Hoang Nguyen

**** *** **** ** *** A***

Lancaster, CA 93534

qflhp8@r.postjobfree.com

650-***-**** (Cell)

OBJECTIVE: Seeking a career in Manufacturing Engineer position.

EDUCATION: MSME (Thermal and Fluid Engineering) 12/99

San Jose State University, San Jose, CA

BSME (Thermal and Fluid Engineering) 12/96

San Jose State University, San Jose, CA

EXPERIENCE:

Lockheed Martin Aeronautics, Palmdale, CA

Manufacturing Engineer Sr: 10/08-06/12

Supported production areas: lay-up composite detail parts, core bond assemblies, and composite leading edge bond assemblies.

Created Manufacturing Plan for the Wing Tip Lens-Frame bond process.

Created notch tool for manufacture to use on different bonded assemblies.

Created cure recipe for composite parts and composite assemblies per program requirement.

Provided assistance in autoclave and oven issue and resolve problem in time matter.

Provided technical assistance in needed manufacturing areas.

Provided technical guide to less experience staff.

Applied Lean Manufacturing discipline to coverage areas continuous flow production of flight hardware assemblies.

Provided short and long term solution to production process and continue improve MPS process of the Corporation initiatives’.

Streamlined and provided the IML casting procedure by using heat applications to cure liquid shim of bonded assemblies for production rate.

AltairUSA, Menlo Park, CA

Mechanical Engineer: 9/06-10/08

Utilized SolidWorks CAD tool for modeling and documentation creation.

Created CNC machine traveler per engineering drawing.

Revised engineering document per ECO.

Utilized CosmosWorks to investigate thermal profile and critical stresses on rigid body.

Prepared welding or brazing hardware and provide instructions per shop traveler.

Inspected and verified incoming hardware per client requirements.

Provided manufacture support in needed areas.

Albin Engineering Services, Mountain View, CA

Technical Consultant: 9/06-4/07

Utilized SolidWorks CAD tool for modeling and documentation creation.

Retrieved and migrated SolidWorks files (CAD and detail drawing) into PDMWorks vault.

Provided guidance to inexperienced staff members.

Revised engineering document per ECO.

Enhanced Lighting Inc., Brisbane, CA

Technical Consultant: 8/03-9/06

Utilized SolidWorks CAD tool for modeling and documentation creation.

Constructed and designed collapsible flat screen monitor mechanism for DJ system.

Constructed and designed light ascending fixture for airwall mechanism attachment.

Prepared event hardware per client request.

Maintain control of hardware inventory.

Review purchased orders and documented non-conformance items.

Provided on site client technical support.

Lockheed Martin, Sunnyvale, CA

Mechanical Design Engineer: 1/01-7/02

Developed 3D solid model flight hardware of antenna for structural and thermal analysis.

Utilized analysis tools DIAL and TOPAZ to perform thermal analysis on heat shield.

Generated and revised engineering documents using ProE, IDEAS and MCADAM.

Inspected hardware and resolved discrepancy reports to improve electronic assembly.

Provided manufacture support in needed areas.

Alignment Engineer: 8/99-12/00

Supported integration and testing of commercial satellites: Align thrusters, sensors and antennas for flight configurations relative to the spacecraft’s coordinate. Calculate required shim for thruster per system engineer requirement, Vibration, TVAC, Planar Near Filed Testing, Mass Properties, periodic inspections of solar array deployment rails and test L-fixtures, generate operational test procedures for Mass Properties, Planar Near Field Test and TVAC.

Provided alignment and environmental testing support to other programs.

Coordinated schedules with technicians’ supervisor to maintain mechanical ground support equipment.

A.G. Paceman Inc., San Carlos, CA

Incoming products Quality Inspector: 6/94-7/99

Examined quality of products per client requirements.

Maintained control of production inventory.

Trained staff member on procedure and method for inspection.

Reviewed purchase orders and documented non-conformance items.

PROJECTS: NCG Analysis in heat pipe for aviation application:

Analyzed generation of non-condensable gas and predicted life of aluminum-ammonia heat pipes for satellite applications.

Solar water pump design:

Designed and constructed a solar-powered system to transfer water to uncultivated areas. Estimated: 1) solar panel (frame) thermal stress and strain; and 2) structure displacement due to forced vibration (wind).

Feeding mechanism for the disabled:

Constructed and designed feeding mechanism to assist handicapped individuals with limited arm and hand movement.

ENGINEERING

TOOLS: CATIA, ProE, SolidWorks, IDEAS, MatLab, Fortran, DIAL and TOPAZ.

RELATED COURSE WORK:

Thermal/Fluid Engineering, Finite Element Analysis, Vibration of Mechanical Systems, Advanced Heat Transfer, Applied Stress Analysis, Advanced Thermal System Analysis, Viscous Flow Analysis, Fiber Optic Technology, Automatic Control Engineering, Geometric Dimensioning and Tolerancing Y14.5M-1994, HVAC, ProE for mechanical designers, Introduction to JAVA programming, SPC, RMP.

Contact this candidate