared Flare and PSV adequacy study and flare headers and flare stacks replacement package.

Lead Flare Package Vendor during project phase.

Project FCP Gas Slug Catcher and Associated Facilities Date June 2014 – June 2015

Location North Rumaila, Iraq

Client Shell Iraq Petroleum Development B.V. (Shell) Project

Description

E&P part for the FCP Gas Slug Catcher and associated utility facilities for the North Rumaila, Majnoon field in Iraq.

MOHAMMAD SARIEH

16915 Sandy Reef CT.

Friendswood, TX 77546

Cell Phone: 832-***-****

Email: *******@*****.***

Page 2 of 4

Role Lead Process Engineer (Seconded to Chiyoda CCC Engineering Office www.ccel.ae ) Duties Lead the process of preparation of design deliverables Ensured appropriate checking & review of all documents / drawings before release at any Revision status. Participated in project review meetings/ HAZOP and SIL meetings. Progress monitoring to scheduled completion of engineering documents. Coordination with the other Engineering disciplines, client and vendors Control of Quality of engineering documents with regard to Quality assurance basis. Project FEED Study of BuHasa-3rd New IA Compressor Date February 2014 – June 2014

Location Abu Dhabi-UAE

Client Abu Dhabi Gas Industries Ltd (GASCO)

Project

Description

FEED study to install the 3rd new Instrument Air Compressor Package and associated facilities to meet the increased instrument air / plant air consumption due to other retrofit projects in the plant over the years.

Role Lead Process Engineer (Seconded to Chiyoda CCC Engineering Office www.ccel.ae) Duties Lead the process of preparation of design deliverables Ensured appropriate checking & review of all documents / drawings before release at any Revision status. Attend project review meetings/ HAZOP and SIL meetings Project EMC for Southern fields for PDO (Bahja Cluster) Date August 2012 – Aug 2013

Location Muscat- Oman

Client Petroleum Development Oman (PDO)

Contract Value USD 800 million

Project

Description

seven-year engineering and maintenance services contract (EMC) to the joint venture between Wood Group and Consolidated Contractors Company (CCC) set up to provide operations and maintenance services for the oil and gas and petrochemicals industries in Oman

Role Lead Process Engineer (seconded to Wood Group CCC office) Duties Lead Process Engineer for the South EPCM Contract involved in review/ approve of process deliverables prepared by job engineer. Executed number of Facility Change Requests (FCPs), FEED (Define) and EPC (Execute) projects. Involved in, Design and Safety reviews, conducted for the projects.

1. Bahja FEED/Detail Engineering Integrity Project 2. Rima Fire Water Refurbishment Project

Project 100MBD DAS Facilities Upgrade Project

Date September 2011 – July 2012

Location Abu Dhabi-UAE

Client Abu Dhabi Marine Operating Company (ADMA-OPCO) Contract Value USD 90 Million

Project

Description

Installation of 2 new Separation Trains and upgrade of five existing Trains on DAS Island to increase the throughput capacity by 100 MBD. In addition to installation of a new Cold Stripping Unit in order to meet the stock conditions of RVP and H2S content. Scope covered includes: Sour Crude Charge pumps and Stripped Crude product Pumps; 3 Phase HP Separators, 3 Phase LP Separators, 3 Phase 4th Stage Separators, Separator internals upgrade, HP and LP Scrubbers, Sour Crude Charge Heaters, Cold Stripping Tower, New Closed Drain System, New Boiler package and New Condensate. Replacement and update of existing Separator/ Column internals, and Installing new Demulsifier and Corrosion Inhibitor injection packages and relocation of some existing MOHAMMAD SARIEH

16915 Sandy Reef CT.

Friendswood, TX 77546

Cell Phone: 832-***-****

Email: *******@*****.***

Page 3 of 4

ones. Adequacy checks, studies, and revamp where required of existing plant to meet increased production demand. Execution of complicated tie-ins, with ZERO Shutdown philosophy, including hot taps

Role Sr. Process Engineer

Duties Developed the simulation of the process using HYSYS and generated Heat and Material Balance.

Prepared PFDs and UFDs and PIDs.

Updated Project Design Basis.

Reviewed Hydraulic Calculation and prepared Hydraulic report. Participated in HAZOP and SIL meetings.

Reviewed Vendor offers.

