certified welder
Resume:
Salvador Jauregui
El Paso, Texas 79936
915-***-**** (home)
************@*****.***
Resume of Work Experience
ManTech International Corporation Certified Welder
*****-* Sullyfield Circle, Suite 100
Chantilly, Virginia 20151
November 6, 2011 - February 6, 2013
As member of the deployed civilian support services, deployed to the
Kandahar region of Afghanistan, and other Forward Observation Bases.
Certifications received in welding Route Clearance Vehicles, stainless
steel, and 110 18 stick & MIG. In the capacity of certified welder, I
performed combination welding assignments on all military support vehicles,
and all other military support equipment as assigned. Additional duties and
responsibilities included fabrication of steel and metal pieces as assigned
in compliance with government/military codes.
Also when there was no welding or fabrication I done mechanic's such as .
Removed/Repaired: engines, transmissions, frame rails, body assemblies,
dash and control assemblies, transfer cases, drive assemblies, hydraulic
systems and components, steering and suspension components, wire looms,
body wiring harnesses, differentials, brakes, pneumatic air brakes,
electrical sensors and related wiring harnesses, power control boxes, glow
plugs, and electronic and electrical components. A/C components, seating
and safety harness assemblies.
El Paso County Sheriff's Department Maintenance Technician
El Paso, Texas
August 8, 2011 - October 14, 2011
Under the supervision of the lead maintenance technician, and in
compliance with applicable blueprints and schematics, weld by way of MIG,
TIG, and ARC processes, steel doors, sally-ports, gates, steel door frames,
and stainless steel and aluminum equipment. Additional duties and
responsibilities included installation and repair of electrical and
mechanical devices.
General Dynamics Welder II/Combination Welder
Seattle, Washington
April 18, 2011 - May 25, 2011
Welded, fabricated, and repaired ballistic steel parts for the
Stryker Armored Personnel Carrier, and the M1A2 Abrams tank. Welding
assignments consisted of Flux Core Arc Welding and Shielded Metal Arc
Welding processes. In addition, welding assignments also included Tungsten
Inert Gas processes. Welding rod usage for these assignments included the
6010, 6011, 7018 welding rods and MIG Flux Core Wire .035.
Ysleta Independent School District Combination Welder
El Paso, Texas
March 1997 - January 2010
Welded, fabricated, and repaired mild steel, stainless steel, and
aluminum structures, including field bleachers, metal canopies, metal
storage units, portable classroom units, and fabricated and installed metal
roofs on several campuses. Fabricated and repaired kitchen and cafeteria
equipment, and fabricated, welded, and repaired boiler-room equipment and
parts. Welding assignments were completed via compliance with blueprints
and building code specifications with application of MIG, TIG, and ARC
processes. Welding rod usage for these welding assignments included the
6010, 6011, 7018, MIG Flux Core Wire .035, ARC3L16 (S/S), and TIG Aluminum
4043.
David L. Carrasco Job Corps Campus Welding Instructor
El Paso, Texas
May 1994 - March 1997
As the lead welding instructor I conducted classroom and practical
application of welding processes and procedures. Instructional design
consisted of core curriculum instruction including but not limited to
Oxygen Acetylene, MIG, TIG, and ARC welding processes. Classroom objectives
consisted of student pass/fail on plate, pipe, and aluminum welding.
Students also complied with safety procedures and proper equipment usage.
El Paso Community College Welding Instructor
El Paso, Texas
July 1991 - May 1998
As the lead welding instructor at the Community College level, I
conducted introductory, mid-level, and advanced level welding instruction.
Instructional design consisted ob both classroom safety and equipment usage
instruction. All levels of Adult Learners complied and participated with
classroom objectives designed to expose the learners to Oxygen Acetylene,
MIG, TIG, and ARC welding processes. Students were required to pass
formative and summative assessments that required students to correctly
identify numerical sequence of penetrating and filler welding rods and
applicable usage of rods.
TEPCO Industries TIG Welder
El Paso, Texas
May 1982 - October 1991
Welded Cruise Missile aluminum castings in compliance with Department
of Defense directives, guidelines, and specifications. Aluminum castings
complied with 100% x-ray TIG weld inspections. In addition to Cruise
Missile castings, welded other castings as assigned including F-16 aircraft
parts and Harpoon Missile castings. Welding assignments required applicable
usage of the 4043, 5356, and 5254 welding rods.
Education
Bel Air High School
El Paso, Texas
High School Diploma
Graduated 1979
El Paso Trade School
El Paso, Texas
Certificate of Program Completion
200 Hours of Welding Instruction
Certifications
Combination Welder Certifications - available upon request.
Contact this candidate