Engineer High School

Rod Isler

Elyria, *****, Ohio, US

Mobile Phone: 440-***-****

Secondary Phone:

E-mail: *********@*****.***

[pic]

OBJECTIVE

My immediate career objective is to gain steady, full time employment with

an established company. i feel that i have many skills that would be a

benefit to any company that employs me. i would like to learn every aspect

of the position i accept and continue to move up the company ladder.

[pic]

WORK EXPERIENCE

Quality Control Technician

July 2011 - present

Elyria Foundry Elyria, OH

I have several duties in my role as Quality Inspector. i work directly with

the Quality Manager, Senior Quality Engineer, and the Chief Inspector.

My duties vary from final point inspection in the foundry to spectro

chemistry and metallography in the lab.

While performing final point inspections i check for quality issues in

castings such as shrink, gas diffusions, and sand inclusions. Mostly my

inspections are performed after the inspector assigned to those specific

castings has gone over it and approved it to be shipped. This is to ensure

nothing was missed.

While in the lab i operate a spectrometer to check ductile and gray iron

samples for proper chemistry of specific elements that pertain to that

specific type of iron and casting. i maintain and calibrate that same

machine.

With other ductile iron samples i sand them with a belt sander then polish

them with an orbital sander. from there i perform microscopy. i view them

under a microscope to look at the physical properties of the iron to check

for grain structure and nodularity.

Sometimes i have to etch these samples. this allows me to view the graphite

structure and distribution. During this process i also check for pearlites

and ferrites.

Depending on chemistry and physical properties i write a quarrantine ticket

to pull a job into a hold to be reviewed by the senior quality engineer.

I operate a carbon analyzer with a known carbon standard powder against

parts of samples to compare data with the spectrometer and the data cast.

I am a member of the internal audit team. With this i perform a single

audit per week to various departments to issue corrective action responses

if required.

I break chills to measure carbides.

I operate a boroscope to look into certain channels of castings if there

are certain issues.

I cut various types of "blocks" with one of two band saws that I operate. I

cut sections of various castings in to specific sizes to look for a

particular defect. I also perform routine maintenance on the saws.

I currently operate a haas cnc lathe to machine the "blocks" I cut into

"bars" of specific specs. I set the lathe up depending on the size and type

of bar I will be machining as well as changing tooling and taking needed

axis measurements.

I operate tow motors several times a week.

I completed a hass programming course on September 26th of 2012.

Heavy Equipment Operator

December 2010 - June 2011

Lorain County Recycling Lorain, OH

My duties were to operate an excavator and a skid steer primarily. i also

acted as yard mechanic.

Operated an excavator to move cars and full grapples full of various types

of scrap metals and load into appropriate hoppers.

Operated a skid steer to move various things around the yard and warehouse.

I stripped cars of components like batteries and catalytic converters.

Operated equipment such as a bailer, chop saw, scale, and banding machine.

Service Technician

March 2007 - December 2010

Turners Automotive Lorain, OH

My main duties were to diagnose and repair automobiles

Diagnosing computerized engine controls and driveability problems.

Explaining to customers the problems with their vehicles and why certain

repairs are needed.

Operation of various hand and air tools.

Operation of acetylene torches

Mig welding

Operating a brake lathe

Road testing vehicles to make sure repairs made corrected customer problems

Used Inventory Technician

January 2003 - March 2007

Spitzer Autoworld Grafton, OH

Responsible for safety checking all used inventory coming onto the lot for

immediate sale.

I performed general maintenance on all used inventory.

Safety checks to specific points such as complete brake systems and

exhaust.

Operation of various hand and air tools.

Proper disposal of used fluids.

Proper evacuation and reclaiming of refrigerant.

Operating a brake lathe

Road test vehicles after repairs were made.

Front End Technician

June 1999 - January 2003

Conrads Total Car care Lorain, OH

Performed in depth advanced wheel alignments.

Diagnosed and replaced front end parts.

Performed four wheel and thrust angle alignments adjusting for castor,

camber, and toe angles.

Operated hand and air tools

Operated acetylene torches

Tire ricking

Tire mounting and installation using air powered tired machine.

Operated harmonic balancer.

[pic]

EDUCATION

Certification, Professional Automotive Career Training,

May 1999 - June 2000

Cuyahoga Community College Cleveland, OH

Studied and completed certificate programs in advanced wheel alignment,

braked, engine repair, and steering and suspension

High School or equivalent, General Studies,

September 1992 - June 1996

Clearview High School Lorain, OH

Completed four years of general studies as well as shop, art and automotive

classes. graduated and received a diploma

[pic]

CERTIFICATION

P.A.C.T certificate in brake system diagnostics and repair

May 1999

Cuyahoga Community College

Completed and received a certificate in brake system diagnostics and repair

P.A.C.T certificate in steering and suspension

September 1999

Cuyahoga Community College

Completed and received a certificate in diagnosing and repairing steering

and suspension

P.A.C.T certificate in advanced wheel alignment

January 2000

Cuyahoga Community College

Completed and received a certificate in advanced wheel alignment procedures

P.A.C.T certificate in engine repair

June 2000

Cuyahoga Community College

Completed and received a certificate in engine diagnostics and repair

[pic]

HASS Factory Outlet

September 2012

Completed course and received a certificate of recognition in CNC Lathe

operation.

Contact this candidate