Maintenance Technician

Nguyen L Dang

***** ****** **.

BALDWIN PARK,CA *1706

Cell: 626-***-****

E-

mail ********@*****.***

Sumary

A&P license Mechanic with extensive aviation knowledge, Inspection and

maintenance experience from General aviation reciprocation engine

aircraft to Mid /large sized corporate A/C "Gulfstream, Cessna

Citations" to inclusive of airliners 747, 737, DC10. Maintenance

performed as progressive phase, "C" checks, 72months, 5000 landings,

annual inspection tear down repair, overhauled, replaced. Reassembles

and installed with ops, leaks and functional checks. Technician is

experience with troubleshoot and maintenance on all aircraft systems

such as hydraulics, pneumatics, fuel, engines and controls, flight

controls, landing gears, autopilot, pressurization, air conditioning,

battery, electrical wiring systems and general avionics accessories

repair and replaced, Performed annual system pitot/static leak checks

verification buyoff, list among others. Technician is highly skill

with all types of heavy structures as far as analyze, remove, repair,

modified, reinstall and replace in reference to structural repair

manual, technical datas, blueprints and engineering reference orders.

Corrossion treatment and repairs, parts fabrication with conform

material ID. Familiar with all types of fasteners, special fasteners

installations and usages. Technician is knowledgeable with inspection

awareness which results to excellent standards of quality. Engine run

and taxi qualified on Citation aircrafts. Candidate is well

trained/certificated to serve as a mentor to fellow technicians on

effective maintenance and work documenting. Proof of certification is

available upon request.

Work Experience

Triumph Aerostructures, Hawthorne, Ca

10/2010- Present

747/767 Structural Production Mechanic

Responsibility,

Performed fuselage structural final assembly and repairs. Coordinated

for proper work planning, verified required parts to assemblies per

blue prints and all approved data requirements. Locate, drill and

fabricate parts to final finish. Work with close tolerance fittings

and fastener holes per specs call out. Prepare for final assembly

with approved manufacturing process and material finish per data.

Assembled parts and fasteners to final specs. Coordinated with

supervisor and planers for final assemblies defects in needs of repair

. Consult directly with inspections and engineering for repair

dispositions and repair procedures. Removed and or repairs damaged

part as needed per engineering requirements. Verified required parts

to assemblies with repair holes location, locate and drill parts to

new final finish. Pull and repair damaged holes as needed. Assembled

parts and fasteners including oversized to final specs with close

finished tolerance.

Work primary consist of manufacturing support for repair damages with

engineers, reworks to finish with on time schedule delivery. Serve as

training and mentors new and junior technicians to assure precise

manufacturing production process including proper tools usage and

applications.

Work often consist of manufacturing support for repairs in associate

to damages with engineers, reworks to finish with on time schedule

delivery.

Evergreen Maintenance Center. Tucson, AZ

05/2010 - 11/2010

A&P Technician

Responsibility:

Performed line maintenance on Boeing 747 aircrafts. Work consist of

component replacements, lubrications and systems services, aircraft

electrical interior and exterior lighting replacements, interior removal

and reinstall, flight control services and overhaul, performed all minor

and major structural repairs such as seat track assembly, damaged and

corroded web and floor beam, "T" cap removal, fabricated, located and

reassembled. Cowling damaged repairs by ways of sections removal,

fabricated new parts and reassembled. Corrosion treatments and skin

repairs. Cargo rollers and floor panels repairs.

Cessna Citations. Long Beach. Ca

10/2002 - 03/2009

Inspector.

Responsibility: Performed all required Phases of inspections on all

Citation Jets. Work inclusive of aircraft log entries and researches,

RII maintenance buy offs, inspections, audits and return aircraft to

service.

Responsible for all Quality Control inspection of aircraft/components

in repair station.

Complete inspections of aircraft airframe, engine, and components

relates to overhaul, replace and repairs to ensure conformity to

manufactures and FAA approved/acceptable data.

Coordinates mechanical, electrical and inspection requirements on the

aircraft during maintenance or outfitting and keeps accurate, neat and

legible records of the work performed.

Coordinates throughout assigned jobs with RTS to ensure accurate

aircraft records are produced in a timely manner.

Conduct audits of maintenance documentation for accuracy and

completion on all aircraft prior to approval for return to service.

Ensures aircraft/component are airworthy prior to any flight

activities.

Engine post maintenance power run and performance acceptance buyoff

qualified. Engine run authorized examiner.

Responsible for all inspection incoming recieves for proper

acceptance and documentations.

Mentors technicians on effective work documentation as to ensure

components 8130/ approved RTS datas are properly kept and recorded.

Assure customers flight manuals temporary revisions are incorporated

and up to date.

