Piping Superintendent

CURRICULUM VITAE

POSITION APPLIED FOR : PIPING SUPERINTENDENT

NAME : VIRGILIO A. MARQUEZ

ADDRESS : POB. SAN PASCUAL, BATANGAS CITY, PHILIPPINES

DATE OF BIRTH : JANUARY 02, 1959

PLACE OF BIRTH : SAN PASCUAL, BATANGAS

CIVIL STATUS : MARRIED

NATIONALITY : FILIPINO

DIALECT SPEAKING : ENGLISH / TAGALOG

PASSPORT No. : EC1293516 (Till June 2019)

HEIGHT : 5’6 1/2”

WEIGHT : 184 LBS.

RELIGION : ROMAN CATHOLIC

EDUCATIONAL ATTAINMENT : MECHANICAL ENGINEER

CONTACT TEL. NO. : +966-********* – HP Jizan, SaudiArabia

+634*-******* – Land line Tel. No. Philippines

+639**-******* – Hand phone Phlippines

E-mail - **************@*****.***

SUMMARY OF EXPERIENCE:

TOTAL OF 32 YEARS EXPERIENCE IN PIPING, MECHANICAL & STRUCTURE CONSTRUCTION. FABRICATION ASSEMBLING OF STRUCTURE, PIPERACKS, DIFFERENT KINDS OF PIPING ARRANGEMENT, & EQUIPMENT ERECTION, IE PRESSURE VESSEL, COLUMNS, DRUMS, PUMPS, COMPRESSORS, FIN FAN COOLERS, EQUIPMENT PACKAGE AND HRSG’S. INSTALLATION & COMMISSIONING, TANK FABRICATION / ERECTION / LEAK TESTING & HYDROTESTING. PROJECT COORDINATOR / CONSTRUCTION SUPERVISOR AND INSPECTION. 9 YEARS AS MECHANICAL AND PIPING INSPECTOR, 7 YEARS AS COMMISSIONING SUPERVISOR, 13 YEARS AS MECHANICAL, PIPING & CONSTRUCTION SUPERVISOR, 3 YEARS AS PIPING FOREMAN. KNOWLEDGE IN MECHANICAL, PIPING & STRUCTURE WORKS, CODES & SPECIFICATION.

EMPLOYMENT HISTORY

INCLUSIVE DATE : AUGUST 27, 2015 TO PRESENT

COMPANY : CONSOLIDATED CONTRACTORS COMPANY. (CCC)

ADDRESS : JIZAN, SAUDI ARABIA

PROJECT : JIZAN SULPUR RECOVERY UNIT (JSRU)

PACKAGE 2 PROJECT

POSITION HELD : SENIOR QA/QC SUPERVISOR (MECHANICA & PIPING)

INCLUSIVE DATE : MAY 21, 2013 TO JUNE 15, 2015

COMPANY : DAEWOO ENGINEERING & CONSTRUCTION (EPC)

ADDRESS : JUBAIL, SAUDI ARABIA

PROJECT : SADARA TANK FARM PROJECT

POSITION HELD : QA/QC SUPERVISOR (MECHANICAL PIPING)

INCLUSIVE DATE : DECEMBER 2012 TO FEBRUARY 2013

COMPANY : TEKFEN CONSTRUCTION & INSTALLATION CO. INC.

J/V WITH AMEC & AZFEN(EPC)

ADDRESS : SABIL DISTRICT, BAYIL, BAKU AZ1023, AZERBAIJAN

PROJECT : COP-WC-PDQ (CHIRAQ OIL PROJECT-WESTCHIRAQ-PDQ)

ON-SHORE TOPSIDE MODULE FABRICATION

POSITION HELD : SR. MECHANICAL & PIPING QA/QC INSPECTOR

INCLUSIVE DATE : SEPTEMBER 2010 TO DECEMBER 2012

COMPANY : TEKFEN CONSTRUCTION & INSTALLATION CO. INC. (EPC)

