Welder/Fitter/Grinder (Spokane, Wa)
abpho9@r.postjobfree.com
Anthony L. Larsen
**** *. ******* *******, ** 99201
abpho9@r.postjobfree.com
SKILLS:
General Experience
Computer Operation
Windows 95, 2000, XP
Ten key touch
Tape Measure Use
Crane Operation / 5 ton to 25 ton / push and remote controlled
Hand held Power Tools; Grinder, Drills, Saws, Stud Guns, ECT.
Forklift Operation
Welding Experience
.035
.045
1/16
Hard-wire or duel shield
Stick welding
Carbon Air-Arc cutting
All positions
Fabrication Experience
Measuring
Saw cutting
Torch cutting
Mag-Drill and Mill press drilling
Punch Press and Lathe machine operation
Grinding Experience
Hard-Disk, Soft-Pad and Sanding Disk skill
Quality joint welding and finishing sanding
Quality Pipe, I-beam, plate, channel, and tube grinding
Quality material repair grinding
Fitting Experience
Blue-print reading
Material layout
Straightening experience
Squaring off work piece with Speed square, carpenter square and levels
Jig Construction
Experience
Star Steel Metal Fabricators
Welder/Fabricator
06/2012 to 11/2012
509-***-**** / Spokane Valley, Washington 99212
Constructed Structural pieces and quality railings using saws, torches, shears, drill press and punch press. Lay-ed out material from blue-prints to fabricate, fit, weld and quality finish grinding. Operated cranes (5 ton) and forklifts to load, unload trucks and to position or rotate work piece. Welded Various thickness of steel from 1/8 to 3 Inch using .035, .045, and 1/16 duel-shielded and hard-wire. Used cutting torches to heat and straighten material, cut or cope work pieces.
Metals Fabrication Co.
Welder/ Grinder
08/2009 to 4/2010
509-***-**** / Airway Heights Spokane, Washington 99001
Welded using 1/16 wire; mainly welded 3/8 welds or CJPs, operated 25 ton remote controlled cranes to Load and Unload trucks and to position or rotate work piece. Finish welded structural steel beams for office buildings. Operated stud guns and welding machines with material ranging from in. to 3 in. thick, used torches to straighten or cope material, finish grinding using 10 in. Hard-disk and sanding disk.
REMCON Equipment
Fabricator/ Grinder
07/2007 to 6/2009
509-***-**** / Airway Heights Spokane, Washington 99001
Fabricated material using Saws, Drill Press, Brake Press, Shear, Lay-ed out material from blue-print using tape measure, try-square, Carpenter square and used center punch for hole marking.
Assisted painter in Finish grinding, wire-brush clean up and finish paint, assisted welders in fitting and jig construction
Education
Oxarc School of Welding
Intermediate to advanced welding training
06/2007 to 9/2007
509-***-**** / Spokane, Washington 99202
Graduated and received AWS / WABO Certificate
Accumulated 316 hrs on-hand training
Trained in operation of various sizes of grinders for Finish product grinding
Spokane Community College
Beginner Welding and Grinding practices
10/2005 to 5/2007
509-***-**** / Spokane, Washington 99224
Steel heating and welding theory, blue-print reading and material lay out and fabrication and fitting techniques.
Wire-feed and stick welding introduction
Machine operation and Hand held power tools introduction.
Measuring and square off techniques
Fabrication Math
References
Bjoren / Star Steel Shop Foreman
Todd Mathison / Metals Fabrication Co. Foreman
Dennis Lux / REMCON Equipment GM