DOMINICK VEGA

*** ****** ******, *******, ** ****3 Primary # Cell 541-***-**** Home # 631-***-****

Summary

Performed electrical, mechanical, pneumatic system integration checks and tool calibrations. Serviced AC/DC Stepper & Servo Motors, familiar with power supplies, vacuum pumps, dial calipers, micrometers, logic probes, volt ohm meters, amp probes, & bubble levels, repaired sensors - performed software revisions - used robot teach pendant and experienced in clean room protocols. Allen Bradley PLC ladder logic online training & worked on PLC installs requiring limited program runs against checksum error faults. Example such as a fault handling error so as not to allow the PLC to go into stop mode which may require writing a new code.

PROFESSIONAL EXPERIENCE

Orbital ATK (Donatech Engineering) – Instrumentation Technician 01/2016 – 05/2016

Assembled multi-layer electrical cabinets, PLC electrical controller boxes, labelled wires, assembled and tested 200 thermal couplers, ran heating tape and insulated pipes carrying temperature sensitive gases. Used knock out tool to clear wire run to junction boxes. Mounted signal alarm light towers. Assisted with bending pipe, explosive gas chemical leak detection at check valves, ran electrical lines and connected to network

Zebra Technologies (Premier Systems) – Mechanical Engineering Technician 9/28/15 – 1/19/16

Collected, delivered, and archive test data consistently and accurately to provide documentation of events and status. Evaluated mechanical environmental testing of scanner consumer products and documented. Participated, planned and coordinated tasks schedules, and performed preventative maintenance during downtime. Set up, adjusted and operated testing equipment as directed, by defined procedures. Monitored equipment performance, tests progress, troubleshoot and diagnosed typical problems with processes and equipment under direction, or following documented methods or procedures. Validated test parameters, equipment calibrations, identified failures, adjusted and repaired equipment

Global Foundries Contractor (Accretech America) 03/2015 – 06/2015 Prober Customer Engineer

Supported wafer processing installations tools. Adjusted continuity contact pins on wafer probers. Integrated systems consisting of robot handler, wafer docking load ports, robot transport, GUI interface. Prober needle inspects die at high speed and pin point accuracy. Verified continuity of electrical connections and confirmed Optical measurements were recorded, lubricated linear rails, adjusted encoder belts, sync stepper motors for correct pulse counts. Adjusted cameras for visual coverage of stage X & Y travel. Drove action items and punch list issues that were minor concerns

Global Foundries Semiconductor: 07/2014 – 01/2015 Equipment engineering Metrology tools.

Reviewed collected data for failure analysis, worked with 3 Sigma charts, validated control limits were within specification for random variations. Worked on software upgrades and set working parameters for pick and place robotics. Troubleshoot card racks and swapped out boards. Adjusted placement sensors, and level load port docking stations in a Class 10 clean room.

Aerotek Contract Engineering: Standard Motors, LI, NY. Electrical Mechanical Technician – 06/2014

Installed mechanical assemblies and integrated electrical wiring on panels with use of schematics. Inspected and tested optical sensors, used wire gauges from 14 to 22 for installations of transformers, cooling fans, circuit breakers, terminal blocks and grounds. Used low voltage power supply to drive Stand Motors test fixtures.

Technical Staffing Associates (TSA) Contract Mechanical Field Service Technician 03/2014 – 05/2014

Managed paper flow operations on MB Auto set 18 and MB Auto set XT – Set working parameters as needed to monitor paper flow operations. Recovered errors and performed preventative maintenance services

Joseph Machine Company: Field Service factory support technician 07/2013 - 10/2013 Dillsburg, PA

Populated electrical control panels (din rails) Proof read electrical / blue prints to lay out blank templates, verified installed components and red line corrections. Calibrated servo amplifiers (condition for proper frequency efficiency) Tested Allen Bradley contactors, thermal magnetic overload protection devices, installed trio programmable logic controllers (24volt DC) and set up Ethernet communication. Configured Acme transformers and set up phase according to load conditions. Specification 3 phase 480 volts 600 VAC rating for wiring; built custom engineering control panels per customer specifications to maximize HMI (Human Machine Interface). Daisy loop modules and terminated with resistive load. Installed variable frequency drives, worked with Trio PLC. Travel to sites for corrective action, implemented software up - grades, ran product to collect statistical process control data. Tested wiring for opens with DVM.