ADDRESS : 6th FLOOR, MAZYAD MALL FIRST TOWER, MOHAMAD

BIN ZAYED CITY, MUSAFFAH, ABU DHABI, UAE

PROJECT : ADCO-ASAB FFD M&I PROJECT

POSITION HELD : SR. MECHANICAL, PIPING & PRE-COMMISSIONING INSPECTOR /

SUPERVISOR

INCLUSIVE DATE : NOVEMBER 2009 TO FEBRUARY 2010

COMPANY : OMNIUM de TRAITMENT et de VALORIZATION(OTV) (EPC)

ADDRESS : FASEEL ROAD, QIDFAH, P.O. BOX 4168, FUJAIRAH, UAE

PROJECT : FUJAIRAH 2 POWER and WATER PLANT PROJECT

POSITION HELD : MECHANICAL & PIPING INSPECTOR / SUPERVISOR

INCLUSIVE DATE : AUGUST 2008 TO AUGUST 2009

COMPANY : SNAMPROGETTI S.P.A. (EPMC)

ADDRESS : AL RUWAIS INDUSTRIAL COMPLEX

AL RUWAIS, ABU DHABI, UAE

PROJECT : GASCO LNG TRAIN 3 PROJECT

POSITION HELD : MECHANICAL PIPING SUPERVISOR

INCLUSIVE DAT : OCTOBER 2007 TO FEBRUARY 2008

COMPANY : MALAI MASHHOR GENERAL CONTRACTOR

ADDRESS : G-22 LOT 3698, JALANPANGSA, SERIA, BRUNEI

PROJECT : COOLING WATER SYSTEM REJUNIVATION

(CWSR) PROJECT (BLNG)

POSITION HELD : MECHANICAL & PIPING SUPERVISOR

INCLUSIVE DATE : JULY 2006 TOAUGUST 2007

COMPANY : JURUNG ENGINEERING LIMITED (JEL)

ADDRESS J : JALAN BUKIT PANGGAL, TUTONG

PROJECT : BUKIT PANGGAL COMBINED CYCLE POWER PLANT

STATION PROJECT – PHASE 1

POSITION HELD : MECHANICAL & PIPING SUPERVISOR

INCLUSIVE DATE : FEBRUARY 2005 TO JUNE 2006

COMPANY : CHIN WUI HENG WELDER ENTERPRISE (CWHWE)

ADDRESS : LOT 7872, KAMPONG WASAN, LIMAUMANIS

BRUENI, DARUSSALAM

PROJECT : MUARA NAVAL BASE EXPANSION PROJECT

: BSP SCOT TANK5 CONSTRUCTION/

DEMOLITION PROJECT (AWE-PROTANK)

: BUKIT PANGGAL COMBINED CYCLE POWER

STATION PROJECT (PHASE 1) TANK

FABRICATION & ERECTION

POSITION HELD : PROJECT SUPERVISOR / COORDINATOR / INSPECTOR

(MECHANICAL /STRUCTURAL/PIPING / COMMISSIONING)

INCLUSIVE DATE : SEPTEMBER 2001 TO DECEMBER 2004

COMPANY : OGP TECHNICAL SERVICES SDN. BHD. (EPMC)

ADDRESS : SITE OFFICE, AMPA FAIRLEY RATIONALIZATION PROJECT

LOT 3790, LUMUT KC2935, SERIA,NEGARA BRUNEI DARUSSALAM

PROJECT : AMPA FAIRLEY RATIONALIZATION PROJECT

ONSHORE GAS COMPRESSION PLANT PROJECT (OCP)

(BSP/BLNG)& INSTALLATION OF 3 HRSG, BOILER.

