Gary A. Musser

**** ***

Lincoln Park, MI *****

Email: acq6sd@r.postjobfree.com

Phone: 313-***-**** no answer leave text message please.

OBJECTIVE:

To obtain an Electronic/ Instrumentation Technician or other open positions that will utilize my skills, abilities and commitment to excellence for the continued success of the organization.

PROFESSIONAL EXPERIENCE:

Advance Technical Services, Plymouth, MI 481170 10/2014 to 01/2015

Test Technician for JCI. Crash testing for seats and interior components setup for instrumentation on H3 models setups. Installed accelerometers, IRA and other instrumentation. Setup for camera's for high speed recording. Durability testing for seat track and seat position for component test with the use of PLC went cycling. Evauation and dianostics failure report and put into a Engineer program report called GLIMS.

Humanetics, Plymouth, MI 481**-***** 6/2014 to 09/9/2014 Certification Technician, Assembled test dummies for crash testing. Installed accelerometers, IRA's and potentiometers. Certification on crash dummies on instrumentation for customers’ orders using ATD Management System software for testing. Certification on instruments used in testing.

CDI Phoenix, AZ, Chula Vista, CA 3/2014 to 5/2014

Instrumentation Technician for UTC(Goodrich)Chula Vista, CA

Installed strain gages, thermocouples, and pressure taps on military aircrafts parts. Bonded strain gages to metals with two part adhesive with curing times associated with temperature and humidity.

Mid-State Technical, Davenport, IA

Test Cell Operator for CNH at Burr Ridge,IL10/2013 - 12/2013

Installed test instrumentation on large agriculture and commercial vehicles in a test cells. Fabrication of fixtures for instrumentation. Ran tests using PTO dynamometer loading, urea injection and diesel regeneration. Collected test data in to be supplied to test engineers. Installed Instrumentation (strain gauge, thermocouples, pressure transducers). Assembled and tested vehicle systems (such as engine cooling systems, hydraulic controls, flow rate for air induction system and urea injection modules). While running tests collected data using programs named Morphee and Cartouch. Data processing on spreadsheets for Engineers.

The Fountain Group Tampa 5/11 to 6/13

Instrumentation Technician for Pratt and Whitney Rocketdyne Jupiter, FL

Work in the SDR (Structural Data Recorder) Group where is responsible for accelerometers, strain gages, thermocouples, and transducers. Recorded Ambient Data Points and Calibration Checks before and after testing the engine. After a run (testing of the engine) Resistance Checks, Calibration Positive Voltage Checks, and a Calibration Report has to document for accuracy and updating the Test Definition File (TDF). Monitor different signals during testing to insure that the DSPCon is recording and uploading during transient cycles. Diagnose signals, and repairing and replacing instrumentation need for testing. Used JLG's to install instrumentation on the jet engines.

Electronic Restoration Services Livonia, MI 5/09 - 5/10

Senior Mechanic/Equipment Technician for Eaton Aerospace Warwick, RI

Disaster Relief for the floor. Service maintenance on machines that made airplane parts. Location: South Mid Wire Nashville, Tennessee. Service maintenance on power boxes, controllers, and electronic boards.

AVL North America Plymouth, MI 4/08 - 5/09

Service Engineer, installed FTIRs(Fourier transform infrared spectrometer), SDSs(Secondary Dilution System), and service maintenance and calibrations on gas dividers, analyzers, and dilution air systems for emission testing. MMDs(Mini Modal Dilution System). Used GEM110 software for setup figuration's, electrical/electronics setups for instrumentation. Calibrated all devices for measurement.

AreoTek Southfield, MI 8/06 - 2/08

Emission Test Technician for Detroit Diesel Corporation at Redford, MI

Rebuilt Mexa 7000 and some work on CVS systems. Did setups on NOX, COH, COL, CH4, O2, and THC analyzers. Ran curves, NOX efficiency checks, and HC Hang Up tests. Provide emission instrumentation and components test support to the Detroit Diesel Corporation (DDC) Redford Engineering Laboratory. Duties of an Emission instrumentation technician and a component test technician encompass a wide range of responsibilities including modifying, repairing, maintaining and calibrating a variety of emission equipment.

Kelly Services Southfield, MI 5/04 - 5/06

Electronic Instrumentation Technician for Ford Research Innovation Center, Dearborn, MI Fabricated wiring harness for all types of engines. Diagnose and repair all electronic and electrical related problems in the FIC chassis dynamometer wing and in the Vehicle Emissions Research Laboratory.

Roush Livonia, MI 12/02 - 9/03

Dynamometer Technician

Worked on prototype engines wiring harnesses. Testing engines for Fords, GM, and Honda. Setup engines for different types of tests. Operating chassis dynamometers in various testing labs. Downloading files to the network. Some pipefitting, electrical, mechanical installation of new test cells.

JE Jacobs Sverdrup Dearborn, MI 8/02 - 11/02

Engineering Associate for Ford Dearborn, MI

Assist with the operation of the tunnel. Perform routine metal working, mechanical, electrical and test cell installation and removal of test vehicles (mechanical, electrical, and instrumentation hookups). Maintain facility test cell areas and general test support equipment/tools required to perform vehicle testing. Provide general support to test cell operator during vehicle testing.

Link Testing Labs Detroit, MI 8/99 - 10/01

Service Maintenance Technician

Maintenance and calibration on dynamometer and other test cell equipment used for testing. Installed thermocouples, probes, load cells, string potentiometers, transducers, anemometers and keep calibration records in a DPC track file for audits. Estimated, purchased, and installed electrical, electronic, instrumentation, and mechanical equipment for new testing.

Education:

Diploma

Major: Electronics, electrical, and business. Lincoln Park High School, Lincoln Park, MI

Associate in Science

Major: Electronics with background in Electrical, Machining and Chemistry

Henry Ford Community College, Dearborn, MI

Certificates:

Test Systems and Devices Emissions

The Combustion Engine

ADACS Training Course

Heavy Equipment Operator

Miller Training

RCRA Hazardous Waste Management

Lead/Cadmium Safety

Electrostatic Discharge

Calibration System Manual Users

Personal Protective Equipment

Respiratory Protection

Gas Turbine Engines Advanced

Asbestos Awareness

ISO 9001

Laser Class A

Contact this candidate