Ben Dinh
408-***-**** ac1w60@r.postjobfree.com
Executive Summary
Over 10 years' experience as an engineer technician/assembler. PLC troubleshooting experience and troubles-shooting component level and system. Ability to operate electronic equipment such as spectrum analyzers, power supplies, volt ohmmeters and oscilloscopes. Excellent hand soldering SMT and through hold. Proficient in Lab-View Software.
Professional Experience
Smith INC 2/17-present
Newark CA.
Electronic technician
Examined performance of electro-mechanical assemblies, using test instruments such as oscilloscopes,
electronic voltmeters, and bridges.
• Studied blueprints, schematics, diagrams, and technical orders to determine methods and sequences of
assembly.
• Installed electrical, electronic parts and hardware in housings or assemblies using soldering equipment and
hand tools.
• Aligned, fitted, and assembled component parts using hand tools, power tools, fixtures, templates, and
microscopes.
• Operated, tested, and maintained robotic equipment. Trouble-shooting PLC.
• Repaired, reworked, and calibrated hydraulic pneumatic assemblies and systems to meet operational
specifications and tolerances.
Festo Inc. 6/6 - 11/16
Livermore CA
Mechanical test technician/Assembler
• Assembled and manually build electronic components, including print circuit board and cable harness using hand tools and power tools.
• Tested electronics units, using standard test equipment, to evaluate performance and necessary adjustments.
• Adjusted and replaced defective circuit and electronic components, using hand tools and soldering irons.
• Reviewed blueprint, wiring diagrams, schematic drawings, and engineering instructions to install multiple engineering systems.
• Trouble-shoot and repaired printed circuit boards solder and unsolder SMT components.
• Tested techniques, laboratory equipment, and installation specifications.
• Identified and resolved equipment malfunctions as well as performed preventative maintenance on equipment and systems.
Plexus Inc. 5/15-6/16
Fremont CA
Test technician/Assembler
• Tuned, and tested RF/microwave components including solid-state switch, filters and power dividers, in both production and engineering. Tested high power amplifiers using appropriate test procedure.
• Repaired fiber optic transmitters and receivers through troubleshooting and RF measurements.
• Debugged failure on transceiver and transponder product during test based on FA process.
• Manually wire bonded, with bond machines and trouble-shoot board to component level.
• Automated alignment systems for fiber optic.
• Adjust laser and alignment laser.
• Splice single optical fibers. Built prototype fiber optic
Protein Simple 1/15-5/15
San Jose CA
Electronic Technician/Assembler
• Examined performance of electro-mechanical assemblies, using test instruments such as oscilloscopes, electronic voltmeters, and bridges.
• Studied blueprints, schematics, diagrams, and technical orders to determine methods and sequences of assembly.
• Installed electrical, electronic parts and hardware in housings or assemblies using soldering equipment and hand tools.
• Aligned, fitted, and assembled component parts using hand tools, power tools, fixtures, templates, and microscopes.
• Operated, tested, and maintained robotic equipment used for green production applications such as waste-to-energy conversion system.
• Repaired, reworked, and calibrated hydraulic pneumatic assemblies and systems to meet operational specifications and tolerances.
Bridge Analyzer Inc. 9/12-5/14
Alameda CA
Electronic Technician/Assembler
• Examined performance of electro-mechanical assemblies, using test instruments such as oscilloscopes, electronic voltmeters, and bridges.
• Studied blueprints, schematics, diagrams, and technical orders to determine methods and sequences of assembly.
• Installed electrical, electronic parts and hardware in housings or assemblies using soldering equipment and hand tools.
• Aligned, fitted, and assembled component parts using hand tools, power tools, fixtures, templates, and microscopes.
• Operated, tested, and maintained robotic equipment used for green production applications such as waste-to-energy conversion system.
• Repaired, reworked, and calibrated hydraulic pneumatic assemblies and systems to meet operational specifications and tolerances.
Pacific Gaming Inc. 2/09-3/12
Technician/Assembler
• Assembled and manually build electronic components, including print circuit board and cable harness using hand tools and power tools.
• Tested electronics units, using standard test equipment, to evaluate performance and necessary adjustments.
• Adjusted and replaced defective circuit and electronic components, using hand tools and soldering irons.
• Reviewed blueprint, wiring diagrams, schematic drawings, and engineering instructions to install multiple engineering systems.
• Trouble-shoot and repaired printed circuit boards solder and unsolder SMT components.
• Tested techniques, laboratory equipment, and installation specifications.
• Identified and resolved equipment malfunctions as well as performed preventative maintenance on equipment and systems.
Zhone Technologies Inc. 7/03-1/09
Test Technician /Assembler
• Tuned, and tested RF/microwave components including solid-state switch, filters and power dividers, in both production and engineering. Tested high power amplifiers using appropriate test procedure.
• Repaired fiber optic transmitters and receivers through troubleshooting and RF measurements.
• Debugged failure on transceiver and transponder product during test based on FA process.
• Manually wire bonded, with bond machines and trouble-shoot board to component level.
• Automated alignment systems for fiber optic.
• Adjust laser and alignment laser.
• Splice single optical fibers. Built prototype fiber optic.
Education
• High School Diploma, McLane High School, Fresno, CA
• A.S electronic system Chabot College, CA
Licenses / Certifications
• Certificate of Industrial Electronic Technology, Chabot College, Hayward, CA
• Certificate of Consumer Technology, Chabot College, Hayward, CA