MIRZA IQBAL BAIG

***** **** *** # ***

Torrance, CA 90503

310-***-**** Cell

310-***-**** Desk

Email: c34brk@r.postjobfree.com

TECHNICAL SKILLS

• Experienced in Project Management, Performs Technical writing, including proposals, Reports, Test procedures and Specifications.

• 2G, 3G and 4G RF Coverage Planning & Design Cell Sites, Optimization of GSM, GPRS, UMTS, CDMA2000, WiMAX and LTE Networks.

• 4G IMT-Advanced and LTE –Advanced, Training by Agilent Technologies, Anaheim, CA

• Transmission Planning for IP RAN with packet/ IP Radio

• Transmission Planning for rollout of 2G-3G HSDPA,HSPA,HSPA+ sites+ update and upgrade

• Supervised Planning & Design, Upgrade and Update also Operation group in the Maintenance, Operation and Field-Testing of Point-to-Point (PP) Fixed Networks and Point-to-Multipoint (PMP) at 6GHz and 7GHz bands NEC and TOSHIBA Microwave Backhaul Network, Repeaters and 12.5 GHz Satellite Base Station, as well as Multiplex Systems and National Wide Dialing Systems (Tier-1, 2 and Tier-3 Network).

• 4G RF and Backhaul Network Systems, Microwave Planning & Design Complex TDM-IP-based Radio Systems Update and Upgrade of Point-to-Point (PP) Fixed Networks and Point-to-Multipoint (PMP) at Licensed Microwave Bands (11, 18, 23 GHz) & Unlicensed Microwave (5.8, 5.4, 24) Networks that connect 4G Base Stations to a Microwave Hubs and WiMax (Fixed & Point –to-multipoint), to a Wire line Network based on Fiber and IP technology. LAN, WAN and WLAN configuration, Cisco Routers, Switches & Alcatel-Lucent 7450, Carrier Ethernet Switch Routers, MW Packet Radio Alcatel-Lucent 9500, Dragonwave, Constellation-TRuepoint 5000, NEC, TOSHIBA Radios, also Andrew & RCA Parabolic Dish Antennas. Designed Backhaul Network using Microwave Propagation Models, Crane & Vigants/Barnett Fading Algorithms at average end-to-end Link availability is 99.999% from 2G/4G sites to Fiber Hub sites. Individual Hop Propagation availability objective is 99.9999%.

• Designed RF Propagation Models: GSM for AT&T Wireless Seattle, WA and CDMA2000 for Cricket Communication, Washington, DC. Planet EV 4.1 used for Model Tuning of CDMA2000 & Run Prediction also using the Agilent Receiver E6450, Agilent Software E6474A, Berkeley Transmitter, Grason Spectrum Tracker for CW Test. Sites Design & Analysis. Link Budget Analysis, POPS Analysis, and Load Balancing for entire Network. System. Dimensioning for Coverage & Capacity and multimedia Traffic Engineering.

• Designed Frequency Planning (TDMA_GSM Spectrum Clearing, 850 MHz and 1900 MHz, Frequency Plans for Los Angeles, CA Market AT&T Wireless Network) and related activities in a GSM rollout.

• Designed (E-OTD for E-911) Network, 270 LMU Sites of Portland, OR downtown area for AT&T Wireless,.(PCS-1900 MHz GSM based)

• Designed In-building Antenna Systems, Bidirectional amplifier, Splitter also Cellular and Powerwave products, used to extend Cellular, Two-way service, 802.11 also paging systems. Designed RFDS and layouts, site drawing review used Microsoft Visio

• Working Knowledge of ION-B Radio-over-Fiber Distributed Antenna system & ION-M High Power-density Fiber-based Distributed antenna system

• Designed Radio Sites for Ericsson Equipment RBS 2106, 2206, 2303, 2308 & 3106, 3206, 3303 3106 HcHc for UMTS (HSDPA) also Ericsson RBS 3206 High Capacity Indoor Macro and 3106 High Capacity Outdoor Macro RBS for W-CDMA Wireless Network. Designed RFDS & Site drawing used Visio for the San Francisco, CA Market for Cingular Wireless

• Designed Plumbing Diagrams for Ericsson Equipment & create Antennas Configuration with Feeders Lines directly from Ericsson Cabinet RBS 2308 micro sites, RBS 3106, 3206, 3303 to the Antenna through Diplexers & Duplexers Working with RAN features in UMTS

• Performed GSM Optimization (Nokia Equipment). Traffic performance statistics and alarms obtained from the switch, also Nokia OSS applications with radio network Optimization

• Designed Site Candidate Evaluation (Search Ring), Calculate Free Space Path Loss, Link budget, Earth Bulg & Interference Analysis, also

• LOS Analysis & Fade Margin Calculation

• TDM,IP/MPLS/Ethernet Radios, Design & Implementation with LAN, WAN, WLAN, & WWAN: Ethernet, 100BaseT,Frame Relay, SONET/SDH, T-1Transport, Leased lines, Hybrid Fiber Coax & DWDM amplified systems.

• Cisco Network Design Software & Tools used: Cisco Network Designer, Cisco Config: Maker, IP Subnet Calculator, Cisco Router Sim

• RF Measurement Tools: Spectrum Analyzer, Network Analyzers, Digital real-time Oscilloscope, Power meter

• Network/Telecomm Devices used: Cisco Routers (2500,2600,3600), Cisco Catalyst Switches (2900, 3500, 4000), 3COM LAN Switches/Hubs, ATM Switch, Frame Relay Switch CSU, Alcatel-Lucent 7450,9500 Carrier Ethernet Switch Router

Nokia, Fiber Optic, OC-3, OC-48, DLCs (Ericsson), Cross-connects.

• Radio Network Integration and Construction Management. Walks for Site Construction. Managed scheduled Deployments, Construction Crews and Venders also Network Integration. Co-ordinate Site Development for Site Modifications and New Site builds Co-ordinate Engineering, Zoning and Construction for New Site builds. Provided licensing assistance to other Venders; prepares requests for Frequency Coordination & Licensed Applications, FCC license renewal, and interprets FCC regulations

• Technical & Administrative support to the High Power AM Radio Broadcast Transmitters. Analyzed system and specifications, responsible for the Maintenance & Operation of Radio Broadcast Transmitter, UHF/VHF & HF Radio Navigation Systems & Space Diversity Systems, Mobile sets, Control room, Feeder lines, Multiplex equipment, Power plants (Diesel- Engine Generator) & its associated plants

• Bill of Material (BOM) preparation, and updating Xpercomm provisioning software to keep accurate record

• Prepared FCC license applications: provided licensing assistance to other venders; prepares requests for Frequency Coordination & Licensed Applications, FCC license renewal, and interprets FCC regulations

• Experienced with Quality Management and Quality Control systems, such as ISO 9001

• Languages: - C++, ASP.NET, SQL, National Instruments LabVIEW

• Proficient with Microsoft Word, Excel, Project, PowerPoint and Visio software programs to a level of professional proficiency

• Engineering Applications: PSpice, AutoCAD 2000, using ANSI Y 14.5 standards & protocols, Visio, PCBCAD tools and ORCAD.

Contact this candidate