SUMMARY

Over ** years’ experience in oil and gas industry

Piping engineer with extensive exposure to all aspects of hydrocarbon piping and plant design and construction

Sufficient practical field experience & communication skills relating to piping engineering

Experienced in both analytical and hand calculation, computer soft wares such as Caesar II, FE Pipe, Nozzle Pro, AutoPipe

Proficient in the use of relevant Engineering codes such as ASME Codes (B31.1,B31.3, B31.4, B31.8), ASME pressure vessel Codes (Section VIII, Div. 1, 2), WRC 107&297 and CSA Z662 for pipeline design

Engage in all phase of project (FEED, Detail design, spool fabrication, Construction and pre-commissioning)

Ability to work with internal teams, client personnel, other consulting firms

Coordinate the activities of the engineering and design groups assigned from mid to large sized projects.

EXPERIENCE

2011 - Present

Lead Piping Engineer, Saipem Canada, Calgary

CNRL Hydrotreater Phase 2B and Phase3 -Engineering, Procurement and Construction Project

Review the ITB (Invitation to Bid) documents submitted in the proposals stage, Issue inquiry requisitions, and review techno-commercial vendor offers

Prepare Piping Material Specifications (PMS), engage in the P&ID development, Plot plans, General Arrangement (GA) drawings,

Review Philosophies, Area Classification Drawings, Fire and Gas Detector Layout Drawings and other relevant documents for executing of Fire water underground, Closed hydrocarbon Drain & Process contaminated Sewer System.

Verify scope of work, budgeted man hours, total of deliverables

Monitor and control project Man-hour requirements during project execution

Establish target completion dates, and ensure target dates are achieved.

Prepare/check specifications/datasheets for pipes and fittings-valves, bends, tees etc. and technical evaluation of the vendors quote for completeness.

Site/Yard Construction support

Participate in 30%, 60% and 90% model review with client

Wall thickness calculation and Line list preparation

Prepares and issues specifications, data sheets, and other construction documents. Prepare/manage detailed purchase requisitions for piping components. Knowledge of shop and field fabrication techniques (Modularization) .

Reviews vendor data submittals to ensure compliance to design requirements,.

Provides technical guidance to CAD Designer/Drafters, Designers, and lower-level Engineers working on the same project.

Preparation of Piping Specialty item Datasheet, Specification / Selection, Technical Bid Evaluation & Vendor Document Review for piping components with overall knowledge of rotating equipment, material handling, HVAC equipment / packages and Piping as required.

Participate/Support detailed Engineering and perform check and stamping of Piping engineering drawings and stress calculations for piperack and equipment module

2008 - 2011

Senior Piping Engineer/Lead Stress Engineer, WorleyParsons, Calgary

Devon Jackfish 2 &3 SAGD Project

Participate/Support detailed Engineering and perform check and stamping of Piping engineering drawings and stress calculations for six SAGD well pads and pipeline between wellpad and Tie-in.

Prepare/check specifications/datasheets for pipes and fittings-valves, bends, tees etc. and technical evaluation of the vendors quote for completeness.

Develop a standard template for SAGD well pair module design to be used for all future Wolf Lake SAGD wellpads

Participate/Support detailed Engineering and perform checks of Piping engineering drawings and calculations of upstream piping for oil and gas production and CPF of the SAGD facilities.

Review Equipment Layouts based on tentative Equipment dimensions and arrange for issue of RFQs for ordering of Piping Bulk at Preliminary, Intermediate and final stages.

Stress analysis of piping connected to static equipment such as Vessel, Exchanger, Tank and rotary equipment such as Pumps and stress analyzing of the buried piping

Checking Loads on the Stress Equipment Nozzles, Local stress check on support, flange leak check, checking the PSV reaction force and sludge force on the piping system.

Preparing Datasheets for springs pipe supports, Expansion Joint and Struts.

Evaluating allowable loads on equipment nozzles using Nozzle-Pro

StatoilHydro Leismer SAGD Project

Preparing and checking of detailed piping stress analysis reports

Preparing the Specification for the Allowable Nozzle Loads.

Preparing the Stress Analysis Design Basis and Stress Critical Line list

Stress Analysis of the Critical systems for the various units in the plant.

Submitting Stress Analysis Reports to the Client and getting their approval

Complete manual/computer drawings and isometrics.

Check, back check, and correct manual/computer drawings and isometrics.

Checking Loads on the Stress Equipment Nozzles, Local stress check on support, flange leak check, checking the PSV reaction force and sludge force on the piping

Preparing Datasheets for springs pipe supports, Expansion Joint and Struts.

Checking stress runs and checking isometrics and GA for issuing IFC packages.

2006 - 2008

Senior Piping/Mechanical Engineer, Vantage Engineering, Calgary

Petro-Canada Mackay River SAGD Project.-Piping/Mechanical Engineer

Preparing the Specification for the Allowable Nozzle Loads.

Preparing the Stress Analysis Design Basis and Stress Critical Line list

Responsible for preparing as built, mechanical and piping design drawings and working on a variety of the project to deliver design drawings within the project time schedule.

Pipe stress analysis for above ground and underground piping.

Prepare Report for Lead Piping/Mechanical Engineer;

Bid Evaluation for the piping components and preparing the PO for all piping, valves, specialty items, control valves, filters etc. Maintain documentation and files for the projects

Perform visual, manual, and computer analysis of piping systems.

TransCanada Pipeline Meter Stations Project-Piping Engineer

Coordinate for preparation of installation and erection schedule and provide support to Procurement / Execution.

Coordinate for carrying our design checks for Fabricated and Packaged Equipments, overall dimensions, nozzle orientations, etc.

Cooperation with Regulatory department in order to receive all necessary permits

Project scheduling and progress report preparation for client

Reviewing the actual performance against the plan and making adjustments to maintain project direction and timing

1995 - 2005

Mechanical/Piping Engineer, TAM Engineering, Tehran, Iran

Stress analysis of critical line based on critical line list

Design checking of general arrangement and isometric drawings for plant piping

Review all Project/Job Specifications with regard to piping requirements.

Review layouts and detailed drawings for accuracy to assembly drawings.

Responsible for preparing as built, plant layout, mechanical and piping design drawings

Ensuring drawing packages are delivered within the project time schedule.

Prepare Report for Piping/Mechanical Engineer Manager

Prepare and issue the piping stress design criteria and analysis specification.

Provide input to the Monthly Progress Report.

Stress analysis of KHAR- SIRI gas gathering system

Checking the local stress analysis, flange leakage and slug calculation.

Participate in issuing the project plant design and piping layout specification

Prepare the piping datasheet for expansion joints, spring hanger, strut and etc.

Design of pressure vessels and storage tanks with PV-Elite and Tank soft wares

Design of 40Km slurry pipeline carrying Copper concentrate slurry from Mining location to process facility for Sarcheshmeh Copper Complex as per ASME B31.11

EDUCATION

B.Sc DEGREE OF MECHANICAL ENGINEERING (Heat and Fluids) 1990-1995

Technical Faculty of Tabriz University, Tabriz, IRAN,

REGISTRATIONS/AFFILIATIONS

Registered as a professional engineer with APEGA

Member of ISME (Iranian Society of Mechanical Engineers)

Member of National Energy Committee (Universal Energy Council)

SPECIFIC TECHNICAL EXPERTISE/TRAINING COURSES

CAESAR II for piping stress design and Nozzle-Pro

PV-Elite for pressure vessels design

NavisWork, SmartPlant for 3D model review

Windows XP, Outlook, MS Office Tools ( Word, Excel, PowerPoint)

CSA pipeline course

Contact this candidate