High School Equipment

James H. Bryant

Cell: 409-***-****

e-mail:**********@*****.***

SOLID STATE

(1) DC Drives

a. GE units

b. Reliance

c. Enerpro

(2) SCR Primary side choppers

(3) Secondary high current hockey puck

(4) Secondary high current hockey puck reversing

(5) Variable frequency drives

(6) PC Board repair experience

a. double sided plated through as well as single sided boards

(7) TEST EQUIPMENT

a. scopes

b. meters

c. comparators

d. meggers

e. hypot

(8) Installed amplifiers,public address systems

(9) Small phone systems

(10) TV cameras,various types of recorders used in survelliance work

(11) Solid state welders, gas and diesel, as well as control cards

(12)

(13) RADIO WORK

a. UHF,VHF, LOS

b. time multiplex

c. SHF troposcatter

GENERAL CONSTRUCTION

(1)Experience from slab up

a. conduit from 4 inch down to 1/2 inch

b. tray work

c. wire pulling in tray and conduit

d. lights, hardware, panels

e. terminations

f. Plc work

g. instrumentation

h.heat trace terms

SWITCH GEAR EXPIERENCE

(1) Cutler Hammer

(2) ITE

(3) GE

(4) Westinghouse

(5) Allen Bradley

(6) Furnas

(7) SQ-D

(8) Telemecanique

(9) Numerous other off-brand types

(10) 13,800, 4160, 2300, 480 gear and hardware

(11) Multilins

(12) Ground fault systems

(13) Reduced voltage

(14) Slip-ring and synchronous starters up to several hundred horse power

(15) Have repaired oil-filled and dry type transformers.

(16) Have cleaned OCBs and most types of oil drying and testing equipment.

(17) Fabricated bus bar both copper and alu

MOTOR EXPIERENCE

(1) Have assembled and disassembled motors (AC, DC, slip-ring, synchronous) from1/20HP up to 4000HP.

(2) Repaired Babbitt and sleeve motors

(3) Also have assembled shaker motors.

(4) Have wound up to 4000HP synchronous, 3000HP AC.

(5) Have wound armatures and field pieces for DC up 1250HP.

(6) Worked on and wound slip-ring motors up to 400HP rotor and stator.

(7) Have extensive single-phase experience up to about 60HP.

(8) Have repaired many types generator sets, repaired large AC generators, 3-phase self-excited, synchronous and most

types of DC generators.

(9) Rewound oil-type and dry-type transformers

(10) Extensive experience on LeTourneau type equipment, generators, and switch-gears.

(11) Spent years in a motor shop environment on a day-to-day basis as a shop hand as well shop foreman, salesman and

owner.

(12) Have repaired welding equipment, rotary, solid state, wire feeders, set ups for flange welders, spot welders and battery chargers

(13) Very extensive 3000amp to 12000amp rectifiers experience. Have set up and repaired reversing units using primary

choppers as well as hockey puck units using secondary reversing. Have also set up old rotary type rectifiers.

OVERHEAD CRANES

(1) Serviced and repaired up to about 200 ton overhead cranes down to small single-phase chain hoists.

(2) Worked on AC, DC, slip-ring and radio controlled units, DeMag, Kranco, Coffing, Yale, Detroit and many others. s as well as kept up on OSHA spec book and equipment.

BOILERS

(1) Have worked on infra-red eye and flame-rod type burner controls.

(2) Have torn down and repaired and installed high pressure multi-stage pumps and piping. Have machined inner parts

and brought these pumps back up to specs. Experience with carbon ceramic type seals, gland type and various types of slurry seals.

AIR CONDITIONING

(1) Worked with units up to about 60 tons, worked on chillers, heat exchangers, coolers, water knockouts and so on.

(2) Have changed out units, scrubbed lines, checked for acid level and put back on line. I am familiar with present federal

guidelines for handling freons. Have current freon handling license.

(3) Familiar with controls and trouble-shooting of control systems for both 3-phase and single-phase systems. I am familiar

with several types ice machines, along with various types of display boxes.

AIR COMPRESSORS

(1) Worked on old recip. models such as Ingersoll and a few others. Have serviced Ingersoll twist-air and Joy twist-air

units. Changed oil knockout filter, replaced seals and bearings.

HYDRAULICS

(1) Familiar with Racine, Fjelman, Oil Gear and several other types of units.

HIGH VOLTAGE

(1) Stress cones up to 13800

(2) Transformers repair and rewind

(3) Switch gear trouble-shooting and repair

(4) Motor and generator rewind and repair up to 13800

SUPERVISORY EXPERIENCE

(1) Worked as superintendent on fast paced high pressure jobs.

(2) Have served as foreman and general foreman

(3) Extensive print reading experience.

(4) Hold Texas journeyman license

EDUCATION

(1)High School

(2)Numerous tech schools

(3)supervision school

(4)Electronics in the service

(5)TWIC card

(6)OQ training for pipeline insp

(7)Extensive pipeline work const and maint

(8)Ext PLC Term

(9)Over 30 years exp in plants in the Baton Rouge,Golden Triangle,Houston and various other states

(10)DCS work

(11)Package building work(such as Powell)

(12)Some college courses

(13)microsoft office

Contact this candidate