Engineer Design

Timothy D. Sundermann

*** ** *** ******, *******, AR 72046 ? 501-***-**** ?

**************@***.***

Experience 2009 (Jan)-2009 (Dec) Falcon Jet Little Rock, Ar.

Systems Engineer

Model Installations for Aircraft System Components (Oxygen, air,

water, and waste)

Design and model installation of coffee and water, dispensing units

Design and model installation of food chiller systems

Design and model installation aircraft ovens systems

using CATIA V5 and Enovia

2006 (Dec)-2008 (Oct) Spectrum Aeronautical Spanish Fork, UT.

Interior Project Engineer, Design

Design and develop interior fuselage systems for graphite composite

filament wound aircraft

Generate 3D solid models, of interior elements and assemblies using

solidworks

Generate 2D production drawings using 3D solidworks models.

Systems consisted of cabin and cockpit restraint systems, seats,

floor boards, Instrument panel, windscreen and windshields,

bulkheads, lavatory, cabinets, PSU, baggage compartment, Acoustic

insulation, etc.

Write design objectives and requirements.

Produce trade studies

Hold PDR meetings for interior components, and review trade studies

Generate interface control documents and drawings for interior

components

Write certification compliance check list (CCL)

Produce tooling models and drawings for filament winding of Spectrum

40 Fuselage

Coordinate with R&D in the development of test equipment,

prototyping components, and performing functional test procedures

for FAA certification ( part 23)

2004(May)-2006 (Dec) Columbia Aircraft Bend, OR

Fuselage Project Engineer, Design

Design improvements of fuselage systems such as interiors,

landing-gear, 28 volt VCS air conditioning, oxygen, seats, control

systems, G-1000 instrument panel, etc.

Coordinate design efforts between the mold shop, M.E., R&D and shop

floor in the design phase to produce the best design for the lowest

cost (lean design) and design by experiments

Work closely with outside vendors, marketing, manufacturing and

purchasing, to develop and incorporate new and improved components

for existing product

Coordinate with R&D to develop test equipment, prototype components,

and perform functional test

Supervise other draftsmen

1999 (Aug)-2004 (May) Bombardier Aerospace Tucson, AZ

Interior Engineer

Design and Generate Detail, Assemble and Installation Drawings for

Aircraft Interior Components (Headliners, PSU's, Side Ledges,

Sidewalls, Dado Panels, Galleys, Wardrobe Cabinets, Entertainment

Cabinets, Lavatories, Bulkheads, seats, etc.)

Aircraft Lead: (Generate, Maintain and Monitor project progress

against schedules through aircraft Drawing Indexes)

Write Smoke Containment Reports (14 CFR part 25)

1996 (May)-1999 (Aug) Applied Aerodynamics Farmers Branch, TX

Liaison Engineer

Design and Coordinate Nonstandard Repair Approvals of Aircraft

Control Surfaces, Engine Cowls, Flap Panels, Fairings, Doors, and

Radomes with Company DER or OEM Engineering

Monitor, Analyze, Improve and Maintain Repair Processes (Clean Room,

Etch Line, Vapor Degreaser, Autoclave, Hot Bonding, Wet Lay-Ups,

Sheet Metal, Heat Treating, Vacuum Bagging, and Radome

Transmissivity Testing)

Research and Development for Production of Composite X-band Radome

(DuRaDome)

Find, Distribute, Track and File Repair Tech Data for Repair

Technicians (IPC, OHM, CMM, SRM, DWG's, etc.)

Programmed, Performed and Analyzed Destructive Test on Universal

Testing Machine. (Climbing-Drum, Metal-to-Metal Peel, Floating

Roller, and other ASTM test)

Backup and Maintain Network of 25 Workstations and Web Page

(www.aerodyn.com)

Computer Solid Works 2007 (3000 Mathcad Product Center

Skills hrs)

Auto Cad (9000 hrs) Matlab FORTRAN

Inventor 11(2000 hrs) DTS Catia V5 (1000 hrs)

Microsoft Office Motiva Enovia (1000 hrs)

Education University of Texas at Arlington B.S.A.E

Electives: Computer Aided Design, Dynamic Systems Modeling and

Linear Algebra

Senior Lab Project : Designed and Constructed Weight-and-Balance

Test Stand using Strain Gauges

Autonomous Aerial Vehicle Project: Constructed Rotor Test stand

and Performed Studies on Custom-Built Ducted Fan Assembly for the

UTA

Abaris Training "Composite Laminate Design" 1999

Private Pilot Certificate Obtained 1984

Contact this candidate