Field Service Engineer Intel D1C [NSTAR Global Services] 07/2012 – 11/2012 Hillsboro, Oregon Integrated electrical, mechanical, pneumatic TDK load ports on 300mm Plasma Edge Bevel multiple chamber tool (Semiconductor class 10 clean room) Trouble-shot equipment using DVM’s and Oscilloscopes to validate and calibrate test point voltages per schematics

Aerotek Contract Engineering (Voltaix Corporation) Branchburg, NJ 08876 02/2011 – 03/2011

Electrical- Electronics-mechanical technician

Calibrated and triggered residual gas analyzers to detect Boron Trifluoride, Di borne, Germanium & Silicon. Inspected and calibrated 10 analyzers per day on a daily rotation for correct gas configuration, filtration wear, battery levels, false signals, proper calibration stickers. Broke lines in confine spaces to inspect proper operations of manometers & verified that pressure readings reflected a secondary manometer as the tool was out gassed from corrosive & explosive gasses while using gas analyzers to detect excess exposure to chemicals.

Dawned scuba gear as an independent breathing source of air. Inspected O-ring seals, used Helium leak detector. Calibrated chemical monitoring detectors, adjusted mass flow controllers, monitor alarm logs, calibrated weight scales prior to mixing sample chemicals. Verified current and voltage settings by use of VOM and amp probes

Telstar Corporation – Bristol, Pa 19007 05/2009 Mechanical technician

Built mechanical assemblies per blue prints

Semitool: Customer Support Engineer, 12/2007 - 11/2008 Reduction in workforce

Supported ANADIGICS (Gallium Arsenide Fab.) Flow pumps, filled sensors, inspected contact rings, spray solvent tools, Raider ECD, maintained pH levels to stabilized process chemistries

Electrode Chemical Deposition Tools

Daifuku America: Field Engineer Intel, 11/2004 - 02/2006 (Contract Position)

Supported 300mm AMHS for wafers and reticule storage (Intel Corporation) Managed OHTV Supervisory Master Controller-Pick & Place operations Performed electrical, mechanical, and integrity checks of robust software

Improved up time through preventative maintenance & tool modifications Robot Calibrations within Stocker Track WIP on monorails for Copper & Non-Copper process tool Used Material Control Systems for documentation & tool trends Trouble-shot and calibration of various equipment using DVM’s, Oscilloscopes and Spectrometer

KLA-TENCOR Corporation, Milpitas, Ca

Customer Support Engineer (2000-2001)

Provided support services for automated metrology wafer processing tool installations. Strengthened customer loyalty and increased sales by delivering acceptable time-lines

Supported service contracts, maintained consumables & provided training for end users.

Adjusted lasers, sensors, travel axis, and calibrated indexers.

Surfscan 6200, Surfscan 6220, Quantox non-contact measuring tool

Microchip Plant Closure Puyallup, WA RIF (semiconductor downturn)

NIKON MICROELECTRONICS SYSTEMS DIVISION

Field Service Representative Melville, New York (1999- 2000) Recruited by KLA

Tailored support for personalized availability, and effective problem solving.

Interviewed users, researched, and recommended solutions for engineering evaluations.

Streamline timelines for customers to reduce cost of ownership. Confirmed tool footprints and expenditures prior to installs. Calibrated inspecting tools for optimal bright / dark field defect detection. Reviewed ongoing equipment performance, coordinated with R & D to develop robust user software.

HYUNDAI SEMICONDUCTOR AMERICA

Equipment Engineering Technician - Eugene, OR (1996 - 1998)

Ramp up of 200mm DRAM production facility. Facilitated installation, maintenance,

And process data to monitor production trends. Perform preventative measures to effectively exceed MTTR and MTBF for production output.

Measured, aligned, and calibrated laser output power specifications, performed RF calibrations for Mattson Aspen II. Routine wet cleans on AMAT 5200, Tel Unity DD, Tel Unity ATC, & PSK barrel etchers. Monitor wafers for contamination concerns.

(Recession in Global DRAM Market) Plant shutdown moved operation to Korea

THRIFTY ELECTRONICS

Equipment Maintenance Technician Los Angeles, CA (1989 - 1995)

Managed microprocessor control photofinishing equipment, calibrated mechanical, electrical, and pneumatic systems. Refurbished chemical pumps and maintained mechanical overhaul adjustments of integrated servo and stepper motors. Component level root cause analysis to curtail budget expenditures of excess parts.

Upgraded fiber optics and adjusted open and close loop sensor outputs. Organized spare parts inventories of high use critical spares, and evaluated new software and hardware changes per Engineering Change Orders. Utilized blue prints, and electrical schematics.

Plant shutdown (Corporate Merger with competitor)

United States Marine Corps Honorable Discharge

EDUCATION:

ITT TECHNICAL INSTITUTE

Bachelor of Applied Science Degree (Automated Manufacturing) GPA 3.25

Associate of Applied Science Degree (Electronic Engineering) GPA 3.75

Perfect Attendance Award for two years (Honors Graduate)

Bucks County Community College Electrical and Solar Certificates

PLC training Buck County Community College A-B SLC-500 / rslogix 500

Contact this candidate