POSITION HELD : MECHANICAL/ PIPING / CONSTRUCTION

PRE-COMMISSIOING / COMMISSIONING SUPERVISOR

SUPERINTENDENT / SENIOR MAINTENANCE SUPERVISOR

OPERATION & MAINTENANCE SUPPORT (OMS)

INCLUSIVE DATE : JULY 2000 TO AUGUST 2001

COMPANY : SYARIKAT KEJURUTERAAN SISTEMATIC SDN.

BHD. (SKS) CWHWE AS SUB – CONTRUCTOR

ADDRESS : P.O. BOX 105, SERIA

LOT 23, G-25 SIMPANG 81-4

JALAN BADAS SERIA

NEGARA BRUNEI DARUSSALAM

PROJECT : AMPA FAIRLEY RATIONALIZATION PROJECT

ONSHORE GAS COMPRESSION PLANT PROJECT (OCP)

(BSP/BLNG)

POSITION HELD : MECHANICAL, PIPING & PRE-COMMISSIONING SUPERVISOR

INCLUSIVE DATE : AUGUST 1999 TO MARCH 2000

COMPANY : CLOUGH / HAJI MALAI MASHOR JOINT VENTURE (EPC)

ADDRESS : PO. BOX 30, SERIA 700

G-22 LOT 3698, JALAN PANGSA SERIA

NEGARA BRUNEI DARUSSALAM

PROJECT : SAINT TUTONG GAS LINE PROJECT/COMMISSIONING (BSP/EPM)

POSITION HELD : MECHANICAL, PIPING & COMMISSIONG SUPERVISOR

INCLUSIVE DATE : FEBUARY 1997 TO AUGUST 1999

COMPANY : SAHID SDN. BHD.

ADDRESS : LOT 2385, SPG. 82-11, JALAN BOLKIA, SERIA

NEGARA BRUNEI DARUSSALAM

PROJECT : TUNGKU GAS PLANT PROJECT, BRUNEI SHELL PETROLEUM (BSP/EPM)

: SSU KB WRAFT PROJECT / COMMISSIONING (BSP/EPM)

: CHLORINATION PROJECT / COMMISSIONING (BSP/EPM)

: TERMINAL SERIA EMULTION TREATMENT PLANT

DEMOLITION (ETP), (BSP/EPM)

: SERIA TERMINAL TANK 170 COMMISSIONING(BSP/EPM)

POSITION HELD : MECHANICAL, PIPING & COMMISSIONING SUPERVISOR

INCLUSIVE DATE : JUNE 1996 TO FEBRUARY 1997

COMPANY : ATLANTIC GULF & PACIFIC Co. (AG&P)

ADDRESS : SAN ROQUE, BAUAN, BATANGAS

PROJECT : SEA VAM AND ACRU MODULE PROJECT OF

SINGAPORE

POSITION HELD : MECHANICAL & PIPING SUPERVISOR

INCLUSIVE DATE : AUGUST 1995 TO MAY 1996

COMPANY : COGENT CONSOLIDATED CONT. (M) SDN. BH.

ADDRESS : LOT 116, KAWASAN INDUSTRIAL GEBENG, 26080

KUANTAN, PAHANG DARUL MAKMUR, WEST MALAYSIA

PROJECT : AMOCO PTA. PLANT (PETRO-CHEMICAL PROJECT)

POSITION HELD : PIPING SUPERVISOR

INCLUSIVE DATE : JUNE 1994 TO APRIL 1995

COMPANY : HYUNDAI DOZ (M) ENGINEEREING CORP.

