Welding Inspector
Resume:
RESUME
Name
Permanent Address
Current Address
Phone No.
Hanafi bin Hassan
**, ***** **** ******* *, Bandar Baru UDA, 81200,
Johor Bahru, Johor, Malaysia
Lot 47, Taman Perumahan Rancha Rancha, 87000, Wilayah Persekutuan Labuan
acti3i@r.postjobfree.com
NRIC : 820***-**-****.
Age : 33 years old.
Sex : Male.
Date of Birth : 09 September 1982.
Place of Birth : Johor Bahru, Johor.
Religion : Muslim.
Nationality : Malaysian.
Marital Status : Married.
Passport No. : A36355120 (Valid until : 27 Nov 2020)
Seaman No. : 201********* (Valid until : 29 Nov 2020)
Language : Bahasa Malaysia (fluent) and English (fluent).
Expected Salary : Negotiable
EDUCATION
Qualification : BTEC Higher National Diploma
Field of Study : Mechanical Engineering
Institute : International University College of Technology TWINTECH
(Twinning with University of Wales)
CGPA : 3.08 / 4
Graduation : 2005
Qualification : Vocational Certificate
Field of Study : Mechatronic Engineering Technology
Institute : MARA Vocational Institute, Malaysia
CGPA : 2.81/4
Graduation : 2002
CERTIFICATION & QUALIFICATION
American Welding Society, Certified Welding Inspector (AWS-CWI)
Certification No. : 10071481
Year Obtained : 2009
Expiration Date : 1 July 2016
Ultrasonic Testing PCN level 2
Certification No. : F010S3321783
Categories : 3.1 3.8 3.9 v
Expiration Date : 3 January 2016
BASIC OFFSHORE SAFETY INDUCTION & EMERGENCY TRAINING – BOSIET/OPITO
Log Book No. : MY 068557
Certificate No. : 007*-****-**** 1228 8293
Expiration Date : 24 July 2016
SEMINAR & COURSE ATTENDED
Confined Space Rescue
Date : 2007
Venue : Johor Skill Development Centre (PUSPATRI)
Authorised Gas Tester
Date : 2007
Venue : Johor Skill Development Centre (PUSPATRI)
American Welding Society, Welding Inspection and Technology
Date : 2009
Venue : SIRIM BERHAD
CSWIP Radiographic Interpretation 3.4
Date : 2010
Venue : CIDB-TWI
Ultrasonic Testing Course (NDT-UT2)
Date : 2010
Venue : Johor Skill Development Centre (PUSPATRI)
PPG PMC Blasting & Painting Presentation
Date : 2010
Venue : Kencana Torsco Sdn. Bhd.
WORKING EXPERIENCES
PIONEER ENGINEERING SDN. BHD.:2 Nov 2015 ~ Present
Position : Piping Inspector – On board Repsol KNDP-Alpha Platform, Sabah, Malaysia
Responsibility:
1)To review and understand the piping & equipment layout on each level of the platform deck prior to start of the line checking work.
2)To identify the piping & instrumentation identification & location of each line by referring to P&ID’s. The task given are to identify the modified line & to sketch as built isometric drawing as per actual piping line condition & requirements due to missing of isometric drawing by previous platform operator.
3)Check & verify the actual piping & instrumentation at each deck of the platform whether it is identical with the P&ID’s.
4)To sketch an isometric drawing of the actual modified piping line on each platform deck & submit it to the engineer & drafter before submission to Repsol Engineering Team. The sketched piping line isometric drawing should include the following information:-
a)Location (platform, deck name, process skid identification)
b)Module number
c)Line number in full including all insulation codes
d)Direction of North (always pointing top left in the drawing)
e)Date of creation
f)Deck, bulkhead, grating & floor penetration
g)Piping supports
h)Access requirements (ladder, scaffolding or absailer)
i)Pipework diameters
j)Pipework specification changes
k)Pipe features base on length for NDT (1 test point per 1 meter of straight pipework & fitting)
l)Inspector initial or drawn by info.
m)Start & finish of pipework (a “from” & “to”)
n)P&ID reference
o)Instrumentation & equipment tag number such as valves, pumps, skids, vessels etc.
p)Direction of flow
q)Extend of insulation
r)Dead leg number
s)Weld number
FMC WELLHEAD EQUIPMENT SDN. BHD.:9 Sept 2013 ~ August 2015
Position: Mechanical QC inspector MPS (Manifold Piping System/Subsea Control & Data Management)
Responsibility:
5)To review and understand (approved if necessary) all related documents before start the project (ITP/Procedure/Drawing/DBI (Data base information)/WPS/PQR / Welding certificate and vendor related document).
