Engineer Training
Resume:
Name : MAHADI PM CAPAH
Email : *******@*****.***
Phone number : +628**********)
Address : Batam, Indonesia
Education : Polytechnic University of North Sumatra 1998 Majoring Mechanical Engineer
Kepulauan Riau University Batam, 2002 Majoring Industrial Engineer
Passport No : P995606
Expected Salary : Negotiable
Notice Period : 1 Month
Family Status : Married,
Current Location : Batam - Indonesia
Key Point :
• Instructor for Dogging Operation and Basic Rigging: Plan Work - Crane type and capacity requirements; site rules and contacts; hazard identification; priorities; emergency procedures. Lifting gear selection, load calculation.
Rigging Equipment Inspection: - Perform 6 month inspection for all lifting gear, prepare for document, procedure, check list.
Rigging Audit : Perform rigging audit to selected client, audit focus to the system, repair and maintenance.
• Instructor for other HIGH RISK License training
o Basic Scaffolding and Intermediate/Advance Scaffolding
o Forklift operation Relevant UEPOPS228A – Conduct Forklift Operations
o Working At Height Relevant MNMG237A – Working Safely at Heights
o Confined Space Entry Relevant MSAPMPER205C
• Certified for TAE IV for Training and Assessment Level IV from Australia
• Certification :
No. Certification No. Training Provider
1 Basic Rigging CA62825 AUSTRALIAN SKILLS TRAINING
2 Advance Rigging for Supervisor CA62824 AUSTRALIAN SKILLS TRAINING
3 Basic Scaffolding CA62827 AUSTRALIAN SKILLS TRAINING
4 Rigging Equipment Inspection CA73132 AUSTRALIAN SKILLS TRAINING
5 Intermediate Scaffolding CA62828 AUSTRALIAN SKILLS TRAINING
6 Overhead Crane CA73131 AUSTRALIAN SKILLS TRAINING
7 License to Perform DOGGING CA69354 AUSTRALIAN SKILLS TRAINING
8 Work Safely at Height CA62826 AUSTRALIAN SKILLS TRAINING
9 BOSIET by M&O Indonesia
(Approved by OPITO) 93925707280511001 MARINE AND OFFSHORE INDONESIA
10 Forklift Operation CA 64325 AUSTRALIAN SKILLS TRAINING
11 Welding Inspector IKBAL M YOS Batam 432/WI-XVII/III/2009 IKBAL M YOS BATAM
12 Boiler Operator 1st Class 203/PNK3/-PUBT/B-I/II/10 MINISTRY OF MANPOWER AND TRANSMIGRATION(INDONESIA)
13 OPEN WATER DIVING 1105AZ7063 PADI
14 EMERGENCY FIRST RESPONSE 1106AQ2712 PADI
15 Emergency First Response Instructor EFR-306666 PADI
16 Training and Assessment(TAE CERT IV) CA69778 Australian Skills Training PTY LTD
17 CONFINED SPACE ENTRY CA67123 Australian Skills Training
Specialized Training :
A. Quality Management system
No Training Detail Duration Provider
1 ISO 9001-2000 Internal Auditor Aug 2006 AJA Singapore
2 ISO 14001-2000 Internal Auditor Aug 2006 AJA Singapore
3 AS 9001 Aerospace Internal Auditor 2008 EATON
B. Communication/Motivation
No Training Detail Duration Provider
1 Understand Japanese Culture June 2000 Asia Matsushita Singapore
2 Human Behavior in Organization Sept 2002 TEAC Training Center
3 Bi-Partite Training Dec 2003 Sumber Daya Dian Mandiri
4 Ethic At Work: Doing the right thing Feb 2008 EATON University
C. Special Training
No Training Detail Duration Provider
1 SPC Training 2008 EATON University
2 1st Class of Boiler Operator Feb 2010 DepnakerTrans
PROFESSIONAL EXPERIENCES
May 1999-Mar 2002 PT. Quantum Corporation-Matsushita Kotobuki
Muka Kuning Batam Indonesia
Process Engineer
Sept 2002 – Sept 2005 PT. TEAC Electronics Indonesia
Muka Kuning Batam Indonesia
QUALITY ENGINER – INCOMING QA SUPERVISOR
Oct 2005 – Feb 2008 PT. PANASONIC SHIKOKU ELECTRONICS INDONESIA
Muka Kuning Batam Indonesia
Position: Quality Engineer. [Hard Disk Drive
Assembly, EMS, and Linear Tape Open]
Feb 2008 – Feb 2010 PT. Fluid Science Batam-EATON Aerospace
Muka Kuning Batam Indonesia
Position: Quality Engineer.
Feb 2010 – Feb 2011 Mitra Energi Batam subsidiary of MEDCO Energi International – Power
division
Position: Control Room Operator and Combine Cycle Technician
1. Water tube Boiler (35T/hr) Natural gas fired Start up, Shut down, Normal & Emergency operation., commissioning
2. Turbine Start up, Shut down, Normal & Emergency operation.
3. Generator operation.
4. Operation and Maintenance of Auxiliaries like Boiler feed pumps, CW pumps, Condensate pumps, Air compressors, motor, etc.
5. P&ID drawing interpretation to monitor the entire instrument and control valve.
6. Combine Cycle EPC Project especially at Installation.
Current Job Feb 2011 – Now
Australian Skills Training
Jobs and Responsibility:
• Rigging Instructor (Basic and Intermediate/Advance) Australian Skills Training -Australian Standard, Steel erection, Winches, fleet angles, Lifting purchases, sheaves & calculation of loads, Calculation of counterweight required for cantilever beams, General rigging appliances & fittings, Packing, securing & moving loads, Rope knots & splicing
• Rigging Equipment Inspection: - Perform 6 month inspection for all lifting gear, prepare for document, procedure, check list.
• Rigging Audit : Perform rigging audit to selected client, audit focus to the system, repair and maintenance.
• Instructor for other HIGH RISK License training
o Basic Scaffolding and Intermediate/Advance Scaffolding
o Forklift operation Relevant UEPOPS228A – Conduct Forklift Operations
o Working At Height Relevant MNMG237A – Working Safely at Heights
o Confined Space Entry Relevant MSAPMPER205C
Skills
Communications Skills (listening, verbal, written).
Analytical/Research Skills.
Computer/Technical Literacy: MS Word, MS Excel, MS Office, MS Power Point, e-mail
Flexibility/Adaptability/Managing Multiple Priorities.
Interpersonal Abilities.
Leadership/Management Skills.
Multicultural Sensitivity/Awareness.
Planning/Organizing.
Problem-Solving/Reasoning/Creativity.
Teamwork.
Able to calculate cost of non-conformance/Cost of Quality
Your Faithfully,
Mahadi PM Capah
Contact this candidate