ADDRESS : P.O. BOX 745, BINTULU, SARAWAK, EAST MALYSIA 97008

PROJECT : MALAYSIA LIQUIFIED NATURAL GAS (MLNG II) EXPANSION PROJECT

POSITION HELD : PIPING SUPERVISOR

INCLUSIVE DATE : JULY 1993 TO JUNE 1994

COMPANY : METAPHIL INCORPORATED

ADDRESS : POBLACION SAN PASCUAL, BATANGAS

PROJECT : CALTEX-DE BOTTLE NECK PROJECT

POSITION HELD : MECHANICAL & PIPING SUPERVISOR

INCLUSIVE DATE : SEPTEMBER 1992 TO JUNE 1993

COMPANY : D.M. CONSUNJI INCORPORATED

ADDRESS : BARRIO TABANGAO, BATANGAS CITY

PROJECT : FILIPINAS SHELL EXPANSION PROJECT

POSITION HELD : PIPING FOREMAN

(FABRICATION & FIELD ERECTION)

INCLUSIVE DATE : AUGUST 1991 TO APRIL 1992

COMPANY : SANKO ENGINEERING CORPORATION

ADDRESS : P.O. BOX 55826, TAIZE REPUBLIC OF YEMEN

PROJECT : MAFRAQ CEMENT PLANT PROJECT

POSITION HELD : MECHANICAL,PIPING & STRUCTURAL FOREMAN

(FABRICATION & FIELD ERECTION)

INCLUSIVE DATE : MAY 1982 TO JUNE 1987

COMPANY : ARABIAN AMERICAN OIL CO. (ARAMCO)

ADDRESS : P.O. BOX 1448, DHARAN, SAUDI ARABIA

PROJECT : MAINTENANCE WORKS, ARAMCO EAST-WEST CRUDE

AND GAS PIPELINE

POSITION HELD : MAINTENANCE CRAFTSMAN MECHANIC

DUTIES AND RESPONSIBILITIES :

1. Carries all Construction Monitoring & Supervision regarding the on-going fabrication & erection. Implementing inspection as per approved Procedure, ITP’s, Quality Control Plan (QCP), Codes & Standards. Attend weekly QA/QC meeting with the client. Verified all the LBE arrisen discuss with the client and replied. Implement & issue NCR as per project specifications & requirements.

2.Carries all Construction,Pre-Commissioning, Supervision, Inspection,Testing & Nitrogen Testing required by the project specification, approved quality control plan (QCP) and procedures, codes & standards. Implementation of NCR and Maintenance of the Company site quality management system.

3.Carried out the Inspection as per Project Specs and doing inspection of necessary Under ground / Aboveground (HDPE, GRE, GRP, Carbon Steel, Stainless Steel, Super Duplex, Duplex), pipelines and equipment installed on site. Checked with Sub-con QA/QC for the Inspection required as per Inspection and Test Plan (ITP). Go with the client and Sub-con in doing walk down of necessary Test Package. Checking Inspection of System and Sub System as per support list and procedure required before doing the Hydro-testing. Do punch listing of lines and equipments as per System and Sub-system. Witness the hydro-testing and N2 purging as per procedure required. Checking of necessary punch item if been cleared and line are-installed before signing the Mechanical Completion Certificate (MC).

4.Monitoring of contractor activities at site. Checking of contractors activilties if following as per Inspection & Test Plan (ITP). Checking of line and support discrepancy, and check with engineering regarding the required changes. Coordinating with the in-line Superintendent regarding the completed lines that been completed and the queries arised. Go with the client, sub-con and company QA/QC in doing walk down of System & Sub-system of lines. Do punch listing of lines as per System and Sub-system and coordinate with QA/QC before doing the hydro-testing. Checking of all calibration certificate of all the equipment to be use for hydro-testing. Coordinate with Sub-con QA/QC and checked for the necessary punch item (A) if cleared before doing the hydro-testing.

5.Checking for structure and piping layout’s before cutting and checking of fit-up of pipe, pipe spool and structure before doing any welding. Checking of construction activities if as per Inspection & Test Plan (ITP). Checking for the elevation of pipe slippers and pipe racks before allowing the pipe lines to be erected. Inspection of line as per test pack, check for fit-up & weldments, check for the NDT requirements. Do report for inspection to main company QA/QC. Request for hydro-testing of line, clearing of puchlist required by the main company. Submit all necessary test pack for approval. Supervision in field Piping Erection, Hydro testing, N2 purging of lines and pipe spools. Lay-out / erection of all necessary platforms required. Checking for calibration certificate of all pressure gauges, relief valves, hydro-test manifolds, and recording chart, same as the necessary check valves to be use before doing the hydro-testing. Check for field queries and revisions as per field requirements. Do checking in doing bolt tentioning of necessary flange connection if as per project requirement . Do final surveying of concrete base for pumps and motor before doing the final installation. Doing punch listing of System and Sub-system. Coordinate with company QA/QC for the final walk down and Inspection required.