6)Verify and review certificate of base material & welding consumable materials confirm that material meet specification requirements, To ensure specified consumables are used in conjunction with the appropriate base material(s) or combination thereof as per WPS range.
7)Witness performance and testing of procedure qualification weld tests, and to verify these activities when performed by outside agencies.
8)Verify that welders, welding operators, and tackers have been properly qualified in accordance with the applicable codes, standards or other documentation and that their qualifications permit them to use the welding procedures specified for their work.
9)Witness performance and testing of welder and welding operator qualification weld tests. May also be required to verify these activities when performed by other agencies.
10)Monitor that the specified consumables are used and that the consumables are maintained in the proper manner / condition, per specification requirements or as recommended by the manufacturer.
11)Prepare Report and verify correct fit-up, joint preparation & surface finish meets the approved FMC DBI &Drawing and applicable code specification or standard.
12)To verify and perform dimensional verification before start welding to ensure all dimension within tolerance as per drawing requirement.
13)Monitor and randomly cross check proper pre-heat and inter-pass temperature is maintained as required per the Approved WPS.
14)To monitor welding activities and review welding check list every each visit to ensure the welder are welding as per WPS requirement.
15)To perform baroscopic inspection using High definition baroscopic equipment on the pipe ID for inspects root penetration as per acceptance criteria in specification before proceed to next step filling and capping .(Client spec, DEP spec, FMC spec and international standard)
16)To perform Welding inspection as per specification requirement.(Client spec, DEP spec, FMC spec and international standard)
17)To request and review PWHT chart/report and to ensure all data heating time/ temperature, soaking time/ temperature meeting WPS and Material requirement, if required.
18)To verify and perform final dimensional verification after welding/machining and ensure all dimension within tolerance as per drawing requirement.
19)Perform piping Line Check and prepare punchlist then consult punch work with subcontractor as follows:-
• Assure that all pipe supports are properly installed of correct type and material.
• Follow up and perform back check of Punch Work.
• Prepare field materials requisitions for permanent plant materials which mainly affect punch clearing.
• Supervise and control punch clearing groups.
• Prepare progress report of punch cleared test packages for hydrotesting.
• Perform piping reinstatement check.
• Responsible for preparing as-built drawing of modified lines as per site actual condition requirements and take the approval from Design Engineering Section.
20)To request and witness related NDE (RT, CR, UT, PAUT, TOFD, MT, and PT) as required per Codes, DBI and specification.
21)To verify radiography film and ensure all indication, sensitivity, UG, identification and density recorded as per client/FMC spec. and international code.
22)To request and perform hardness test and ensure the welding and material meet the requirement.
23)To attend, liaise, entertain and meeting with customer/vendor for document review, film interpretation and inspection.
24)Witness and verify hydro testing,gas test and electrical test to ensure meeting requirement as per TST/PSM procedure and specification.
25)To raise NCR/CAR/QN if have deviation during process/defect/dimension out of tolerance from specification, code and specific requirement.
26)To prepare/review and endorse all necessary document and report as per requirement and compile in MRB.
27)Review and endorse MRB and ensure meet the client requirement before submit to Customer for final approval.
EXTENDED FACTORY ACCEPTANCE TEST (E-FAT)
Also involve in Shell Extended Factory Acceptance (E-FAT) for 13 3/8” Enhancement Vertical Deepwater Tree (EVDT).
Witnessing and monitoring assembled on 13 3/8” Tubing Hanger.
Witnessing and monitoring assembled on 18 ” and 10” Torus 4 Connector
Witnessing and monitoring FAT on Emergency Disconnect Package
Witnessing and monitoring FAT on Lower Riser Package
Witnessing and monitoring assembled on model 3000 valve.
Witnessing and monitoring assembled on Tubing Head Spool.
Witnessing and monitoring assembled and FAT on 13 3/8” EVDT system
Witnessing and monitoring assembled and interface test for Mechanical tree running tool
Witnessing and monitoring assembled and interface test for Tree Mechanical Release tool.
