Silvo Stanojevic
SILVO ANALOG DESIGN SERVICES
Milpitas, CA 95035
Email: n3kz6x@r.postjobfree.com
Telephone: 408-***-****
Cell: 408-***-****
Title: Contractor
SILVO ANALOG DESIGN SERVICES provides complete design services for integrated circuits specializing in bipolar process. Services include circuit design, layout, DRC and LVS and IC debugging.
I have extensive circuit design experience in voltage regulators, references, and sensor signal conditioning. Majority of my designs have been implemented in bipolar process. However, I do have good understanding of the CMOS process and its device characteristics and have completed a couple designs in CMOS process and have also done some custom circuit design in MICREL biCMOS BCD1.2 process flow. “Areas of knowledge” section below lists types of circuits and technologies that I have been exposed to in my carrier as an IC designer. My resume follows on the next page.
Areas of knowledge: Op Amps
Voltage regulators standard and LDO
DC/DC low power switching regulator
Voltage references (shunt)
Photo current sensing
Peak Detector
Differential Logic
Bipolar ADC
LED driver (current source)
Hall Effect sensors
High/Low side drivers
Automotive environment
Inductive/capacitive position sensors
High voltage ckt. Design
Smart Power-DMOS/CMOS
Thin film trimming
Zener and metal link trimming
Watch-dog circuits
Lithium ion battery charger/protection
Silicon Accelerometer
Semi-customs circuit design
Bipolar process
CMOS process
BiCMOS process
Awarded 9 patents
RESUME
Silvo Stanojevic
641 Clauser Dr.
Milpitas, CA 95035
Email: n3kz6x@r.postjobfree.com
Telephone: 408-***-****
Areas of knowledge: Op Amps
Voltage regulators standard and LDO
DC/DC low power switching regulator
Voltage references (shunt)
Photo current sensing
Peak Detector
Differential Logic
Bipolar ADC
LED driver (current source)
Hall Effect sensors
High/Low side drivers
Automotive environment
Inductive/capacitive position sensors
High voltage ckt. Design
Smart Power-DMOS/CMOS
Thin film trimming
Zener and metal link trimming
Watch-dog circuits
Lithium ion battery charger/protection
Silicon Accelerometer
Semi-customs circuit design
Bipolar process
CMOS process
BiCMOS process
Awarded 9 patents
Personal: Birth date: 3-20-51
Married, 2 children
Excellent health
Education: San Jose State University, California
BSEE-1975
MSEE 1977
Experience:
March 1998 to present: Contractor, providing analog IC design and layout services to local semiconductor corporations.
Calogic, Sipex, ABORN ELECTRONICS, and FulTec, are major corporations that I have worked for as a contractor. Design examples of power management products, currently in production, can be found in EXAR’s (Sipex products) linear regulators data sheets such as SPX1580_7, SPX29150, SPX29300 families, SPX3819 and others including SPX431 voltage reference, SPX2970_2 LED driver and SPX4446 low power boost regulator.
June 1997 to February 1998: ALS Technologies Inc. (was start up)
643 Bair Island Rd., #200
Redwood City, CA 94063
Position: Senior Staff Engineer
Responsibilities: -Design and develop custom integrated circuits including layout.
-Support product planning and office management as needed.
Achievements -Designed 2 full-custom circuit in CMOS(50mA LDO and 1Watt Audio Power amplifier)
-Second sourced 1 bipolar circuit (power factor controller).
-Implemented DRC and LVS on ICED software for bipolar and CMOS process.
October 1996 to May 1997 Semtech Corporation
1111 Comstock Street
Santa Clara, CA 95054
Position: Staff Engineer
Responsibilities: -Design and develop custom integrated circuits
-Review RFQs
-Provide production product support
Achievements: -Designed 1 full-custom circuit (1.2V shunt regulator)
-Implemented DRC and LVS on ICED software for bipolar process.
-Designed test structures for isolated vertical PNP bipolar process.
March 1989 to September 1996 EXAR Corporation
48720 Kato Road
Fremont, CA 94538
Position: Staff Engineer
Responsibilities: -Design and develop custom integrated circuits
-Review and integrate semi-custom circuits
-Review RFQs
-Develop new cells for the semi-custom library
-Provide production product support
Achievements: -Completed 12 semi-custom circuits
-Designed 3 full-custom circuits (solid state transformer, two inductive proximity switches and intelligent driver)
-Completed SPC in house seminar
-Completed TQM in house seminar
-Applied for 4 patents
October 1983 to February 1989 National Semiconductor
2900 Semiconductor Dr.
Santa Clara, CA 95051
Position: Staff engineer
Responsibilities: -Design and develop custom automotive circuits
-New product definition
Achievements: -Designed High Side Driver
-Designed LDO regulator
-Designed stand-by/Power LDO
-Designed HV DMOS/LV CMOS kit parts
-Awarded 4 patents
May 1980 to October 1983 MICRO SWITCH
Freeport, Illinois
Position: Principal Design Engineer
Responsibilities: -Design and develop new linear circuits (concept to production stage)
-Write product specifications
Achievements: -Designed temperature compensated Hall Effect switch
-Designed gear tooth sensor (Hall Effect switch)
-Designed transient protection for the automotive applications
-Designed Permalloy low current sensor
-Awarded 4 patents
July 1977 to May 1980 Fairchild Camera & Instrument
Mountain View, CA
Responsibilities: -Design and develop new Op Amp and automotive circuits
-Support existing products
-Redesigns
-Competitor evaluation
Achievements: -Redesigned Ua124 and Ua7503 Op Amps
-Designed Automotive voltage regulator