Engineer Design

Aneesh Kachroo E-mail:

******.*******@*****.***

Ph. +91-917*******

Career Objective:

To achieve excellence through dedicated efforts & positive attitude by

being resourceful, innovative and flexible.

Working Experience 2.10 Years

Current Job Profile

Working as Design and Support Engineer in QUALCOMM, on Contract.

Previous Experience

Worked in VVDN Technology as a Hardware Design Engineer (Sep 9, 2010 to

April 15, 2013)

Job Profile

Responsible for End to END product development.

Responsible for studying and writing the Design specifications for the

board as per customer requirements

Selection of major ICs and components for the Board from different

Vendors

Responsible for carrying Schematic entries using EDA tool such as

Orcad, Altium.

Providing PCB Layout guidelines to PCB layout designer during PCB

design cycle.

Generating net list and Bill of material (BoM) and verifying it.

Generating Gerber and reviewing it.

Writing the Test plans and Test report for the embedded Boards.

Complete Board bring-up and testing of various hardware interfaces on

the board.

Carrying out the Design Validation Test (DVT) analysis for different

Interfaces on Board.

Signal Integrity Analysis basics using Hyperlynx.

Had hand on experience in RF calibration with ATsuite tool and

hardware Debugging of RF section.

Technical Skills:

Schematic and PCB Altium, Cadence Design tool (ORCAD, ALLEGRO)

design Tools

RF Calibration tool ATsuite

Simulation Tools Hyperlynx, LTSpice

Debugging Tools BDI, JTAG

Memory interfaces SDRAM, DDR/DDR-II/DDR- III SDRAM, EMMC, NAND Flash

and NOR Flash, EEPROM, uSD Card, SATA.

Peripheral interfaces 10/100/1000 Mbps Ethernet, RS-232/485 interface,

USB interface, UART, m PCI

Standards I2C, SPI, MII, RMII, RGMII, GMII, LOCAL BUS, USB,

HDMI, VGA SD Card, Power Management and Power

Sequencing, SIM and UIM.

Database Management Agile

Projects Handling at QUALCOMM

Responsible for Design and Support activities for Class -A Family (MDM9X15,

APQ8064, MDM9X30) and MSM8x10/12.

Projects Done at VVDN Technology

DVR (Digital Video Recorder)

Configuration: DVR is a consumer electronics that records audio/video in a

digital format to a disk drive, USB flash drive, SD memory card or other

local or networked mass storage device.

Digital video recorder is configured for security applications; it records

audio/video signals from cameras for detection and documentation purposes.

The Board is based on the TMS320DM81XX series from TI

Responsibility- Drafting PRD (Product requirement document) by

understanding the requirements and then drafting of HDD (Hardware Design

Document) for the costumer. Making Test Plans, Making Schematics, Doing

Placement for the Layout, Board Bring up, Sitting with the Mechanical Guy

and Designing the Mechanical for the Card.

TDU-7 (Transmission Distribution Unit)

Configuration: Atheros Processor Card is Mother Board for TDU (Transmission

Distribution Unit) being used in the world GSM transmission section.

The Board is based on the AR71XX Processor from Atheros; the design is

compatible for the low end processor in the same series.

It is a six layer board using network processor from Atheros AR71XX, 2

Micrel 88e60XX Switch being used for the 7 Ethernet ports. It uses five

replica sections of AP/RU.

Responsibility- Making requirements Documents, making Design Documents,

Making Test Plans, Making Schematics, Doing Placement for the Layout for

the new Revision,Board Bring up, Sitting with the Mechanical Guy and

Designing the Mechanical for the Card.

NGMR (Next Generation Mobile Router)

Configuration: Next Generation Mobile Router is to enable communication

backhaul from a next-generation, consolidated IP/MPLS backbone network to

E1 and Internet Protocol (IP) traffic respectively at cell site for 2G, 3G

and 4G traffic. The Board is based on the WinPath3 SuperLite from PMC-

Sierra (Wintegra).

Responsibility- Drafting PRD (Product requirement document) by

understanding the requirements and then drafting of HDD (Hardware Design

Document) for the costumer.