Witnessing and monitoring assembled and interface test for THD running tool.
Witnessing and monitoring assembled and interface test for 13 3/8” Tubing Hanger R/R tool.
Witnessing and monitoring assembled on ROV receptacles.
Witnessing and monitoring interface test multiple quick connect.
Witnessing and monitoring interface test on Subsea Control Module
Witnessing and monitoring FAT on Halliburton test plug into Tubing Hanger.
1) TOTAL CLOV– Piping & Tubing Weldment for XT, Manifold, UDM, Jumper Torus Connector (FMC Nusa Jaya – Johor)
Client : TOTAL E&P.
Code : Q-SPEC/ASME B31.3 (Process Piping) NORSOK L-CR-001 / NORSOK M- 601 (Welding & Inspection of Piping / NORSOK M101 (Steel Structure Fabrication)
Material : UNS31603 (316L), UNS 31600 (316), UNS 30400 (304), UNS 32760 (S. Duplex)
Year Built : 2013
2) GUMUSUT KAKAP Phase 2 Umbilical Termination Head & XT – Tubing Weldment & Testing (FMC Labuan Base)
Client : SHELL SABAH PETROLEUM CO.
Code : Q-SPEC / ASME B31.3 (Process Piping) / SDS-US-56 Rev. 1 / NORSOK L-CR-001 / NORSOK M-601 (Welding & Inspection of Piping) / NORSOK M101 (Steel Structure Fabrication)
Material : UNS 31603 (316L), UNS 31803 (Duplex), UNS 32760 (S. Duplex)
Year Built : 2015
DAEWOO INTERNATIONAL E&P.:28 Feb 2013 ~ 25 June 2013 On-board HD 60
Position: Subsea HUC Lead Inspector (SHWE Project – Offshore Sittwe, Myanmar)
Responsibility:
1) Representing companies during Daewoo offshore Subsea HUC campaign for SHWE project to ensure all specifications and guidelines along with company’s scope of work is followed.
2) Witness & verifying MYA-N Umbilical Line 3 Leaks Rectification & Subsea HUC activities & review documentation as details below:-
Recovery of Umbilical Termination Assembly (UTA) for HP1 (Line 3) leaks repair.
Re-torqueing of HP1 (Line 3) hose fitting.
Post UTA Re-torqueing for HP (Line 3) pressure testing (Pressure test after leaks repair)
Post UTA to UDM integration pressure testing (11000 psi/1 hour).(Pressure test after UTA installed to Umbilical Distribution Module (UDM) connected to Topside Umbilical Termination Unit (TUTU)
14” pipeline dewatering (manifold to riser), gauging & N2 inerting & leak test with KAMOS gasket.
HFL & EFL (Hydraulic & Electrical Flying Leads) installation & testing.
Monitor electrical continuity check perform by the contractor prior to installation of EFL.
NAS cleanliness rating check for Oceanic HW443R fluids during line flushing.
Manifold’s (4 slot,1 spare) 14’’,6’’ & 2’’ Valve function test (OTP) & pre-commissioning.
3) MND-A,B,C & D Well head valve function test (OTP). The test consists of Open/Close operation for the valve as list below :-
SCSSV (Surface Controlled Subsurface Safety Valve)
AAV (Annulus Access Valve)
AMV (Annulus Master Valve)
PMV (Production Master Valve)
XOV (Crossover Valve)
CIV 1,2 & 3 (Chemical Injection Valve 1,2 & 3)
PCV (Production Choke Valve)
4) Review report & commissioning documentation before handover to operations team. The documentation should consist of:-
Completion acceptance certificate (signed by both parties).
OTP for each function test activities.
ROV & Diver monitoring records for subsea As-built.(DVD)
5) Ensure & verifying all lifting apparatus such as lifting crane, shackle, turnbuckles, slings, pad eyes certificate are valid before contractor performing any heavy lifting job.
Project Involved
1) SHWE MYA-N Umbilical Line 3 Leaks Rectification & Subsea Hook up & Commissioning for SHWE project (Bay of Bengal, Offshore Myanmar)
Owner : DAEWOO INTERNATIONAL E&P
Code : ISO 13628-5:2009 Petroleum & Natural Gas Industries – Design & Operation of Subsea Production
System. Part 5 – Umbilical.