6.Do line checking as per system and sub-system for required as built. Supervise in field Erection / Installation of Equipments, HRSG, BOP Piping Systems and Hydro-testing. Checking for calibration certificate of all pressure gauges, relief valves, hydro-test manifolds, and recording chart, same as the necessary check valves to be use before doing hydro-testing. Checking of construction activilties if as per Inspection & Test Plan (ITP) requirement. Coordinate with company and client representative for the inspection required for each activities that being done. Make necessary Test Package and Inspection Package for the system that been done and submit to the client for approval. Do valve and support checklist required for each system and submit to client for verification and approval. Coordinate with QA/QC and with the client representatives in doing walk down of System & Sub System of lines. Do punch listing of lines as per System and Sub-System and coordinate with QA/QC before doing the hydro-testing. Checking of necessarry lines if re-instated after hydro-testing and all punch list are being cleared. Coordinate with the client’s representative for final walk down.

7.Permit Coordinator (PTW) for all Pre-Commissioning, Commissioning and in the on-going Contruction works. Liase with Client Operation for the Job Hazard Analysis (JHA) and revert any changes in work. Checking of Test Package as per System and Sub System if necesary punch item (A) as per construction is been closed, Inspection & Test Plan (ITP) is followed thru out the construction phase and Mechanical Completion Certificate (MC) is signed and released for Pre-Commissioning. Coordinate with Commissioning Manager regarding the Commissioning requirements for as per System and Sub System. Check and applied for the necessary Work Permit required as per System and Sub-System. Engaged in Commissioning of Heat Recovery Steam Generation (HRSG) such as go with the client representative in doing inspection of boiler drums, boiler casing and necessary boiler lines. Supervise in preparation till completion of Boiler Chemical Cleaning and Steam Blowing of 20” dia. main steam header line and 10” dia. steam line from the HRSG, and check the steam line cleanliness thru brass target plate. Supervise in doing Nitrogen (N2) blancketing of Boiler Drums. Supervise for doing fan blade angle pitch inspection and adjustment of gas and lube oil coolers. Checking out the system as per PEFS drawing, issue, instruct and check out the lines to be commission before the Company representative. Doing request to Company, discuss the system and sub-system to be commission and raise up the necessary permits required. Supervise in doing air blowing of necessary lines such as airline, tool airline, nitrogen line and main gas line for line clean liness with 7barg pressure, and water flushing for line cleanliness of fire water line, service water line, and denim water line. Go with the client in doing inspection of Compressors Suction and Discharge Scrubber Vessels. Checking of all relief valve certification use in plant and sent them for re-calibration and Pop Testing of client’s approved calibration company. Supervision in doing bolt tentioning of necessary Gas Line Flange connection and for the boiler lines if as per project requirements. Doing Pop Testing of relief valve install in HRSG main Boiler Drum and in the Super Heater. Supervise in doing Nitrogen (N2) leak testing with pressure of 33 barg of main Compressor Suction and Discharge Line. Supervise in nitrogen purging of main Gas Fuel Lines before Gas-in, same as the main Compressor Suction and Discharge Header Lines. The reading must be zero oxygen percent on lines. Supervise in all necessary gas line tie-in’s from existing lines to new lines. Supervise in commissioning of 2 phase and 3 phase Separators, and checking for function of all control valve in line, and for the commissioning of all underground Drain Vessels and Flare Knock Off (KO) Drums, till lighting up of Flare System. Assist Electrical and Instrumentation in Supervision for loop checking and electrical motors direction and vibration checking. Assist GE/NP representative in doing over speed test and line function test for turbine to trip. Run the turbine for 24hrs, 3 days and 1 week performance run. Act as Company Single Person Responsible (SPR) for everyweek end of the construction plant.