BTS RU (BTS RU)

Configuration: It is a six layer board using network processor from Atheros

AR71XX, Micrel 88e60XX is used as the 3 port Ethernet Switch. It interfaces

with the Ethernet MAC of Atheros through GMII interface, 16MB Flash based

on SPI serial protocol is used as boot device, 64MB DDR2 SDRAM (32MB x 2

Nos) is used for packet and data storage for processor execution and mini

PCI interface with RF card.

Responsibility - Making requirements Documents, making Design Documents,

Making Test Plans, and Doing Board Bring up, Hardware debugging and making

new Revision with required changes.

Standalone RU/AP - Standalone Radio Unit/Access Point

Need - Wireless connectivity for P2P and P2M.

Solution - RU (Radio Unit) transmits and receives the Ethernet Signal and

converts the received Ethernet signals into wireless signals @ BSC/BTS

Configuration: It is a six layer board using network processor from Atheros

AR71XX, VSC86XX from Vitesse is used as a Single port 10/100/1000Mbps

Ethernet PHY. It interfaces with the Ethernet MAC of Atheros through RGMII

interface, 16MB Flash based on SPI serial protocol is used as boot device,

64MB DDR2 SDRAM (32MB x 2 Nos) is used for packet and data storage for

processor execution and mini PCI interface with RF card.

Responsibility - Doing Board Bring up, Hardware debugging and making new

Revision with changes such as power section etc.

Gigabit PoE - Power over Ethernet @ 1000BASE-T Ethernet.

Need - Gigabit link for Radio Unit (RU).

Solution - Designed a 24V Gigabit PoE for Radio Unit.

Responsibility - To design a PCB board using PoE Magnetics for Data

transfer.

1. Home Gateway

Application: Home Gateway used as to provide wireless connectivity to

customer premises.

Configuration: RTL81XX Wireless Access Point processor and RTL81XX WLAN

including 4/8MB SPI Flash, 32MB SDRAM, Four 10/100Base-TX,one USB port

using multilayer PCB( 4 Layer) .

Responsibility - Testing of Cards, carrying out Board Bring up, Hardware

debugging.

Ethernet Consumer Premises Equipment (CPE)

Application: Wireless-N 2T2R High Gain Ethernet Adapter as coverage

extender.

Configuration: RTL81XX Wireless Access Point processor and RTL81XX WLAN

controller from Realtek, including 4 MB SPI Flash, 32MB SDRAM,

One10/100Base-TX port.

Responsibility - Testing of Cards, carrying out Board Bring up, Hardware

debugging.

Summer Training

. Project Title: Understanding GSM technologies at Aircel Limited,

Gurgaon.

Period: May'09- July'09

. Project Title: Understanding Network Planning at Bharti Airtel Limited,

Gurgaon

Period: Jun'08-July 08

. Project Title: DATA (LL) and Transmission at Bharti Airtel Limited,

Gurgaon.

Period: May'08-June 08

Academic Projects

. Implemented AES Voice Encryption and Decryption, in 2009-2010.

. Designed an Electronic Voting Machine and fabricated on PCB, in 2008-

2009.

. Designed Robotic Car with analog controls, in 2007-2008

. Designed a Digital Combinational Lock and fabricated on PCB, in 2007-

2008.

. GSM Technologies: Studied basic principle and applications, in 2008-

2009.

Academics:

Electronics (B.tech) with an aggregate 74.5% from Narsee Monjee

Institute of Management Studies, Mumbai. (July, 2010)

Senior Secondary- Secured 77.6% marks in 12th standard from Blue Bells

Sr. Sec. School, Gurgaon affiliated to C.B.S.E, in 2006.

Matriculation Result Secured 78.8% marks in 10th standard from Blue

Bells Sr. Sec. School, Gurgaon affiliated to C.B.S.E, in 2004.

Others: Learning Deutsche.

Personal Skills:

Keen Learner

Perseverance

Adaptability

Team member

Hobbies:

Painting, Reading, Vocabulary

Personal Details:

Father's Name : Sh. Ashwani Kachroo

Date of Birth : 14th July 1988

Phone no. : 091********

E-mail : ******.*******@*****.***

Permanent

Address : House No. 1399A, Sector 10A,

Gurgaon-122001,

Haryana, India

Date:

Place: Hyderabad

(Aneesh Kachroo)

Contact this candidate