Engineer Electrical
Resume:
Jack C. Hope
Virginia Beach, Va. 23455
****.*****@*****.***
757-***-**** (Cell)
757-***-**** (Home)
RESUME
SUMMARY OF QUALIFICATION
• Proto-type Design/Integration (R&D)
• System QA & Testing (in-process, final)
• Receipt Inspection, Metal/Hardware (Equipment Racks, critical dimensions, Structural Flaws,
Finish), iaw AutoCAD drawings, manufacturers specs.
• Red-Line Drawings (check drawings for correctness; as-built)
• Create: Integration Procedures; IDP (Installation Drawing Package); DRs, Documenting non-
conforming material
• System Integration/Upgrade (AN/SPS-48E(V) - ADP Rehost; NAVSSI; CDU; eCDU; NWS)
• Fabrication (proto-type systems; wire harnesses; Connectorizing (Crimp/solder cup; Mil-
spec/COTS connectors, Multi-pin) ; Wire wrap; Cable fabrication - CAT5e, CAT6, phone
• SMT Training – Certified by Northrop Grumman, based on J-STD-001 Class 3 requirements
(surface mount, through hole, solder cup), FOD, ESD
• System design and Install (IDS - Intrusion Detection System)
• Security+
• Large Data Center Infrastructure (racking & stacking gear, cable management, de-install)
• Network connectivity installation, troubleshooting & Repair SIPRNET, NIPRNET and Telephone
(IDF – Cross-connect telecommunications cable)
• Computer hardware-Move, Add, Change
• DPAS training
• Fiber optic Technician
• CISCO VoSIP – Configure, setup and install
• Fluke DTX-1800, MicroScanner2
• ISO9001/ AS9100 compliance
• MIL-STD-2042B Certified
• Remedy Trouble Ticket system
• Asset Management
• Installation of Burial and Aerial Cable
• Operate trenchers (Ditch Witch), JLG High-Lift and mini- backhoe, All-Terrain 4x4 forklift,
Scissor Lift
1
Jack C. Hope
EDUCATION
Tidewater Community College Virginia Beach, Va. 2009 – Present
Major: Engineering/Computer Science
Chemistry w/Lab (2 sem); Physics w/Lab (2 sem); Engineering Graphics; Computer Aided Drafting &
Design I; Intro to Computing; Computer Organization; Computer Science 1; Microcomputer Operating
System (A+); Intro to Network Concepts (Net+); Principles of Computer Security (Sec+); Technical
Report Writing I; College Composition I; Spanish 101/102; Introduction to Engineering; Calculus
Analytic Geometry II; First Aid and Safety; HIM 141 (Fundamentals of Health Information Systems I)
focusing on health data collection, storage, retrieval and reporting systems, with emphasis on the
IT/Networking side to accomplish the tasks, Using FreeMed, EHR database, small basic and mySQL.
Penn State Univ. Altoona, Pa. 1971
MAJOR: Engineering/ Biology
William Tennent H.S. Warminster, Pa. 1966-1970
SOFTWARE
Word; Excel; Power Point; Access;
Beginner: Autodesk Inventor; AutoCad; C++; FreeMed; EHR database; Small Basic; MySQL;
TOOLS and EQUIPMENT
Hand Tools; DVM; Fluke DTX-1800 Cable Analyzer; Fiber Optic Tester (fiber optic power meter, fiber
optic light source, OTDR); Fusion Splicer; Fluke MicroScanner2 Cable Verifier; Crimpers; Calipers;
Micrometers; Depth Gauge; Pipe Benders (Hand /Hydraulic); Boom Lifts (JLG); Scissor Lifts; Ditch
Witch; All-Terrain 4x4 Fork Lift; Mini-crawler Excavator;
CERTIFICATIONS
Comp Tia Security+
Institution: Comp Tia
Date Granted: 16-AUG-2013
Date Expires: 16-AUG-2016
Certified Fiber Optics Installer
Institution: ETAI
Date Granted: 22-AUG-2007
Date Expires: 22-AUG-2011 (Expired)
Certified Fiber Optics Technician
Institution: ETAI
Date Granted: 22-AUG-2007
Date Expires: 22-AUG-2011 (Expired)
MIL-STD-2042B Certified
Category: Fiber Optics
Institution: Amphenol Fiber Systems International
Date Granted: 03-AUG-2007
Date Expires: N/A
2
Jack C. Hope
EMPLOYMENT HISTORY
8/12/2013 to Trowbridge & Trowbridge LLC 7927 Ingersoll Ave. Suite 210
Present Norfolk, Va. 23551-2332
Help Desk Specialist
Involved with installing and maintaining the Data Center, network and phone infrastructure for US
Joint Staff at NSA Norfolk. Working with Remedy Trouble Ticket System - to include installing new
cable runs with CAT5E, CAT6, fiber and power as required by customers; troubleshooting and repairing
connectivity issues of network (SIPRNET and NIPRNET; Site survey, installing/upgrading/de-installing
equipment racks with servers, switches, PDUs, UPS and patch panels; Fabricate, test and certify CAT /
fiber cables using Fluke DTX 1800 Cable Analyzer and Fluke MicoScanner2 Cable Verifier.