Year Built : 2013
PETROFAC MALAYSIA LTD.:15 MARCH 2012 ~ 23 Feb 2013
Position: General Inspector (Cendor Phase II & West Desaru Steel Catenary Riser’s,PLET’s, Midwater Arch & Gravity Base Package fabricated at Labuan Shipyard & Engineering,Labuan,Malaysia)
Responsibility:
1) Performed Surveillances Inspection for Fabrication & Testing for Cendor & West Desaru PLET/MWA Packages at Labuan Shipyard & Engineering Sdn. Bhd.
2) Observe & Expedite project progress to meet Load out date for each package.
3) Observe sub-contractor work quality & progress with provision of Wellstream International Limited (Contractor)
4) Witness FAT activities consists of :-
Hydrotest for riser and pipe joints
Pneumatic test for Mid Water Arch (Holding time 4 hour,4.5 Bar of N2 for MWAs buoyancy segment)
5) Raised Non-conformance records for any non-conformance finding during fabrication & testing activities
6) Observed safety rules to be followed by all shop floor personnel.
7) Perform piping Line Check and prepare punchlist then consult punch work with subcontractor as follows:-
Assure that all pipe supports are properly installed of correct type and material.
Follow up and perform back check of Punch Work.
Prepare field materials requisitions for permanent plant materials which mainly affect punch clearing.
Supervise and control punch clearing groups.
Prepare progress report of punch cleared test packages for hydrotesting.
Perform piping reinstatement check.
Responsible for preparing as-built drawing of modified lines as per site actual condition requirements and take the approval from Design Engineering Section.
8) Sign off final MDR prior to package load out.
9) Witness & perform inspection during load out with Marine Warranty Surveyor representative prior to load out of each package. Inspection during load out consists of:-
Review all lifting equipment certificate validity & condition before allowing any heavy lifting work.
Checking crane hardware such as pins (inner/outer boom pivot pins & retainers),bearing, shafts, rollers & locking device for wear, cracks, corrosion & distortion.
Checking the crane load hook for abnormal throat distance, twist, wear & cracks.
Checking the crane hydraulic system (hoses, tube & fittings) for leakage & proper oil level.
Checking the gear oil change in rotation drive system per maintenance schedule.
Review and verify load out contractor’s proposal for sea-fastening activities.
10) Witness & verify all HUC activities & review documentation as details below:-
NDE carried out.
Welding procedures.
Removal of all items subject to damage during flushing, cleaning and pressure testing.
Flushing of pipework.
Chemical cleaning and testing of pipework.
Drying of tested pipework.
Preservation of tested pipework.
Reinstatement of all items after testing.
Final inspection of pipework.
Test ISO's and P&ID's showing the extent of each pressure test.
Pneumatic and hydraulic tubing.
Hot oil flushing of pipework.
Bolt tensioning.
Pipe supports completed.
Insulation.
Flow coding
3) Review report & commissioning documentation before handover to operations team. The documentation should consist of:-
Completion acceptance certificate (signed by both parties).
Commissioning P&ID showing the extent of the completed system.
Authority certificates.
Operational procedures and handbooks
Project Involved
1) CENDOR FIELD DEVELOPMENT PHASE 2 & WEST DESARU – Steel Catenary Risers, PLET’s, Mid Water Arch, Processing Skid & Gravity Base (Labuan Shipyard & Engineering – Labuan)
Owner : PETROFAC MALAYSIA LIMITED
Code : AWS D1.1,ASME B31.4,API 1104
Material : API 5L X42, UNS 30400 (304), ABS EH32, UNS 31603 (316L)
Year Built : 2012
2) CENDOR FIELD DEVELOPMENT PHASE 2 & WEST DESARU – Installation of CDW-B & CDW-C Steel Risers, PLET’s, Mid Water Arch, Processing Skid & Gravity Base (PM304 field - Offshore Terengganu)
Owner : PETROFAC MALAYSIA LIMITED
Code : AWS D1.1,ASME B31.4,API 1104
Year Built : 2012
FMC WELLHEAD EQUIPMENT SDN. BHD.(Labuan Base).:1 Jun 2011 ~ 23 Feb 2012
Position: QC inspector MPS (Manifold Piping System/Subsea Control & Data Management)
Responsibility:
1) Responsible for weld & mechanical equipment inspection.
