Electrical Engineer Design
Resume:
Electrical Engineer
Resume keywords summary: Mixed signal RF digital ADS PA inductor
Please log in to see the contact information!
Work Experience
Experience level: 2-5 years
Profile/Cover Letter: Mijung Roperti
1567 Tartarian Way, San Jose, CA 95129
U.S. Citizen
Tel. 408-***-****
Cell 510-***-****
abqeda@r.postjobfree.com
GPA: 3.73
OBJECTIVE: Seeking a mixed signal/RF engineer position.
SKILLS:
RF IC design: Design and simulate 65 nm integrated CMOS Power Amplifier (PA) and investigating Doherty PA. Design, layout and optimize the inductor design to achieve high Quality Factor on the Agilent ADS and Momentum.
Spectrum analysis: Analyzed the spectrum of the Direct Digital Frequency Synthesizer (DDFS) on the Master s thesis.
Lab equipment and Testing: Tested wireless power transfer using a Network Analyzer. Tested, analyzed and troubleshot transistor characteristics, filters and logic gates with oscilloscope, signal generator and DVOM meter.
Knowledge of RF theory and component: Smith Chart, VSWR, Harmonic Balance (HB), Return loss, Gain, S-parameter, phase noise, Phase locked loop (PLL), Power Amplifier (PA), Low Noise Amplifier (LNA), Automatic Gain Control (AGC), mixer, oscillator and filters.
Knowledge of Microelectronics: MOSFET and BJT.
Knowledge of Signal processing.
PSpice: Designed and simulated a band-gap voltage regulator which contains amplifier, rectifier and thermal protection, using PSpice.
PCB board: Designed and soldered a waveform generator and troubleshot its functionality.
Synopsys EDA design tool (Cosmos, Hercules and HSPICE): Designed the schematic and the layout of a ring oscillator.
VHDL: Designed and simulated multiplier, sequence recognizer and cache memory in VHDL on Xilinx ISE tool and ModelSim.
ASIC design: Altera s ASIC design tool (Nios II and QUARTUS II).
Embedded Firmware design: Experienced in using Altera s Nios II.
Microprocessor program: Logical troubleshooter making the Intelligent Motion System (IMS) operate and programming microprocessor language.
Computer communication network: Ethereal, DNS, routing, ATM, Frame Relay, TCP/IP and SONET.
Automation program: Proficient in automation programming on PERL platform; proven track record of programming laser inscribing lines for annealing and etching process of Photovoltaic (PV) cell.
Semiconductor equipment: Supported in developing complex semiconductor equipments, which requires knowledge of mechanical, electrical and software fields.
Software: ADS, PERL, MATLAB, C++, Orcad Capture, PSPICE, VHDL, Synopsys, Alliance CAD tool, HSPICE.
FPGA: Created FPGA-based Co-Processors for DSPs using Model Based Techniques (XILINX hands-on training workshop).
Modeling and Optimization: Parametric and Optimal Design of Microelectromechanical Systems (MEMS) on the MatLab.
Audited Quantum laser optic and Plasma physics.
VOLUNTEER EXPERIENCE:
San Francisco State University San Francisco, CA
RF IC Design Engineer Apr. 2009 to present
Design and simulate 65 nm integrated CMOS Doherty Power Amplifier (PA).
Agilent ADS and Momentum: Self-taught ADS and Momentum. Design and simulate RF IC components in schematic and Momentum layout.
o Gave a presentation on inductor design procedure in ADS and Momentum to the Lab for Analog Radio-frequency Integrated Circuit (LARIC) group in Electrical Engineering department.
o Optimize the inductor design to achieve higher Quality Factor Q.
o Document the design, layout and simulation procedures as an internal manual.
EMPLOYMENT:
NanoGram Corporation Milpitas, CA
Programmer/Translator Mar. 2008 to Jan. 2009
Programmed laser inscribing lines for annealing and etching process of Photovoltaic (PV) cell on PERL platform.
Programmed on microprocessor language and troubleshot Intelligent Motion System (IMS) on the XY translator.
Translated the languages of Korean and English to support the development of the semiconductor equipment to produce Photovoltaic (PV) cells and Thin film LCD panels.
Laminated silicon and SOI wafers to the glass using encapsulant.
Walnut Creek Honda Walnut Creek, CA
Mechanic (departed to go to school) Apr. 2005 to Mar. 2006
Provided automotive maintenance services.
Diagnosed malfunctioning components.
Recommended preventative services.
WheelWorks Livermore, CA
Mechanic Jul. 2004 to May. 2005
Provided automotive maintenance services.
Diagnosed malfunctioning components.
Recommended preventative services.
EDUCATION:
Master of Science in Electronics Engineering, San Francisco State University in August, 2009.
Bachelor of Science in Physics, Dong-A University in Busan, South Korea.
Training: Completed Automotive Technology, Los Medanos College in Pittsburg, CA
Completed UC Berkeley Extension Courses
- Nuclear Power Engineering: Nuclear plant structure
- Radiation Biophysics: Measurement of radiation dosage as a nuclear medicine.
AWARD AND ORGANIZATION:
Luigi & Luigia Franco Scholarship
IEEE Computer Society Scholarship
Rene Marxheimer Memorial Scholarship
IEEE student member 2007
References and portfolio are available upon request.
No submited work experiences
Background and Experience
Education Level: Master's Degree
School Name: SFSU
Major: Electrical Engineer
City: San Francisco
Country: USA
Graduation Date: 20/08/2009
Description: Not Specified
Languages
Language Level
English Fluent
Job Preferences
Job Category: 3g RF Design WCDMA UMTS Job
Job Type: Any Job Type
Job Status: Flexible
Desired Salary: $0 Unspecified
Desired Location: Not Specified
Willing to Relocate: No
Contact this candidate