Resume

Jesse Galaviz

**** ******** **. **** **

Fallbrook, Ca. 92028

Home Number 760-***-****

Cell Number 909-***-****

abny3h@r.postjobfree.com

Position: Inspector

AWS Certified Welding Inspector (CWI) AWS D1.1

AWS Code Endorsement API 1104

AWS Certified Welding Educator

ASNT ACCP Level II Visual Inspector

I.C.C. Inspector Sprayed applied Fire Proofing

I.C.C. Inspector Reinforced Concrete

I.C.C. Inspector Structural Steel Bolting (S1)

I.C.C. Inspector Structural Steel / Welding (S2)

I.C.C. Inspector Structural Steel / Welding (Legacy)

A.C.I. Concrete Technician

L.A. County (Steel/ Welding) Inspector

L.A. City Deputy (Steel/ Welding)

L.A. City Deputy (Drilled in Anchors)

L.A. City Deputy (Sprayed applied Fire Proofing)

L. A. City Deputy (Reinforced Concrete)

L.A. City Deputy ( Shot-crete)

Nondestructive Training:

College of Ocean engineering 10/13/08---2/25/09

Ultrasonic Testing U. T. Technician Level II

Magnetic Particle M. T. Technician Level II

Dye Penetrate testing P.T. Technician Level II

Clearance: Secret

Education: B.A. Cal State San Bernardino

A.S. Degree San Bernardino Valley College

3 years Ironworker apprenticeship Local 509

3 years Ironworker apprenticeship Local 433

U.S Army Ranger 75th

Experience:

Employment History

Navistar Defense Contractor 10/2012---Present

1675 East Whitcomb Ave

Madison Heights, MI 48071

Position CWI/NDT Inspector

Jalalabad Afghanistan (Location)

I conduct continuous visual inspection for the MRAP MSU vehicle up-grade for the U.S. ARMY

Operation enduring freedom (O.E.F.). I would perform Magnetic Particle inspection using

Magna-Flux Y-1 yoke. I would perform daily calibrations on equipment. I would monitor preheat

And inter-pass temperature and verify Volts and Amps to WPS. I would assist in resolving

solutions to problems and re- write new WPS to meet the codes compliance. I would

Certify new personnel (welders) to code standards due to high turn-over rate. This was because

the base would come under attack from incoming mortar and Rocket Propelled Grenade

creating

Stressful situations.

Nova Engineering and Environmental 5/2012 11/2012

4373 View-ridge Ave

Suite B

San Diego, Ca.

Position CWI/NDT Inspector

I conducted continuous visual inspection to the criteria of AWS D1.1. I provided surveillance for

shop inspection for the San Bernardino Court house project. I would also perform Ultrasonic

weld testing (UT inspection) on Cruciform columns, base plates, continuity plates.

West Coast Special Inspection (NDT) 3/2012---5/2012

4373 View-ridge Ave

Suite B

San Diego, Ca.

Position CWI/NDT Inspector

I conducted both visual and Ultrasonic shop inspection for Sharp Memorial Hospital (Retro-fit

San Diego, Ca.) I would inspect welds using visual criteria

from AWS D1.1 Structural Welding Code and AWS D1.8 Seismic Provisions. After the welds

had passed visual I would conduct Ultrasonic test (UT) Cover Plate assemblies for enclosing

existing Column structures to AWS D1.1 and AWS D1.8 code provisions.

PSI (NDT) 11/2011 2/2012

6032 North Cutter Ave

Suite 480

Portland, Oregon

Position CWI/NDT Inspector

Conducted visual and Ultrasonic Field inspection for Intel project Hillsboro Oregon. UT gravity

Column Splices, moment Frames and performed visual inspection to standards of AWS D1.1.