During OMS Period

1)Checking/monitoring of Fuel Gas Filter differential pressure and switching of filter from on-line to standby if it is reach the maximum pressure required for the in-line filter.

2)Monitoring of Turbine Gas and Lube Oil temperature same as for the vibration of Gas and Lube Oil Fan Motors.

3)Checking/monitoring of Turbine Performance, record and report to the Operation Manager for the abnormalities found out. Coordinate with the client operation on duty regarding the day to day Turbine operation. If there is some abnormalities found out, check and coordinate with the operation personnel. Check / study in the Turbine hard copy and check with the client operation for shutdown schedule. Check and prepare all the necessary materials required, and coordinate with the Engineering Maintenance Personnel regarding the manpower, equipment and tools for the work to be done.

4)Coordinate with the Turbine Control Engineer, regarding the hours run by the Turbine in the first year of operation. Report to the OMS Manager regarding the first Combustion Inspection (CI) of the Turbine when it reaches 8,000 hours or to a maximum of 16,000 hours,

5)Coordinate with the OMS Manager and NP/GE regarding the manpower requirement for the C.I. to be done, I.E. the turbine technician, personnel to assist, equipment and tools required. Check/prepare all necessary materials required for the C.I., especially the turbine liner. Coordinate with the operation for the closing of necessary block off valves and control valves and lines to be block off or spaded, nitrogen purging of lines and override/lock off carbon dioxide lines. Full Supervision and coordination with the Turbine Technician and Engineering Maintenance Personnel thru out the C.I. work, till start up.

6)During Combustion Inspection time, HRSG will be open and check/repair all necessary damage been found internally.

8.Check and review the sub-contructor’s approved Method of Statements, and monitor the implementation of approved Method Statements.

9.Conduct daily toolbox talk and discuss the work activity & risk for the job to be done and re-toolbox talk again if there’s some changes regarding the work activity.

10.Prepare necessary work permit required for fabrication and in field works. Liase with client operation on duty for the gas test required. Revert any changes in work with the operation.

11.Supervise shop fabrication and field erection / installations of various pipe racks, tanks, pressure vessels, exchangers, pumps & motor and all the necessary equipment, required in various Refineries, Gas Plant, Petro Chemical Plant and Power Plant Project.

12.Supervise shop fabrication and field erection of different piping arrangement such as Slug catcher, Pipelines, Refinery Plants, Gas Plants, Petro Chemicals and Power Plants, Regarding Pipes and Pipe Spool depending on size and schedules.

13.Review isometric drawings and prepare material take-off list as per isometric drawing.

14.Itemized required materials according to classifications, specifications and various types.

15.Supervision / Monitoring for the preparation and hydro testing of all pipe spools and pipelines.

16.Prepare 3 weeks look a-head schedule and weekly schedules and arrange manpower and equipment allocation according to each work activity requirement to as per priority and target date of completion.

17.Coordinate with the Project Manager and Client Representatives regarding Engineering queries and site modifications and/or revisions to suite site conditions.

18.Implements the Company and Clients Policies, rules, regulations and procedures regarding Health Safety and Environmental (HSE), protection through-out the construction phase

TRAINING / COURSES

COURSES ATTENDED

CONDUCTED BY

YEAR

Site Induction and Location Awareness, Confined Space, and Working in Height Awareness

Saipem / CCC Training Center

2015

H2S Training Course, Working in Height, Green & Brown Field Awareness, Excavation & Scaffolding Awareness, PTW.Writting of JHA.

