Grand Rapids Maintenance
Resume:
Paul Peck
Marne, MI, *****
Objective
Seeking a position in a company where I can use my maintenance management experience in order to
help my employer better serve their customers and to make the service department operate safely and
efficiently while attaining job satisfaction, growing in the company, and learning new things.
Work History
Grand Rapids Chair
625 Chestnut St SW
Grand Rapids, MI 49503
2010-Current
-Looking for a new position as current company is moving.
Duties: Responsible for all building and grounds maintenance. Experienced with the repair/upkeep for air,
hydraulic, and Electrical (110-220-480 three phase) lines. Responsible for the repair of all equipment.
Coordinates the ordering of products through contractors and suppliers. Repairs presses, benders, welders
(tig and mig), powder coat paint lines, Hi-Lo’s (gas and electric), lighting and stretch wrap machines.
Wages: $20/hour
Northwest Tool and Die (6 + years)
2980 3 Mile Road
Grand Rapids, MI 49405
2002-2008
-Lost job due to company closing
Duties: Building and ground maintenance, repair of all equipment, presses, CNC, drill presses, boring
mills, Welding all types of tool steels, ARC, MIG, and TIG welding
Wages: $23/hour
Advanced Tooling Systems (5 years, 7 months)
1166 7 Mile
Grand Rapids, MI 49405
1996-2002
-Lost job due to corporate downsizing
Duties: CNC Repair (Droop & Rein, Giddings & Lewis, Dahlin), flame treatment of steel, tool steel
welding, TIG and MIG welding, Repair of the following mills: Cincinatti, K&T, Willis micro-cut, and
Bridgeport mills. Repaired Carlton, Cincinnati, and Bickford Drill presses, as well as Grand Rapids
grinders. All phases of electric up to 440 volts. Work on various air compressors, Leroy and Sullair
compressors, tub grinders, and all magnetic systems for grinders. Worked on wire burners (Mitsubishi and
Hitachi), Kamatsu plasma cutters, band saws of all types, rollout Bolster systems for presses.
Stephenson & Lawyer Inc. (9 years)
3831 Patterson S.E.
Grand Rapids, MI 49405
1987-1996
Duties: Work on preventative maintenance program, pneumatic systems, work on Ingersoll and water jet
cutters, presses (air and hydraulic), part revolution, and full revolution of clutch presses, ruff strippers,
Frecken and Kirfel saws, band saws, pattern saws, hot wire cutters, lamination equipment, infra-red
heating systems, tape cutters, all types of building and security equipment for the premises, boilers, PC
controllers, all phases of electricity, plumbing, conveyor systems, buffing equipment, and ventilation
systems.
Pasco (2 years)
1340 Monroe N.W.
Grand Rapids, MI 49405
1985-1987
Duties: Repaired: Jaybird feeders, roll feeders, coil reels, Chicago and National riveters. Repaired
electric and gas Hi-Lo’s, batteries, spot welders, proximity sensors, light bars, maintenance presses up to
750 tons, pullbacks, as well as Sullair and Kaiser compressors. Worked with: DC motors and controllers,
conveyors, boilers, refrigerated air dryers, 110, 220, 200 three phase, 440 three phase, and air stakers.
Electric: all phases
Spinners: all phases
Walker Industries (9 years)
1988 Alpine
Grand Rapids, MI 49405
Duties: ARC, MIG, TIG, and automatic welding. Operated and maintained Hi-Lo’s including all phases of
electric. Troubleshooting and repair of presses and boilers (Cleaver-Brooks).
Education
Coopersville High School
198 East Street
Coopersville, MI 49404
Graduated in 1975
Kent Skills Center
1655 East Beltline NE
Grand Rapids, MI 49525
Studied heating and Ventilation
Grand Rapids Junior College
143 Bostwick NE
Grand Rapids, MI 49503
S.P.C. Training
Licensed in Ground Water Run-off by the state of Michigan
School of Fluid Power
References
Tom Novitsky
Employee
Darryl Scott
Co-worker
5084 Angermeyer Rd.
Ravenna, MI 49451
Contact this candidate