2) Witness WQT activities.
3) Ensure that the requirements for all weld, welder and welding activities are correctly specified and carried out in accordance with the relevant codes, client specifications (FMC DBI & SHELL DEP’s) and contract standards.
4) Perform SIT and FAT activities.
5) Perform Mechanical Unlock & Lock function for FMC Torus III connector for manifold & tree end kit
6) Monitor inclination lift for completed well jumper as per FMC procedure.
7) Perform test gasket & snorkel installation before hydrotest.
8) Perform 12 500 psi hydrotest for completed well jumper within 4 hour holding time.
9) Prepare HPU before hydrotest, inspect all related equipment such as pressure gauge, needle valve, pumps, coupling etc.
10) Monitor Torus III connector electrical continuity check perform by the contractor prior to installation
11) Ensure all lifting equipment such as shackle, turnbuckles, slings, pad eyes certificate are valid before contractor performing any lifting job.
12) Verify NAS (443 hydraulic fluid clean rating) are in required rate before performing any mechanical function on Torus III connector.
13) Perform welding monitoring & inspection for 5/8’’ super duplex SS tubing fabrication for FMC Control & Data Management dept.
14) Monitor mill surveillance during manufacturing and threading of casing, tubing and well conductors.
15) Perform inspection during manufacturing /refurbishment of surface/sub-sea wellhead and christmas tree, drilling risers and tools, downhole equipment.
16) Review material certificates and verify traceability
17) Ensure proper identification like tagging and marking
18) Ensure proper material handling, storage and preservation, segregation and packing
19) Monitor heat treatment and threading of end connection like API, Vam, NSCT, NSCC, etc
20) Witness laboratory testing like CTOD, PMI, hardness and NDE
21) Monitor repair on OCTG and completion equipment.
22) Witness hydro and gas testing on wellhead & X’mas tree
23) Witness fit function and stack up testing on wellhead & X’mas tree and downhole equipment
24) Compile material status report and inspection visit report
Project Involved
1) COPI BAWAL SUBSEA DEVELOPMENT Christmas Tree Flow Loop Piping - (FMC Nusa Jaya – Johor)
Client : CONOCO PHILIP
Code : FMC Q-SPEC/ASME B31.3 (Process Piping)
Material : Nickel Alloy 625 overlays
Year Built : 2012
2) GUMUSUT KAKAP Umbilical Termination Head – Tubing Weldment (FMC Nusa Jaya – Johor)
Client : SHELL SABAH PETROLEUM CO.
Code : Q-SPEC/ASME B31.3 (Process Piping)/SDS-US-56 Rev. 1
Material : UNS 31603 (316L)
Year Built : 2012
3) SHELL GUMUSUT KAKAP Well Jumper Fabrication & Testing (FMC Labuan Base)
(14 Unit of Well jumper)
Client : SHELL SABAH PETROLEUM CO.
Code : Q-SPEC / ASME B31.3 (Process Piping)/SDS-US-56 Rev. 1 / NORSOK L-CR-001 / NORSOK M-601 (Welding & Inspection of Piping) / NORSOK M101 (Steel Structure Fabrication)
Material : Nickel Alloy 625 overlays
Year Built : 2011
KENCANA PETROLEUM BHD.: 1 September 2010 ~ May 2011
Position: Mechanical/Piping Inspector
Responsibility:
1) Involve in Gorgon Pre-assembled Rack (PAR) Project, Fabrication of LNG Jetty & Marine Structures.
2) Obtained all relevant documents related to Project such as Client’s specification and International Codes, QA/QC related procedure, Inspection & Test Plan (ITP), AFC drawings and other approved procedure by client.
3) Perform material inspection on incoming material (Piping):
Review packing list document to ensure material/item need to be inspect.
Run visual inspection and quantity check to the item as per packing list to ensure all item had been packing same with state in packing list.
Ensure incoming material from manufacturer are in order and meet requirement and as per Delivery Order and Purchase Order.
Review Mill Certificate to ensure raw material information same with attached mill cert as per Client Specification (chemical composition + Inspection certificate).
Inspect internal and external condition (external packing, internal packaging, and material condition-rusty, bevel condition, seam weld, pipe ovality & etc).
