Dilip Ravindra

** * *** ** *** *** San Jose CA **113

acte38@r.postjobfree.com

+1-562-***-****

OBJECTIVE:

Seeking full time position in the field of embedded firmware/software development.

TECHNICAL SKILLS:

Proficient with C programming.

Good understanding of MATLAB, VHDL, GNU toolset

Hands on experience in using, ARM Cortex-M4, MSP430, Arduino Uno development boards.

Experience in using UART, SPI, I2C and ZigBee protocols.

Good knowledge of real time operating systems like FreeRTOS and TinyOS

Hands on experience in using PIR sensor, magnetometer, accelerometer.

Familiar in using Keil MDK, Code Composer Studio, Xilinx and Arduino IDEs..

Experience in using OPNET IT GURU academic edition and Cisco Packet Tracer for network design and simulation.

EDUCATION:

Master of Science (Electrical Engineering)

California State University Long Beach, Long Beach, California 08/2015

Jawaharlal Nehru National College of Engineering (Electronics and Communications)

Affiliated to Visveswaraya Technological University, Karnataka, India 01/2013

WORK EXPERIENCE:

Teaching Assistant at California State University Long Beach

Instructor for EE 301 Digital System Design / ET 442 Computer Circuits (Spring 2015 semester).

Lab instructor for EE 546 Advanced Microprocessors and Embedded Controllers II (Spring 2015 semester).

PUBLICATION:

Ying, K., Ameri, A., Trivedi, A., Ravindra D., Patel D., Mozumdar, M., "Decision Tree-based Machine Learning Algorithm for In-node Vehicle Classification", IEEE Green Energy and Systems Conference (IGESC 2015) (Accepted)

ACADEMIC PROJECTS:

Development of Micro Wireless Sensor platforms for collecting Data of passenger freight interactions (July 2014 - Present)

Interfaced PIR sensor with LPC1769.

Interfaced Honeywell’s HMC5883L Triple Axis Magnetometer with LPC1768, MSP430 development boards.

Designed I2C firmware to read the data from magnetometer

Designed an algorithm to classify the vehicles based on size using MATLAB and machine learning tool WEKA.

Wireless transmission of magnetometer readings.

Power profile analysis of CC430 experimenter’s board and HMC5883L sensor board.

Digital Clock Design (June 2014 - July 2014)

Designed digital clock using LPC1769.

Interfaced LTC-4627JR seven segment display with LPC1769.

Used real time operating system FreeRTOS for concurrent running.

Firmware Development (March 2014 - May 2014)

Developed device driver for LPC1769 to interface with AFE4490.

Used SPI protocol to send and receive data.

Network Security: Implementation of Demilitarized Zone (DMZ) (March 2014 - May2014)

Designed and simulated enterprise network model to demonstrate the Demilitarized Zone using OPNET IT GURU and Cisco Packet Tracer.

16 bit multiplier design using Digilent Nexys 3 FPGA board (September 2013 – October 2013)

Designed and demonstrated the working of 16 bit multiplier using Nexys 3 FPGA board.

Developed VHDL code in Xilinx ISE WebPACK.

Viterbi decoder design using Digilent Nexys 3 FPGA board (October 2013 – November 2013)

Designed and demonstrated the working of Viterbi decoder using Nexys 3 FPGA board.

Developed VHDL code in Xilinx ISE WebPACK.

Internet Based Intelligent Door Bell (March 2012 - May 2012)

Implemented intelligent doorbell using PIC microcontroller with MPLAB software.

Designed PCB layout using Eagle PCB design software.

ACHIEVEMENTS:

Completed a course on Embedded System Design using AVR Microcontrollers conducted by LI2 Innovations.

Chief coordinator in conducting a workshop on Building Autonomous Robots using Microcontroller at Jawaharlal Nehru National College of Engineering, Shimoga in association with LI2 Innovations.

Completed N+ course and CCNA course in IIHT.

REFERENCES:

Dr. Mohammad Mozumdar, Assistant Professor, California State University Long Beach, acte38@r.postjobfree.com

Contact this candidate