Industrial Process Solutions
Service Technician Ivy land PA
Receive daily assignments from service manager. Go to customer sites and work on
Customer air dryers.
Perform either repairs or preventive maintenance on the air dryer systems, which included
Changing of desiccant, replacing air filters to the pre-filters and after filters, rebuilding the
Inlet and Purge outlet valves along with the purge inlet and outlet valves and
Purge adjustment check valves.
Troubleshooting PLC and relay logic, Brands such Allen Bradley Roxwell RSLogix 5000. Siemens S7 and others. As well as trouble shot Logix5000 Controllers I/O. Using HMI’s Roxwell automation to operate
troubleshot, adjusted programs and calibrate VFD’s drives such as Allen Bradley PowerFlex 70, Emerson Siemens Toshiba and Westinghouse. Voltages from 115v to 230v 460v. Calibrated different digital valve controllers.
Reading P&IDs, Electrical, Pneumatics and Hydraulic Schematics and prints.
Instrumentation sets ups and calibrations. Calibrated control pump and control valves 4 t0 20mA Loop pressures /flows
By using lap tops and control panels diagnose and making command changes. Repair Electrical systems.
Repair or upgrade Mech, ADC controllers and swing arms.
Repair and PMS on competitors’ air dryer and go over air compressor upstream of air dyer
Fill out reports on service done to customer equipment and recommend service that needs to
be done next.
Observe other customer equipment that could be worked. See if customer needs new
Parts, dryers and possible other service opportunities and possible upgrades on equipment.
Travel far sites. Working in the city and over nights stays.
Report back to service manager and keeping salesmen informed.
8/2010 to present
American Crane & Equipment Corp. Douglassville PA,
Service Technician 02/08 to 10/09
Go to customer’s sites and perform repairs and upgrades.
Install new equipment and de install old equipment.
Inspect Indoor Cranes and equipment to OSHA requirements. Work was performed at power plants, nuclear power plants and various industrial companies.
Write up reports for customers to bring the customer up to OSHA Standards.
Perform preventive maintenance checks. Looking at the cranes brakes, Contactors, relays and motors. Inspecting wire rope and chains as well as the hooks. Replacing wire rope and chains
Troubleshooting PLC and relay logic, Brands such Allen Bradley Roxwell SLC 500, Siemens 200,300 &500 and dealing with Profibus-Dp and Profibnet troubleshooting making upgrades and making command changes to the prongs.
Electrical systems. Programmed equipment and fixing gears, bearings, belts and pulleys.
Dealing with high voltages such as V560, V480, V277, V240, V220 and V120.Troubleshot step down transformers
And transformers. Worked on step motors and VFD drives as such as Allen Bradley Emerson Siemens Toshiba and Westinghouse. Calibrated control pump and control valves 4 t0 20mA Loops pressures/flows Worked on step down motors.
Working on equipment while I troubleshot equipment that had Hydraulics and Pneumatics problems. I worked on
Injection Molding machines such Brands as Boy Machine, Husky, Hettinga, HPM, and Mitsubishi. Worked on Horizontal and vertical machines. Worked on clamps, pistons, HMI’s, Limit and safety switches, pumps, tanks, nozzles plasticizing barrels, decompression before Plasticizing screws rotations, advancing and retract, adjusting Pressure limits and delay time, clamping force and mold opening and closing problems and clamp pressure, application time.
Calibrating and upgrading software. Along with PMs.
Talk with costumers about getting upgrades on existing equipment or buying new equipment.
Kern International Oaks, PA
Service Technician 11/05 to 12/07
Maintain high-speed inserters for PSC Info Group and mail processing companies.
Perform service calls on k3000 and k46 un-winders and folders. Assemble rebuilds.
Troubleshoot electrical and mechanical problems, soldered as needed. PLC and fiber optic
Troubleshooting involved down loading software. Troubleshot step down motors and stepper motors Power supplies,
Frequency converters fiber optic cables, sensors and One, Two and Three phase motors.
Responsible for ordering and receiving parts utilizing Access based program. Write-off
RMA‘s and forward them back. Perform Inventory counts three times a year.
Organize tasks and goals for other technicians. Performed bi-monthly along with weekly reports. Send out daily
Perform routine monthly preventive maintenances checks and create monthly calendar for PMs. Work with the travel to different sites for training.
Peak Beam Systems, Inc. Edgemont, PA
Electronic Technician 06/00 to 10/05
•Assembled and tested 4200 searchlights and 4200 and 5200 chargers
•Troubleshooting down to component level using multi-meters and oscilloscopes
•Calibrated searchlight boards and chargers using test fixers and software programs
•Tested batteries and battery packs
•Responded to customer telephone calls by troubleshooting while on telephone
•I performed RMA repairs for customers and provided quotes for those repairs
•Assisted engineer with special projects pertaining to light boards and battery packs
•Involved with research and development of new products
•Soldered PC boards- thru-hole and surface mount
Acusort Inc (Contract Assignment)
Electronic Technician 03/95 to 03/00
Worked in functional test department.
Troubleshot down to component level
Used Oscilloscopes, spectrum analyzers, multi-meters, test fixtures.
Soldiered surface mount and through hole was certified mil spec. Worked also with, ISO 2000, 9001.
Standards troubleshot and soldiered using a Microscope.
Pennsylvania Institute of Technology Media, PA
Associate Degree in Electronic Engineering Technology
Courses included: Auto Cad Version 12, Basic Programming, Fiber Optics, AC-DC, Motors and Generators, / Troubleshooting. Delaware County Community College Media, PA Course in Microsoft Office (Word, Excel, Access, PowerPoint) 2002