Maintenance Injection Molding
Resume:
Charles Luke McCurdy
Rittman, OH 44270
********@***.**.***
Objective
I have numerous abilities including electrical, mechanical, and supervisory
skills with extensive knowledge of machine operation and repair. I am a
reliable worker who is willing to work hard in respective positions. I am
seeking a full-time position with competitive benefits and wages. I
believe I would be an asset to your company.
Experience:
2000 - 2013 Sterilite Corporation, Massillon, OH
Assistant Maintenance Supervisor
Responsibilities:
Scheduled, followed through, and performed preventive maintenance.
Accountable for completing and assigning daily maintenance tasks.
Logged work performed on machines.
Kept inventory and ordered parts.
In charge of continuous training of maintenance mechanics for
troubleshooting machine problems and safety procedures.
Start up and shut down molding machines and start up after tool changes.
Performed processing to determine if there was a machine or tooling
problem.
Full knowledge of Van Dorn 500 HT, 770 HP, 1000 HP, 1500 HP presses with
Pathfinder 2500 and 3000 Controls.
Full knowledge of Van Dorn 770 HP with Electric Screw Drive System.
Full knowledge of Van Dorn Demag 950 Two Platen presses with NC4 Control.
Full knowledge of Cincinnati Milacron MM880 Maxima with XTREEM ST Contol.
Full knowledge of Impco 350 and 500 presses with relay logic control.
Troubleshoot and repair of electrical, hydraulic, and pneumatic systems.
Rebuilt or replaced injection molding machine components such as: AC (480
and 240 volt/3 phase motors).
Troubleshoot/rebuilt DC motors.
Replaced ram packings and advance cylinders on HP machines.
Changed over and rewired Hydrolux FC and GG1 valves.
Changed over and rewired 2500 to 3000 pathfinder controllers.
Tore down and rebuilt manifolds, PVH pumps, and cartridge valves.
Rebuilt manifolds, pumps, changed link pins and bushings on HT machines.
Changed tie bars, brass tie bar nuts, and adjusted to correct stretch.
Complete tear downs and rebuilds on all machines during yearly PMs.
Installed plastic molding machines.
Maintained and repaired chilled water and cooling tower systems.
Troubleshoot and repaired vacuum and blower pumps for material transport
systems.
Robotics: Installed Wittmann robots on molding machines, troubleshoot,
repaired and serviced robots.
1997 - 2000 J&O Plastics, Rittman, OH
Maintenance Supervisor and Mold Setter
Responsibilities:
Scheduled, followed through, and performed preventive maintenance.
Designed, engineered, and built robotics equipment, flow plates, stampers,
and launchers.
Installed, setup, maintained, and rebuilt Plastic Injection Molding Press.
Parts Expediter - inventory, ordered parts and supplies.
Exclusive maintenance employee in entire plant.
Supervisor in charge in absence of scheduled supervisor.
1995-1997 Contours Inc., Orrville, OH
Maintenance
Responsibilities:
Troubleshooting and repaired electrical and mechanical break downs, fork
lift, natural gas fired annealing furnace and HVAC.
Machine shop tasks on horizontal mill and lathe.
Inventory parts and restocked materials.
Maintained daily maintenance log for maintenance supervisor.
Accountable for completing and verifying projects daily.
Responsible for annealing furnace and cooling bell in absence of annealing
operators.
Worked closely with Plant Engineer installing new equipment, redesigning,
and rebuilding old equipment.
Trained and supervised new employees.
Transported machines to new facility.
Accountable for start up and shut down of plant.
Training classes required by company included Data Entry, Basic Shop Math,
Fork Lift Certification, and Safety Training for hydrogen and nitrogen
tanks in the Annealing Department.
While employed at Contours Inc., I was a member of the Problem Solving
Team, and a member of the Projects Team for disassembling, transporting,
refurbishing, and reinstalling the following work centers: Exact Length
Work Center, P-3, Single Stand Mills, Straight and Cut, Drawers, Cranes,
Draw Bench, and Quality Assurance.
1994-1995 Yankee Run Auto, Masury, OH
Proprietor of auto mechanic shop
1984 - 1993 Houston Steel, Houston, TX
Maintenance Supervisor
Responsibilities:
Scheduled and followed through with duties on time.
Preventive maintenance.
Installed new equipment.
Parts expediter, outside contractor pricing, and kept a running inventory
of available parts.
Blue print reading.
Machine shop work.
Troubleshoot and repaired equipment throughout facility, including fork
lift and HVAC.
1976 - 1984 D&N Transport, Cortland, OH
Electrical Maintenance Team Leader and Technician
Responsibilities:
Machine shop work.
Crane mechanic.
Rebuilt hydraulic cylinders.
Troubleshoot and repaired pumps, motors, gear boxes, fork lift, and HVAC.
Heavy equipment mechanic.
Education
1996 Wayne County Schools Career Center, Smithville, OH
Advanced Electronics
1976 - 1979 Brookfield High School, Brookfield, OH
Major: Industrial Arts
References
Available upon request.
Contact this candidate