Continually monitors repair station compliance with FAR 145 and the

FAA accepted site repair station and quality control manual. Inclusive

of all maintenance/components/repair manuals are revised and up to

date. All tools and calibrated equipments are up to date.

Communicates with management as require to identify work assignments

and delivery schedules.

Cessna Citation, Long Beach. Ca.

08/2001 - 10/2002

Aircraft maintenance lead technician

Responsibility: Complied with Phase inspections. Inspect, repair and

overhaul all systems on all Citation Jets. Performed task ops and

functional checks to verified system validation.

Troubleshoots aircraft malfunction in-conjunction with pilot

discrepancy and problems reports reference to indications from

aircraft onboard diagnose computer and ICAS. Electrical Systems

associate to sensor malfunction remove and replace which involves with

anti-icing, cabin temp. control, winshield heater. Pressurization and

pneumatic distribution work with troubleshooting to airpack

replacement. Air-conditioning services, along with compressor

replacement, system purge and freon service. Engine works involving

remove and reinstall due to Hot section and time schedule required,

component replacement, services to filters, ignitors, oil and fuel

chip detect, pressure and impending sensor checks. Engine post 5 point

run for ops, leak and functional checks. Flight controls works with

cable replacement, hydraulic actuator replacements, complete system

final rigging along with functional checks.

Performed major sheet metal FOD damaged projects such as wing leading

edge/ skin, fuselage skin, major frame structural damaged assembly and

fuel cell damage repairs to complete hard landing structural overhaul.

Such works requires precise layouts with close tolerance fastener hole

drillings and fittings to reassembled. Stab and leading edge anti-ice

replacement, windshield assembly replacements, seat track

replacements, nose section repairs inclusive of radome damaged

replacements by way of locating new radome, trim to fit, drilled with

precise locations and tolerance, reassembled per blue prints and

technical datas. Complied with all major SB's and AD's. Researched and

consult directly with engineering to solve complex technical and

repair issues.

Gulfstream Aerospace Corporation, Long Beach, Ca.

07/1998 - 04/2001

Aircraft Maintenance, Senior Technician.

Responsibility: Serviced, maintained and performed overhaul,

modifications and repairs on all Gulfstreams Corporate Jets.

Accomplishments:

Provided extensive aircraft incoming services for 72 months, 5000

landings. Overhaul and repairs as needed which involves in removals of

engines, flaps, landing gears, flight controls and associated

components along with trouble shooting, follow up with riggings,

functional checks, final services.

Performed various types of structural repairs inclusive of heavy sheet

metal repairs and composites.

Achieved all aircraft maintenance and responsibilities with high

quality standards in timely manners.

Completed complex alterations, repairs and consulted directly with

corporate clients to provide technical advice, resulting in increase

in customer satisfactions and comments.

Supervised and trained colleagues on special projects and assignments.

Cherry Aviation, Long Beach, Ca

02/1996 - 05/1998

Aircraft Maintenance Technician.

Responsibilities: Provided 100hr/annual inspection, maintenance,

services, overhaul and repairs on General Aviation Aircraft. Work

involves structural repairs, replaces, and rebuilt aircraft

structures, such as wings and fuselage, flight controls including

rigging. Inspected engine for defects, operate engine to detect and

diagnose malfunction, troubleshoot for electrical/mechanical failure.

Problems resulting to replacing or repairing worn or damaged

components, engine and airframe accessories. Final engine run and

adjust to fuel controls, carburetors, magnetos, voltage regulators.

Assure all systems functional, documented and return aircraft to

service.

Heli-Orient, Singapore

1990-1995

Aircraft Maintenance Technician.

Responsibilities: Provided helicopter maintenance services and

structural repairs on Bell Helicopters.

Continental Airlines, Los Angeles, Ca

1987-

1988

Aircraft Maintenance Technician.

Responsibilities: Provided heavy maintenance, services and structural

repairs on 737, DC-10 "C" checks, "B" checks.

Educations

Northrop University, Inglewood, Ca. Airframe and Powerplant.

Licenses: Airframe and Powerplant,

Private Pilot

Certifications :

* Continental Airlines DC-10 Aircraft maintenance

* Aircraft Structural Repairs (Singapore)

* Gulfstream Aircrafts: GII, GIII, GIV, and GV Systems.

* GV Hydraulics, GV Pneumatics, GV Avionics, GV Electrical systems

* GIV Electrical systems

* Rolls Royce Spey 511-8 Engine

* Rolls Royce Tay 611-8 Engine

* BMW-Rolls Royce BR-710 Engine

* RE220 APU,

* Permaswage Swage & Fittings

* Composites

* Human Factors

* Citation 500 series

* Citation 680 Sovereign

* Citation 560XL

* Citation 750(X)

* Cessna N.D.T. task certify on magnetic particle and eddy current.

Additional skills: Working Knowledge of Microsoft office.

Contact this candidate