Prepared an adequacy study of the existing PSVs for existing equipment. Project EPC for Bab Thamama-G and Habshan-2 - 1.8 MMBOPD Phase-1 Development Project Date December 2010 – July 2011

Location Abu Dhabi- UAE

Client Abu Dhabi Company for Onshore Oil Operation (ADCO) Contract Value USD 683 million

Project

Description

A project undertaken to increase Production at Bab field by development of the Habshan-2 and Thamama-G production zones. The expected sustainable production from these two zones is 80 MBOPD. Project covers Engineering, procurement and construction related to production wells tie-ins and flow lines connecting Productions Wells to 4 new RDSs associated with several transfer lines, tie-ins of 54 Water Injection Wells, a total of around 950 Kms pipelines, Separators, Vessels, Tanks, Heaters, various pumps, flare stacks, chemical injection systems, air compressors, vapor recovery compressors, Nitrogen generator, DCS/ESD/F'&'G and SCADA systems, Electrical power generation including overhead lines, switchgears, transformers, UPS, etc., Valves, Telecom systems and other associated works.

Role Process Engineer (seconded to NPCC office www.npcc.ae) Duties Prepared/ updated process documents: Process Description, Emergency Shutdown Philosophy, Operating & Control Philosophy, Equipment List, Line sizing /List, Instrument datasheets, Cause and Effect diagram, Utility Consumption Report. Prepared BCDS demolition scope Cause & Effect Diagrams. Integrated BCDS new facilities C&ED with existing C&ED. Project Al Khafji Phase -1 Development Project

Date Jan 2007 – Sep 2010

Location Abu Dhabi- UAE/ Saudi Arabia-KSA

Client Kuwait Joint Operating Company – KJO

Contract Value USD 600 Million

Project

Description

The project includes new crude separation system (LP Separators), Gas compression (LP and MP), Propane Refrigeration System, Condensate Separators, Molecular Sieve Dehydration for Condensate and for Gas, Mercury Removal Unit, LTS Condensate Separator, Condensate Stabilizer Towers, NGL Recovery and Dew Pointing (De- ethanizer) Lift Gas Compression (90 bars) and pipeline, New Flares and Relieving Systems, Waste Heat Recovery and Hot Oil System, MP and LP Fuel Gas Systems, Instrument and Plant Air Units, Nitrogen generation Unit, Diesel Supply System, Chemical Injection Units, Fresh Water, irrigation Water, Fire Water, Open and Closed Drain Systems. The capacity with the new plan will be 750,000 BPD produced liquid

(including up to 50% water cut) and 115.5 MMSCFD of produced gas. Role Process Engineer

MOHAMMAD SARIEH

16915 Sandy Reef CT.

Friendswood, TX 77546

Cell Phone: 832-***-****

Email: *******@*****.***

Page 4 of 4

Duties Prepared and up-dated PFDs, P&IDs, and Line List/ Cause and Effect diagram Updated Simulation on HYSYS and Heat and Material Balance. Prepared Instrument/ Equipment/ valves datasheets

Participated in HAZOP and SIL meetings

Carried out Surge analysis for pipeline system using PIPENET Prepared Operating Manual for different units, pre-commissioning, commissioning, start up and handing over procedures, and commissioning system dossiers Checked and reviewed Vendor Documents.

Took part in Pre-commissioning and Commissioning planning & scheduling Prepared pre-commissioning, commissioning, start up, and test run execution plans with assistance of the Commissioning Manager

Prepared punch list using P&IDs, equipment vendor drawings, and other related data available for the project

Controlled Process Start-Up, Shut down, and troubleshooting for fire water system. EDUCATION

American University of Sharjah (AUS), UAE

Bachelor of Science in Chemical Engineering

Sep 2002 to June 2006

RELEVANT COURSES/ SEMINARS AND WORKSHOPS

• EHY223 Aspen HYSYS Dynamics: Introduction to Dynamic Modeling by Aspen Tech

• EHY901 Multi- Stage Compressors- Conducting Operational and Safety Studies using Dynamic Analysis by Aspen Tech

• EHX1011 Design and Rate Shell and Tube Heat Exchangers by Aspen Tech

• Professional Project Management Program (PMP) at Cambridge Education

• Oil and Gas Chemical Processes at American University of Sharjah

• Leadership skills (Motivation, Problem Solving, Negotiation, Leadership and Management, Teamwork, Delegation) Seminars and Workshops at CCC

• Contractual Obligations & Rights Seminar and Workshop at CCC



Contact this candidate