San Bernardino Valley College 8/96 to 12/2012

701 S. Mount Vernon Ave. 17 Years as a Welding Instructor

San Bernardino, Ca. 92410

Department Chair/CWI

I work as a welding instructor for 17 years instructing students on fundamentals of welding

process. This process consisted from Oxyacetylene (gas welding) to Shielded Metal Arc Welding

(SMAW), Gas Metal Arc Welding, (GMAW), Flux Cord Arc Welding (FCAW) and (TIG) Gas

Tungsten Arc Welding. I would write up Weld procedures and perform mechanical tests for

welder Certification for both AWS and Los Angeles department of building and safety. I would

also conduct Procedure Qualification Report (Procedure mechanical testing) for local companies

in the area.

Allied Inspection Service 2/2007 3/2008

1508 East 1st Street

Los Angeles, Ca.

CWI/ICC Special Inspector

Nondestructive NDT UT/MT

I was the resident and lead inspector in-charge of 5 other deputy on-site inspectors

on the Kenmore Towers. The project was an 18 story condominium fabricated from Structural

Steel. I would over-see and conduct final visual inspections on Welding, Bolting, Reinforce

Concrete and Fireproofing. I would write up Non-compliance reports (NCR’s) and work with the

general contractor on resolving issues. I would also conduct Ultrasonic angel beam (Shear) and

straight beam inspectors on welds. I would Ultrasonic test welded gravity Columns Splices and

special moment frames under AWS D1.8 seismic provisions. I also performed Magnetic Particle

inspection on the removal of weld run-off tabs and the removal of backing bar prior to the

completion of welding the bottom flange.

Herrick Corporation summer 5/2000 to 9/2000

5454 Industrial Pkwy

Devore, Ca.

CWI

I work as a Q.C. manager overseeing the Disney Concert Hall (Los Angeles, Ca.) and

conducting dimensional checks, visual inspection, and arranging for 3rd party inspection and

monitoring and resolving any issues or problems that occurred. The work had to meet both AWS

D1.1 Structural Welding code and AWS D1.8 Structural Seismic provisions (Fema 353).

Duncan Bros 8/94 to 8/96

1966 Date Street

Bloomington, Ca. 92377

Ironworker/ Welder

I worked as a Field Iron-worker/Welder; welding columns, beams, and miscellaneous iron using

SMAW and FCAW welding processes. I welded under Ultrasonic and Magnetic Particle

inspection which met to the standards of AWS D1.1.

Sullivan’s Welding 3/91 to 8/94

9421 Fernon Blvd.

Rancho Cucamonga, Ca. 91730

Field Ironworker/ Welder

I worked as a Union Pile-driver welding on multiple Metro-rail projects conducting such tasks as

welding on soldier piles, whalers, struts, and Complete Joint penetration groove welds using the

FCAW process (NR232 wire.). I was the lead welder and would perform visual inspection and

repair weld discontinuities. I work on most of the Metropolitan subways systems in the Los

Angeles down town area.

Rebar Engineering 8/88 to 2/91

10706 Painter Ave

Santa Fe Springs, Ca.

Field Ironworker/ Welder

I worked as a Reinforcing Steel Iron-worker/Welder. I would weld rebar direct bar to bar splices

and indirect bar to structural using SMAW process and FCAW process to both AWS D1.1

Structural Steel Code and AWS D1.4 Reinforcing Steel code. When I wasn’t welding I would

jump in and assist of the placing and assembling or rebar footing, slab, pour walls, and in place

parking structure. I worked on commercial projects ranging from Disney land parking structural

to Cal trans retro-fit projects.

Junior steel 1/86 to 8/88

660 S. Sixth Street

City of industry, Ca. 91746

Shop Ironworker/Welder

I worked as a Union Shop Iron-worker/Welder performing tasks as lay-out and fitting structural

members from a set of blue prints. Members would be Columns, Girders, and Beams.

Miscellaneous iron. I would perform Quality Control and inspect structural member for weld

discontinuities.

Lee & Daniels 2/84 to 12/85

500 Danlee Ave

Azusa, Ca. 91702

Shop Ironworker/Welder

I worked as a Union Shop Ironworker/Welder; welding Columns, Beams, and miscellaneous

iron using Flux Cord Arc Welding Process (FCAW) and Shielded Metal Arc Welding (SMAW) to

AWS D1.1. The company required welders to pass both visual and X-ray work by 3rd party

inspection companies.

Contact this candidate