4) Read and interpret engineering drawing, specification in soft or hard copy.
5) Capable to generate welding related procedure e.g. WPS, welding sequence, weld repair, visual inspection procedure and etc.
6) Train and educate the welders for achieve client satisfactory and promote good workmanship.
7) Conducting & performing QA/QC inspection such as:-
Material Verification Record prior cutting & fabrication.
Fit up / Visual inspections check upon fabrication stages complete.
Performed PMI on Stainless Steel pipe witnessed by SLC Inspector.
Surveillance check such as weld parameter and electrode control preheating to ensure complied with respective WPS & procedure.
Welding Procedure Qualification Test (WPQT) and Welder Qualification Test (WQT).
Blasting & Painting inspection, and insulation on Cryogenic Stainless Steel Pipe.
Hydrostatic Test, Pneumatic Test, Leak Test & Flushing Inspection.
Non-Destructive Testing (NDT) Inspection, which include Radiography Interpretation, Ultrasonic Test, Magnetic Particle Inspection & Dye Penetration Inspection.
8) Performed before hydro test & pneumatic test activities:
Carry out Line check / walk for all completed system and do the punch listing with Client.
Performed flushing activities prior conducting leak test (hydro & pneumatic test).
9) To review and verify Hydro & Pneumatic test Package requirement with;
Latest P & ID.
Latest modification mark-up in ISO Drawings.
Ensure WIS is tallied with the latest modification mark-up ISO drawings.
Punch list to be attached.
Pipe work check sheet to be filled.
Calibration certificates verified by client for pressure gauge and recorder.
Performed during hydro & pneumatic test activities;
Checked all equipment and tools are in place and installed properly.
To check and monitor pressure gauge during holding time and increasing gradually of the pressure, if any sign of leak.
Performed after hydro & pneumatic activities;
Prepare the hydro test report and check sheet, and submit to client for sign off.
Carry out blow dry activities and notify client to witness the activities.
10) Responsible for ensuring that adequate protection and preservation a given to equipment and stainless steel material to avoid contamination or corrosion during fabrication.
11) Perform routine checks to ensure workmanship practices are uniform and consistent throughout all aspects of steel work fabrication, verification and testing.
12) Review construction documentation for completeness and correctness.
13) Coordinate and monitor NDT activities for all spools and pipe installed.
14) Review and verify final NDE results.
15) Coordinate with subcontractor in all the NDT testing and inspection.
16) Ensure all the line pipe is fabricated in accordance with Specification and Standard requirement.
17) Ensuring that contractor production repair works are carried out in accordance to code, standard, procedures and client specifications.
18) Compile the final document and forwarded to the Higher Authorization.
18) Liaise with Client Representatives from SLC, KJV-G and third party.
Project Involved
1) Gorgon LNG Jetty and Marine Structures Project (Kencana Torsco Yard)
(23 Unit of Jetty Structure and Piping Nesting-Total Project Weight-20 000 Tonnes)
Client : SAIPEM LEIGHTON CONSORTIUM/KJV-G/CHEVRON
Code : AWS D1.1/ASME B31.3/ASME IX
Material : UNS31603 (316L), UNS 31600 (316), UNS 30400 (304)
Year Built : 2010
DYNAC SDN. BHD.: Nov 2005 ~ August 2010
Position: QA/QC Inspector (Welding/Mechanical)
Responsibility:
1) Ensuring all material and procedure are same as approved drawing by client accordance by client specification and by required code / standard before been approved for fabrication.
2) Monitoring and prepare WPS (Welding Procedure specification) for relevant project.
3) Monitoring and prepare WQT (Welding Qualification Test) activities.
4) Monitor and witness of Mechanical Test with Third Party & Client/Representative.
5) Arranging activities as per ITP (Inspection Test Plan).
6) Checking, recording and monitoring:-
Incoming material (plate, beam, pipe, fitting, etc) according to the Purchase. Order / Mill Certificates.
Material identification (heat no.) transfer witness by Third Party, DOSH, Client Representative or End User (if required).
Layout marking, cutting fit up and dimensional before start welding (beam, plate, pipe, etc).
Before, during and after welding activities.
Final Inspection (dimensional, orientation, elevation, straightness, roundness) before and after welding.
