Piping Designer

** – **** Wentworth Ave. SW Page *of *

Calgary, AB. CANADA

adbrsa@r.postjobfree.com

cell: 587-***-****

ASHLEI ILINCUTA

POSITION: Piping drafting and/or designing

SUMMARY OF QUALIFICATIONS

Piping Designer with piping experience in designing, drafting and detailing

Plant Layout using Aveva 3D Plant Design Management System (PDMS) and associated Design Modules

Plant Layout using Intergraph 3 D Plant Design System (PDS) Piping, Equipment Modeling, Drawing Manager and Smart Plant Reviewer

Intergraph SmartPlant 3D (SP3D) and CADWorx - Piping and Isometric extraction

Isometric drawing creation using PDMS, PDS, MicroStation and SP3D

Proficient with NavisWorks Reviewer

General Arrangement Drawing Production using PDS and SP3D

Production of Plot Plans, Key Plans and Detail drawings using MicroStation

Proficient in MicroStation / AutoCAD

Sound knowledge of industry or regulatory standards and codes as required for piping design

Analytical ability, flexible, thorough, professional, excellent communicator

EDUCATION

Intergraph 1997

Certificate PDS Piping / Equipment Modeling

S.A.I.T. 1997-1998

Process Piping Drafting I

Process Piping Drafting II

S.A.I.T. 1996

CADD Operator Certificate Program

The University of Calgary 1990-1996

Bachelor of Arts, Humanities

PROFESSIONAL EXPERIENCE

Jacobs Canada Inc., Calgary, Alberta, Canada 2001-2015

Piping Designer

Shell Carmon Creek SAGD Project (Aug. 2013-Feb. 2015)

Modeling of Distribution and Gathering Pipelines using PDMS

Implementing stress comments and support placements for trunk pipelines as well as laterals going to various Pads

Ashlei Ilincuta Page 2 of 3

Athabasca Oil Corporation Hangingstone SAGD (Jan. 2012-Jul. 2013)

Completed several layouts in various equipment modules using PDS

Produced 2D layout drawings, Stress and IFC Isometrics as well as GT Isometrics

Coordinated and collaborated with designers in Denver, USA, as well as Mumbai, India offices

Performed several yellow-offs and prepared the models for 30, 60 and 90% reviews

Worked on RFIs and Rev. 1 isometrics, including modeling of changes, P&ID mark-ups and coordination with other disciplines

CNRL Kirby (South) SAGD (Oct. 2009-Dec. 2012)

During EDS, modelled various equipment pieces using PDS ( pumps, glycol heater, drums, air cooler, air receiver, air dryers and compressors, etc.)

Layout of the Sales Oil Pumps as well as the Tank Bottom/Off Spec Oil Pumps

Successfully completed 30% Client Model Reviews for the Tank Area

For the Glycol Cooler Area, modeled the Cooler, associated piping, sent all lines to stress and implemented stress comments

Produced IFC Isometrics on various areas, on module, and stick built

Suncor Firebag Stage 3 SAGD (Oct. 2008-Jan. 2009)

Made revisions to piping in SP3D models to finalize design in Chemical

Injection Building of Diluent Stripping Unit

Extracted and submitted IFC isometrics for checking

Backdrafted checker’s comments in the model and Issued For Construction isos

BA Energy – Heartland Upgrader Project (Jan. 2005-Sept. 2008)

Detailed Design of 2 level Piperack consisting of 4 modules in Utility Area

Attended 60% Model Reviews with all other disciplines, Client and Construction team members

Issued For Construction all isometrics related to 4 PDS Models

Revised piping layout and supports in stick built Water Treatment Area

Coordinated with other disciplines, marked up vendor drawings

Issued Fabrication Isometrics for entire SB Area

Saudi Aramco – Hawiyah NGL Recovery Plant

Produced initial plot plan, site plan and related MicroStation piping drawings.

Created and Drafted P&IDs.

Modeled (PDS) all headers, stress loops and associated branches on the utility level of the main pipe rack.

Routed and modeled all piping around the gas heat exchangers and modeled associated platforms and stairs.

Exxon Mobil - LaBarge Acid Gas Injection

Revised piping layouts on PSV platforms and modeled all PSV ‘s and flaring system according to Vendor drawings

Responsible for a complete piping model and Issued all check prints

Backdrafted isometrics and issued IFC prints for all piping in this model

Ashlei Ilincuta Page 3 of 3

Modeled and routed various piping in the Acid Compressor Building

Syncrude UE-1 Project

Modeled equipment including exchangers, pumps, and drums

Responsible for the drafting and updating of all piping plans related to the 7-3 Area. These plot plans, module plans, underground piping DWG’s etc. were initially MicroStation drawings and later were redone entirely by extracting the information out of the PDS models using the Drawing Manager package.

Routed all piping related to two pumps within the exchanger structure

Revised various piping and nozzle relocations on vessels as design progressed

Issued check prints and backdrafted isometrics

Aided various senior designers in issuing the piping in their areas as IFC prints.

SNC- Lavalin Inc., Calgary, Alberta, Canada 1997- 2001

Junior / Intermediate Piping Designer / Draftsperson

Syncrude Canada Ltd. – Upgrading Debottleneck II (Vacuum Distillation Unit)

Initially drafted P&ID’s using MicroStation, then performed drafting of P&ID’s using PDS, drafted and revised 2D Isometrics and Piping Arrangement drawings

Produced as built drawings for Debottleneck I (DB I)

Edited PDS models to correct errors and corrupted elements

Implemented all the piping changes in the DB I PDS models to reflect As Built ISO’s

Generated PDS As Built isometrics using the Isogen Package

Modeled Utility Stations with Steam Traps at grade and on platforms & related piping

Produced Fabrication isometrics for the Vacuum Distillation Unit

Husky Oil – Lloydminster Upgrader Expansion FEED

Piping layout and spacing on the rack including stress loops

Modeled tie-ins of the ISPL rack with an existing rack

Produced pipe rack GA drawings, module key plan and model key plan drawings using the Drawing Manager PDS package

Process and utility transpositions and pipe rack sections using MicroStation

PERSONAL

Excellent communication skills (interpersonal and written) and proven ability to collaborate with team members in a multi-disciplined environment.

Strong organizational skills, technical competence and strong attention to detail.

Fluency in one additional language.

High level of adaptability, strong desire to succeed

REFERENCES WILL BE PROVIDED UPON REQUEST

Contact this candidate