10/19/2009 to LOCKHEED MARTIN, IS&GS 7927 Ingersoll Ave. Suite 210
7/31/2013 Norfolk, Va. 23551-2332
Technician Telecom Sr Spec
Work with asset management; passing required training modules in DPAS, involved with
Inventory barcoding and deploying asset tags, LCM, and Computer Hardware move, add and change on
location at JWC in Suffolk, VA.
I was involved with installing and maintaining the Data Center, network and phone infrastructure
for US Joint Forces Command across 14 buildings at NSA Norfolk and JCW Suffolk. Working with
Remedy Trouble Ticket System - to include installing new cable runs with CAT5E, CAT6, fiber and
power as required by customers; troubleshooting and repairing connectivity issues of network (SIPRNET
and NIPRNET) and phone systems; Installation and de-installation of Peripheral Network equipment such
as cable racks, cable wiring systems, patch panels; Cross-connect IDF and patch panels adding new users,
moving phone and network to new locations; Configure/Setup and Install Cisco VoSIP phone; Site
survey, installing/upgrading and connecting new equipment racks with servers, switches, PDUs, UPS and
patch panels; installed conduit runs. Fabricate, test and certify CAT / fiber cables using Fluke DTX 1800
Cable Analyzer and Fluke MicoScanner2 Cable Verifier.
9/28/2009 to NORTHROP GRUMMAN, ES 7323 Aviation Blvd
10/15/09 Linthicum, Md. 21090
Electronic Manufacturing Specialist
To qualify for employment, I successfully completed SMT training in accordance with J-STD-001
Class 3 requirements. Training consisted of soldering through-holes, surface mount, solder cup; FOD;
ESD.
6/3/1996 to NORTHROP GRUMMAN, MS 2700 International Pkwy
11/25/2008 Virginia Beach, Va. 23452
SCA Electronics Technician, Maint II
Primary assignment was in the integration of the AN/SPS-48E(V); Command Work Station (CWS)
and Remote Station (NRS)Block 4. R&D of NRS Block4 designing the NRS 4.2.1; AN/SPS48E;
CDU and ACDS Block 0 Command Work Station. Designed the first NRS-Block4 successfully
passing shock and vibe test. Installed NAVSSI (Block3) at Dam Neck Fleet Combat Training Center.
Responsible for the fabrication/integration/testing and software load of the AN/SSN-6 Block 2,
3
Jack C. Hope
Navigation System Sensor Interface (NAVSSI) equipment.
Integrated and assisted in the design of the AN/SPS-48E(V) - 48E Rehost. Created integration
procedures and updated with engineering changes as implemented; Reviewed and redline integration
procedures, drawing package and BOM assuring most up to date information. Update project
engineer and integration facility supervisor of impending design/production problems, suggesting and
implementing fixes so as not to impact delivery schedule.
Fabricated and inspected power and interface cables/wires and wiring harnesses (MIL connectors,
crimp and solder cup); modify racks to accommodate components; install power and interface wiring,
and install components and assemblies. Experienced with fiber optic cables and electrical/electronic
equipment layout, installation, test/checkout, maintenance, and repair. Responsible for training cable
fabricators; Fabricate custom wire harnesses, power cables, RF cables (Coax/Triax), multi conductor
data cables, connectorizing (Crimp/solder cup; military/ COTS connectors).