According total expansion rate after tube expansion activities (prepare expansion report).
Painting activities and surface profile for blasting.
7) Monitoring and arranging the NDE activities such as RT, UT, MT and PT.
8) Final Inspection with Third Party or Client / Representative.
9) Monitoring and witness PWHT (Post Weld Heat Treatment) activities and review chart.
10) Checking surface profile for blasting as per project specification.
11) Checking paint, thinner, weather humidity, WFT (Wet Film Thickness) and DFT (Dry Film Thickness) for painting activities (Review painting report).
12) Monitoring and witness of Hydrostatic Testing and Prepare the Hydrostatic Testing Certificate, Chart and Pressure Gauge/Recorder calibration Certificate.
13) Compiling the Manufacturing Data Record (MDR) and forwarded to the Higher Authorization.
Project Involved
1) Kinabalu Gas Processing Platform (KNPG)
Topside Structure fabricate by First Oil Engineering Sdn Bhd
Client : Petronas Carigali Sdn. Bhd (PCSB)
Code : AWS D1.1 2004
Year Built : 2010
2) E & I Building for Gumusut Kakap Semi-Submersible FPS Project
( 2 Unit E&I Structure c/w Instruments)
Client : SHELL / MISC / MMHE
Code : AWS D1.1
Year Built : 2010
3) Air Cooler Heat Exchanger (ACHE) for Duyong A,B & C Production Cooler
( 22 Bundles – Duplex and 316L material).
Client : PETRONAS CARIGALI SDN. BHD.
Code : ASME VIII Div.1 / AWS D1.1
Material : UNS 31603 (316L), UNS 31803 (Duplex)
Year Built : 2009
4) Air Cooler Heat Exchanger (ACHE) for F23 VLAP Compression Project
(12 Bundles – Duplex and 316L material).
Client : SHELL / PETRONAS CARIGALI SDN. BHD.
Code : ASME VIII Div.1 / AWS D1.1
Material : UNS 31603 (316L), UNS 31803 (Duplex)
Year Built : 2009
5) Steam Condenser for PSR II Revamp Project
(6 Bundles – C-MN, and 316L material).
Client : FOOSTER WHEELER E & C ( M ) SDN. BHD.
Code : ASME VIII Div.1 / AWS D1.1
Material : UNS 31603 (316L), C-Mn
Year Built : 2009
6) Air Cooler Heat Exchanger (ACHE) for Sumandak Phase II Dev.
(9 Bundles – C-MN, Duplex and 316L material).
Client : DYNAC / PETRONAS CARIGALI SDN. BHD.
Code : ASME VIII Div.1 / AWS D1.1
Material : UNS 31603 (316L), UNS 31803 (Duplex), C-Mn
Year Built : 2008
7) Petro prod FPSO Project. (12 units Shell & Tube – Carbon & Stainless Steel Material )
Client : GAS SERVICES INTERNATIONAL, SINGAPORE
Code : ASME VIII Div. 1
Material : UNS 31603 (316L), C-Mn
Year Built : 2008
8) Hot Oil Trim Cooler Package. (2 units Heat Exchanger - Carbon Material).
Client : TALISMAN, VIETNAM / SIME DARBY
Code : ASME VIII Div. 1 / U-Stamp
Year Built : 2008
9) Air Cooler Heat Exchanger (ACHE) for Chevron Thailand. (16 Bundles, Duplex)
Client : UNIVERSAL COMPRESSION INC. / CHEVRON THAILAND
Code : ASME VIII Div. 1 / U-Stamp / National Board (NBBI) / AWS D1.1
Material : UNS 31603 (316L), UNS 31803 (Duplex)
Year Built : 2008
10) Cascade Chinook FPSO Project (12 Units Shell & Tube – Carbon & Stainless Material).
Client : TECHNICS OFFSHORE ENG. PTE.LTD
Code : ASME VIII Div. 1 / U-Stamp
Material : UNS 31603 (316L)
Year Built : 2008
11) Vessel for Pinghu Oil & Gas Field Development Project. (3 units Shell & Tube - Duplex Material).
Client : SPC / CNOOC, CHINA
Code : ASME VIII Div. 1
Material : UNS 31803 (Duplex)
Year Built : 2007
12) Vessel for Dew
Contact this candidate