Daewoo / Sadara Training Center

2013

H2S Training Course, Working in Height, Green & Brown Field Awareness, Excavation & Scaffolding Awareness, PTW

Petrofac Training Center

2011/2012

PTW for Work Authorization at Site & Authorization of Commissioning Permits and First Aid Course

Snamprogetti SPA HSE PTW TRAINING COURSE

2008 /

2009

Rigging and Slinging Course

Adinin Training &Development Centre SdnBhd

2008

Permit to Work

Brunei LNG SdnBhd

2008

Intervention Seminar/Training

Brunei LNG SdnBhd

2005

Competent Worksite Supervisor

Megamas Training CompanySdnBhd

2005

Managing Hazards at the Workplace

Megamas Training CompanySdnBhd

2005

Senior First Aid

Megamas Training CompanySdnBhd

2005

Breathing Apparatus Wearer / ConfinedSpace

Megamas Training CompanySdnBhd

2005

ConfinedSpaceAwareness

Brunei LNG SdnBhd

2004

Permit to Work

Brunei LNG SdnBhd

2000 / 2002

HSE Training for Supervisor

SahidSdnBhd

1998

BSP Permit to Work – Worksite Supervisor

Brunei Shell PetroleumCompanySdnBhd

1997

Rigging and Slinging Course

Adinin Training &Development Centre SdnBhd

1997

Safety Driving Course / Fork lift Operation

Adinin Training &Development Centre SdnBhd

1997

Basic First Aid Course

Adinin Training &Development Centre SdnBhd

1997

Issuing of work permits

Arabian American OilCompany

1986

Receiving of work permits

Arabian American OilCompany

1984

REFERENCES :

1.MR. MOHAMED ABDE

LATIF AHMED AZZAM : QA/QC MANAGER CONSOLIDATED CONSTRUCTION CO. (CCC)

JSRU PKG 2 PROJECT, JIZAN, SAUDI ARABIA

2. MR. DONG WON LEE : QA/QC MANAGER, DAEWOO ENGINEERING &

CONTRUCTION, SADARA TANK FARM PROJECT, AL JUBAIL,

SAUDI ARABIA TEL. NO. +966*********,

Email : **.***@*********.***

3. MR. MINJAE LEE : CONSTRUCTION MANAGER, DAEWOO ENGINEERING &

CONTRUCTION, SADARA TANK FARM PROJECT, AL JUBAIL,

SAUDI ARABIA TEL. NO. +966*********,

Email : ******.***@*********.***

4. MR. K. AKIN : QA/QC MANAGER TEKFEN CONSTRUCTION & INS. CO. INC.

ADCO ASAB FFD PROJECT, ABU DHABI, UAE.

5. HUSEYIN HARDIC : PROJECT MANAGER, TEKFEN CONSTRUCTION &

INSTALLATION CO. INC, ADCO ASB FFD PROJECT, ABU

DHABI, UAE

6. BULENT CARACHA : PROJECT MANAGER, TEKFEN CONSTRUCTION &

INSTALLATION CO. INC, CHIRAQ OIL PROJECT, ATA YARD 3

SOUTH QUAYSIDE, SABIL DISTRIC, BAYIL, BAKU AZ1023,

AZERBAIJAN

7. GIANLUCA STURBA : CONSTRUCTION MANAGER, GASCO NGL3

PROJECT, RUWAIS, ABU DHABI, UAE.

8. KAMIS BIN HJ KASSIM : LNG OPERATION COMMISSIONING COORDINATOR

AMPA FAIRLEY RATIONALIZATION PROJECT –

TEL: +673-******* - BRUNEI

9. KHAIRUL YUNUS : OMS MANAGER, OCP AMPA FAIRLEY RATIONALIZATION

OCP, BSP BLNG, BRUNEI.TEL. NO. +6016- 2803353 - MALAYSIA

VIRGILIO A. MARQUEZ

(APPLICANT’S SIGNATURE)

Contact this candidate