production supervisor

Joaquin Herrera

*** ****** ***

Lemont Il. **439

Hp- 1-630-***-****

Mobile. 1-630-***-****

E mail **********@*******.***

General supervisor of rolling (Keystone-Calumet) (2005 to 2012)

Chicago Heights Il 60441.

Managed, roll shop.

Duties

Trained roll turners, and assigned work orders, to accommodate for incoming

rolling cycles. Making sure, we had all the passes available, for all the sections to

be rolled. Assign all the rolls for the current cycle.

Ordered rolls from different roll manufacturers, also ordered castings and guide

equipment for the mill...

Trained roller supervisors, on how to roll different products in X country mill.

Squares, from 0.750” To 1.563” round and sharp corner. (Flats, from 1.000”x

0.250”. to 4.000” x 0.250” Up to 1.000” thick. Rounds and especial sections.

Helped develop procedures for the re-heat furnace on how to set up different ratios

for regular carbon chemistries and also some alloy like 4140,5160 and some

others.

Helped maintenance department on planning outages every 6 months and also

assist on major break downs Mechanical and Electrical.

Major achievement in this mill was developing a pass design for 5” x 5” billets

from a 4”x 4” Keeping the same product line.

(Report directly to the president of the company, Mr. Larry Leonard and also Mr.

Jerry Rich. Phone 1-708-***-**** Ext.4424

General supervisor of rolling. ( Sheffield Steel Corp. ) 1999 To 2005

Joliet Il. 60435.

Managed roll shop.

Develop roll cards for every set of rolls that we had at that time .,Develop a set up

sheets for new sections, making sure that we had the right tooling

To cut a different passes on the rolls available for a product family to be rolled at

that time,kept enough supply of rolls to run the mill efficiently.

Ordered tooling for the roll shop and the mill.

Develop a training for a new roller supervisors .in a X country mill.

Family products like squares. Flats, rounds,hexes.and special sections..

Major achivment in this mill was, converting 3 stands from fiber bearings to

A roller bearings. Because we had problems holding tight tolerance on some

products.

Set up a differernt procedures for the reheat furnace implementing differernt ratios

for differernt grades of steel.

Reported to Operations Manager. ( Frank Di Falco )

Day shift supervisor. ( Austeel Lemont ) 1993 to 1999

Lemont Il. 60439

Managed a X country mill,with 14 stds. Ran most rebar, from ” to

1 3/8”also ran some plain rounds ” to 2 ” Sqrs 1 1/8” to 2 ” RC and

Also some flats 1 ” to 3” width x ” to 1” Thick

Mainly training all the mill personal,in varios areas. From Re heat furnace

Speed pulpit, build up area,aqnd finishing end.

Major achivment in this mill was going form a X country mill to in line mill

All roller bearings, from 14 stds. To 18 stds. In line, using the same pass

Design for the products.

Reported to the superintendet ( Conrad Strassel )

Thomas Steel Corp. ( 1983 to 1993 ) Lemont Il. 60439

Roller su pervisor for 9 years, trained speed pulpit operators, heaters, and set up

people on the floor. Set the mill up to spec to roll different products

Such as, angles, flats, rounds.re bar and squares. Started training on pass design

and R factors. Worked with roll shop supervisor on pass lay out and pass available

for, the rolls that we had to accommodate rolling cycles.

Reported to Mill Superintendent. ( Huge Wallace ).

Lemont manufacturing, Ceca Corp. (1977 to 1983) Lemont IL. 60439

Started as Janitor, and worked my way up to production in the mill from finishing

end to re heat furnace, held different positions from cobble cutter

Second helper, first helper, mill operator,heater,pulpit operator, asst. roller

Up to fill as roller supervisor.

Everything that I have done (All hands on)

I am also bilingual. ( Spanish & English)

Looking for a roller supervisor position.

Education: High school Diploma

Studies: Course on rolling practices and pass design. ( Canada )

Contact this candidate