Responsible for writing integration procedures for AN/SPS-48E (ADP), NWS, eCDU AND CDU;
Reviewing and red-lining drawing packages for AN/SPS-48E, NWS (Block3/Block4). Performed
receipt inspection of hardware, fabricated parts and equipment used in all projects; Receipt Inspection
Metal (critical dimensions, Structural Flaws, Finish); On-site inspection of metal fabricated parts at
the vendors before going to paint shop; Create DRs; Document non-conforming material;
AS9100/ISO9001 compliant.
.
10/3/1988 to TRACOR INC. 821 Live Oak Dr.
5/31/1996 Chesapeake, Va. 23320
Electrician II
Intrusion Detection System (IDS): primarily involved with the design and installation of the
security system, intrusion detection and access control, at various bases around the U.S., Japan and
Okinawa. The tasks involved measuring, cut, bend, thread, assemble and install electrical conduit; running/
splicing burial and aerial cable; pulling wire and cables through conduit, manholes, across small bridges
and hooking up access control, IR sensors, control boxes, power, phone systems and computer systems;
Testing continuity of circuits to ensure electrical compatibility and safety compliance and and Hi-Pot
testing of cable trunks before and after installation; Create as-built drawings depicting necessary changes
due to unexpected conflicts in planned conduit runs; also ran fiber-optic cable terminating and splicing
using conventional connectors and also a fusion splicer. Responsible for maintaining the systems across
four marine bases after the installation was completed, while in Okinawa. While working closely with
Project Engineers and site survey pictures, I was involved with the IDPs of the IDS for many bases: which
included equipment layout, developing a materials list, schematics (data, phone, power and fiber).
Install communication equipment on USN Special Warfare boats (HSB) out of Dam Neck Fleet
Combat Training Center.
Assisted in the research and design of circuit boards for special projects.
Worked on the Task Unit Van (TUV), installing communication systems and crypto equipment.
Operated trenchers (Ditch Witch), JLG, scissor lift, heavy-duty 4x4 forklift and mini-backhoe.
3/1988 to ABACUS TECHNICAL 2600 Potters Rd.
8/1988 SERVICES, INC. Virginia Beach, Va. 23464
Field Engineer Tech B
Computer systems installation: Subcontracted by UNISYS at the Fleet Combat Training Center,
Atlantic-Dam Neck. The contract consisted of the integration of peripherals in the PGC of FCDSA.
Equipment included UYK 43, UYK 7, UYK 20, VAX, PACX GANDALF, modems, switches and the
main distribution frame. My tasks also included cable fabrication and wire wrapping.
4
Jack C. Hope
3/1987 to CDI CORP. 5775 Wayzata Blvd., Suite 180
3/1988 St. Louis Park, MN. 55416
Electrical Installation Tech
(Contract picked up by ABACUS – Same job description)
8/1986 to Unidyne Corp. 3835 E. Princess Anne Rd.
11/1986 Norfolk, Va. 23502
Electrical Installation Tech
Duties included final installation (connectorizing cables) of various weapons systems: CIWS, Sea
sparrow Controller MK 117 and Director, aboard the USS EISENHOWER. Fabrication of power
connectors, high-density connectors, coaxial and triaxial connectors, inspected cables for quality,
continuity and hi-pot tests.
9/1978 to Kellett Corp Prudential Business Campus
6/1986 Horsham, Pa. 19844
Lead Electrical Tech/ Foreman
Duties included supervising and instructing up to ten employees. I installed power (120VAC;
220VAC; 1ph/3ph and 60 / 400 Hz), data lines, lighting fixtures and breaker panels while integrating
mobile communication shelters, photographic shelters and electronic work shelters. Fabricated and wired
prototypes of various hydraulic aircraft engine test equipment, control panels, instrument panels and
junction boxes. Worked directly with project engineers, red line production drawings and relaying
necessary changes. Held a company approved solder certificate and worked in accordance with
schematics, wire diagrams, shop blue prints. Hydraulic leak test
5
Jack C. Hope
Contact this candidate