acxayr@r.postjobfree.com

Michael Dell Sanders

Michael Dell Sanders

*** ***** ****

Albany, GA 31705 US

Mobile: 229-***-****

Day Phone: 229-***-****

Email: acxayr@r.postjobfree.com

Objective

My goal is to obtain a job as a mechanic doing what I enjoy and what I am good at.

Experience

11/2008-Present

URS Contractor (Marine Corps Logistics Base) Albany, Ga.

Mechanic

I disassemble, make repairs apply modifications, assemble and perform other similar duties in the repair of a

variety of heavy mobile equipment such as bulldozers, cranes, HMMWV, Landing Assault Vehicles (LAV),

AAV, tractors, and trucks. I use a variety of hand tools and power tools such as pneumatic impact wrenches

and drills to affect disassembly and assembly of equipment, repairs, adjustments and modifications in

accordance with established procedures.

I inspect parts for wear against set specifications; reclaims used parts for reuse or replaces with new parts,

rework brakes, chassis components, axles, wheels, and drive shafts. I install major components and effects

interconnections of control lines, cables, and wiring. I perform tune-ups, adjustment of linkage, timing and

servicing of equipment. I work independently using a variety of common test and measuring instruments

such as timing lights, dwell meters, feeler gauges, compressions test gauges, test lights, multi-meters in

adjusting, tuning, trouble shooting and repairing equipment.

Remove rust by use of portable electric and pneumatic sanders, impact tools, sanding by hand, scraping with

hand scrapers and chemical application. I remove contaminants such as road dirt, mud and grease by steam

cleaning and approved solvents. I preserve unit after process by changing fluids, applying tape, strippable

coatings, oils, grease, preservative compounds and paint surfaces after cleaning process by spraying,

brushing, wiping, fogging, and dipping.

I perform depot level maintenance on heavy mobile equipment. I inspect, disassemble, repair, rebuild,

modify, test and adjust engine accessories and various components such as: hydraulic, cooling,

electrical and mechanical systems, fuel tanks, drive shafts, vent ducts, and more to the exact

specifications as stated in the technical manual.

I utilized special tools and machinery such as impact wrenches, special pullers, arbor presses, blast

cleaner, drills, pressure gauges, micrometers and more to remove components for inspection to

determine if the extent of wear is within the acceptable tolerances for reuse or properly discard those

worn beyond limitation. I utilized a systematic approach to diagnose the problem, and independent

judgment to determine the degree of disassembly required in order to maintain the minimum expense

while maintaining or exceeding the standard of quality.

2/2006-11/2008

Defense Services Support (DS2) MCLB Albany, Ga.

acxayr@r.postjobfree.com

Michael Dell Sanders

Mechanic

In this position, my duties include disassembling, assembling, fabricating, modifying, and rebuilding, and

inspecting component parts for the combat vehicles such as AAV's, and LAV's. I determined repairs

necessary to return vehicle to proper operating condition, in a timely manner.

I diagnose, repair, overhaul and modify heavy mobile equipment, systems and vehicles with a through

working knowledge of the mechanical make up, operation, and working relationships of heavy duty systems,

assemblies, and parts (also major systems such as diesel and gasoline engines, automatic and manual

transmissions and gear reduction systems and accessories. I have electronic, electrical, hydraulic and

pneumatic knowledge of the systems of the vehicles that I work. I use hydraulic lifters, loaders, turners and

positioning systems along with the controls for each. I trace and locate defects involving hydraulic and other

major system failures. I determine the extent of repairs necessary by visual, auditory examinations and the

use of a variety of test equipment available. I have skill using measuring devices for fitting and installing

components such as pistons, valves, bearings, gears, cylinders, etc. to specified clearances. I use

independent judgment and make decisions within the framework of accepted trade practices and oral/ written

instructions by the supervisor. Vehicles records along I decide the work methods and tools to use for various

assignments. I work with minimal supervisory and / or leader assistance during and upon completion of my

assignments. During the performance of my duties, I use various tools and equipment such as; drills (electric

or pneumatic), pulleys, wrenches, torque wrenches, etc.

To perform duties, I work from oral instruction, blueprints, sketches schematics, engineering instructions,

work instructions, statement of work, and technical directives/manuals. I wear the required and proper

personal protective equipment (PPE) at all times during the work shift. I maintain a safe and clean work area.

I kneel, bend, stoop and perform duties in awkward positions; I am able to push, lift, or carry heavy tools

equipment for a reasonable amount of time.

I operate a wide variety of heavy mobile equipment to determine what repairs adjustments and

modifications are required. I operate MHE as required and perform preventive maintenance on

equipment.

I perform depot level maintenance at a journeymans level on heavy mobile equipment. I inspect,

disassemble, repair, rebuild, modify, test and adjust engine accessories and various components such

as: hydraulic, cooling, electrical and mechanical systems, fuel tanks, drive shafts, vent ducts, and more

to the exact specifications as stated in the technical manual.

11/2004-8/2005

Equity Group Camilla,Ga.

Maintenance Mechanic

Constructed, erected, installed and repaired wire belt and motors on production line.

Studied blueprints, sketches and building plans for information pertaining to type of material required.

Assembled, installed and repaired pipes, fittings and fixtures of heating, water and drainage systems.

Studied building plans and working drawings to determine work aids required and sequence of installations.

Inspected structure for obstructions to be avoided to prevent weakening of structure after installation of pipe.

Located and marked position of pipe and pipe connections and passage holes for pipes in walls and floors.

Planned layout, installed and repaired wiring, electrical fixtures, apparatuses and control equipment. Planned

new and modified installations to minimize waste of materials, provide access for future maintenance and

avoid unsightly, hazardous and unreliable wiring, consistent with specifications and local electrical codes.

Prepared sketches showing location of wiring and equipment, and followed diagrams and blueprints,

ensuring that concealed wiring was installed before completion of future walls, ceilings and flooring.

Job Related Training

Hand Tool Safety on Industrial Maintenance, 02/2010;

Asbestos Awareness Training Lead Based Paint Awareness Training Hazardous Waste Awareness Training

(40 CFR 265.16), 01/2010;

AT Level 1 Awareness Training, 12/2009;

acxayr@r.postjobfree.com

Michael Dell Sanders

USMC Annual Security Training Counter-Espionage Awareness, 12/2009;

USMC Annual Security Training Anti-Terrorism and Force Protection, 12/2009,

USMC Annual Security Training Basic Information and Personnel Security, 12/2009;

DOD Information Assurance Awareness, 3/2009,

Personally Identifiable Information Version 1.0, 3/2009,

Personally Identifiable Information Version 1.0, 10/2009; Personally Identifiable Information Version 8.0,

10/2009

Education

Mitchell Baker High School Camilla, Ga. Some high school coursework completed.

References

Name Employer Phone

Oscar Jackson Proctor & Gamble 229-***-****

Nolen Newberry MCLB Albany 229-***-****

Katie Haynes Mitchell County Board of 229-***-****

Education

Contact this candidate